How to Clean & Detail Your Engine
ฝัง
- เผยแพร่เมื่อ 26 ส.ค. 2024
- Detailing the engine of a classic car is a simple job, but in order to be done properly, certain steps must be observed.
You have two options:
1. Dry-cleaning the engine, which in some cases may be preferable, or
2. Wet-cleaning it with chemicals and water for rinsing
For this 1973 Corvette Stingray, we chose option #2 since the engine had not been cleaned in over 20 years!
In order to avoid starting problems, we insulated the carburetor, distributor, coil, and alternator with old plastic shopping bags and masking tape. This worked great as the car started without any hesitation after the detailing process was finished.
We also used a couple of products by Chemical Guys to protect the engine and also add a nice sheen to the now clean components, especially the coolant and vacuum hoses.
The job took approximately two hours and the results speak for themselves.
We are planning additional future projects for this Vette, and having a clean engine to work on will make the process more pleasant.
For more C3 Corvette articles, photos, and videos, visit www.76vette.com
Thank you for watching! 🙂👍🏻
======================================
CONTENTS
00:43 Waterproof Engine Components to Keep Them Dry
01:38 Prepare the Ground Surface Where the Engine Cleaning Takes Place
01:54 Apply a Good Engine Degreaser and Allow It To Sit for About 20 Min.
03:17 Use Brushes to Agitate the Dirt Buildup and Help the Degreaser
04:00 Use Water to Rinse the Degreaser and Gunk
04:36 Use a Clean Rag or Paper Towel to Remove Stubborn Dirt and Grease
05:55 Detailing and Drying the Engine Timelapse
06:28 Carefully Remove All the Waterproofing Tape and Bags
06:57 Inspect the Engine and do Additional Detailing as Needed
07:30 Start the Engine to Get Rid of Any Leftover Water and Help it Dry
08:16 I Applied a Heavy Coat of Bare Bones to Add Shine
09:31 And This is the Finished (and Clean) Engine
======================================
CORVETTE PRODUCTS (sponsored)
- Gunk Engine Cleaner and Degreaser, 32 oz: amzn.to/3ljISpX
- VRP Vinyl, Rubber, Plastic Dressing: amzn.to/38VOdN5
- BareBones Dark Shine Spray: amzn.to/3urWwKx
- How to Restore Your C3 Corvette 1968-1982: amzn.to/35B6L0R
- 1968-1982 Corvette Restoration Guide: amzn.to/2QvvIGQ
======================================
DISCLAIMER: Even though I like to wrench on my Corvette and most of my videos are of a how-to nature, I am not responsible nor liable should you decide to follow my musings on the subject.
The repairs and other work I do are for my own benefit and entertainment, and even though my videos may sound and appear to give technical how-to advice, that's not my intention.
Working on a vehicle is inherently dangerous. If you're not confident, qualified, or lack the tools to do the job correctly and safely, hire a licensed mechanic.
#corvettec3 #c3 #c3corvette
Makes a big difference! I can see you take pride in the care and maintenance of these iconic vehicles. Excellent content and video.
Thank you Ken. Much appreciated!
A couple more detail ideas just to help. First off, excellent on wetting the driveway first. Great tip! A small hand held pump sprayer is great for rinsing away grime when working small areas at a time. Use Popsicle or paint stick (sloughing the end) to hold paper towel when getting into tight areas. Air compressor, with the pressure turned down appropriately, to rid standing water. NO Leaf Blowers. Lighting and more lighting. You can foam brush paint for touch ups like the intake. Remember the prep is important. Helping a friend with a dirty, painful and timely job, Priceless!
Thank you for sharing these valuable tips. My bud Bob got motivated after we cleaned the engine and touched up the intake manifold. 😊👍🏻 Absolutely YES on the lighting. It’s so easy to miss critical areas without good light. Thanks again for sharing and following! 🙏🏻😊👍🏻
Great and informative video especially with show season 2024 starting. Thanks for doing these.
Thank you for watching! 😊👍🏻
I'm so glad I came across your blog. I have a 1978 Corvette (Silver Anniversary Edition). I'm about to remove the engine for a rebuild and these videos and articles are just what I need to take a great car to the next level. Thank you!
Thank you for watching! 😊👍🏻
Where do you get your period correct labels and decals?
@@thomasfurgal3039 I just search online. There are lots of reproductions available. Some high-quality stuff and, well, the rest. The same applies for things such window stickers, RPO labels, etc.
Happy Easter all my Corvette brothers and sisters. Another cool video. Great looking 73.
Happy Easter. 😊👍🏻
As always a great video. I do the same detailing to my C3 and 68 fastback. For those no paint areas on the intake manifold and water pump I touch them up with an acid brush and some can engine spray paint. I spray a little paint in the cap and use the brush to touch it up.
Thank you! 😊👍🏻
Yeah, Bob was saying we should brush some paint on and we may just do that next time we work on it.
The vac lines are hard as a rock, so he’s ordering new ones and we’re going to replace them.
Very nice Luis, that 73 sounds healthy!
Thank you! 😊👍🏻
Very beautifully done too!!
Thank you! 🙂👍🏻
My buddy is a detailer for a car dealership. When he go's to work on an engine the whole engine bay, motor, hoses etc look practically new. First he covers all the stuff you don't want get any product or water on.His cleaning weapon of choice is a good brand bottle of rim and tire foam cleaner. He foams everything he can access. After letting the foam work awhile take the water hose and rinse and repeat until you are satisfied. Anything that can be shined he uses spray nine and ddrys them with rags then applies Armour all to bring back the shine. Try the foam. It cleans everything that has grease or oil sheen and goes after any removable dirt around fire walls and inner fenders, etc
Another very nice video, l'amour du travail bien fait....as we say at home. thank you so much. 😊.
Thank you! 🙏🏻😊👍🏻