How is the drying performance? I read that washer / dryers in 1 don't dry as well ? Also, I saw a promo vid about this model that said the heating element is titanium and no limescale buildup ... Thanks
If there is no response from the buttons I’m afraid it’s a control panel issue, you’d probably need a new control panel. As the buttons are touch, there’s not much room for repair.
You can’t. The only way you can is to let the machine fill and work for 10 mins, pause it, let the door unlock and the add water that way, but the doors open so what’s the point
One thing I have picked up on if its vibrating or starting to vibrate, you have a bit to much in there. Dont forget all washing machines have to vibrate. if they didnt they would just break up, so just take care and try not to over load or it maybe something has balled up on distribute.
Hi Kevin, yes, that’s true, luckily the machine will ping and stop if it’s gets too bad for you to re distribute the load, I’ve never had that issue before, but once or twice I have noticed the machine has come forward a bit, but carried on. Thanks for the advice my friend. 🙏🏻🤗
i have a question that I have no clue whether anyone here will be able to answer. So i washed a down pillow tonight and I heard that you're meant to wash those on a no-spin cycle. So i did that using my hotpoint washing machine and then when i took it out (unsurprisingly) it was SOAKED with water. it was like holding a sack full of water. Tried wringing out all I could but no human is that strong. it's now in my tumble dryer on low heat with three dry towels that will hopefully help it dry, but my dryer is also being really iffy at the minute. I was wondering what the "spin and pump out" setting is and whether that would be any good for wringing out the pond of water that is in my pillow. Also, i washed this pillow by itself with no other pillows because i thought it would be better to do them one at a time so i was able to sleep with one every time the other was in the wash.
I have a few pillow wash videos on my Miele playlist, I washed feather pillows and yes, definitely spin them, but take care of balancing, I don’t put more than 2 in at a time and slowly crank up to fastest spin.
Its great until the bearings go. And then prepare yourself for a massive bill. Due to the design bearings cannot be removed so you need to buy the whole drum assembly. I've just learn that the hard way.
The Whirlpool Corporation group are specialist in term of production of garbage machines, and voluntarily non-repairables of course. And the worst is that this kind of dishonest company plays the ecological virtue ! The nerve of the capitalists is limitless
If your Hotpoint or Indesit washing machine lights are flashing with an F11 error code or on the digital display, it is generally associated with an emptying or draining problem. If your washer is not draining properly the most likely cause is debris stuck in the filter.
My aqualtis has corroded just under the rubber seal of the door. I bought it in jan 2015 ( I think). Any idea why it happened and what should I do now with this rusty bit
Sorry I couldn't be much use, but my mate did say that you need to make sure all or any residue or limescale on the inner bowl of the glass and the rubber seal.
This is what I found out. F12 indicates the main board at the bottom rear and the display board in the facia are not communicating. The wiring between them needs to be tested and if all is well you'll likely end up replacing the main board and possibly the display board too.
How reliable are these? My foster mum had a hotpoint from the late 70s up until the mid 90s it was still going but they moved and just left it. It's not a joke but that thing was going nonstop, it took care of 5 adults 4 kids for over 2 decades. At the maximum there were 13 people in the home, plus 3 dogs. No idea what they're like now but in the new house they got a hotpoint which from memory was quickly replaced by a Bosch.
Apparently the fact this one lasted as long as it did is a miracle I’ve been told, so apparently it’s not. I wouldn’t buy or own a modern Hotpoint at all. I’d rather have a Beko or a Siemens.
Wait , i was wrong , the time saver option would only reduce the time but it doesn't alter the rinsings on full load Also , i recommend doing a maintenance wash on 90°C with any type of washing machine cleaner each 2/3 months
I recently discovered this machine does a 90 wash 🤣🤣🤣🤣, I’ve done a few white 90 washes, but yes, I will put my washing machine cleaner through it today after seeing this message. Thank you my friend.
Yeah, I always do, it’s always left open a crack in between uses and thankfully I’ve never had a smelly machine. Wish I could send a snap as it’s now on a 90 wash with a bottle of washing machine cleaner I got from Aldi.
I prefer the LG as the drum is bigger and I can see inside the door, plus I didn’t like the fact you couldn’t access the drawer at all firming the wash.
Our model is AQ 113D 497 and the BABY ICON is lighting and the machine doesnt function i guess because of that, how can i UNLIGHT that baby icon? Thank you...
And if i can give you a tip, use only powder detergent, the liquid and wrost the pods, leave a lot of residue on your machine and it gona last nothing, trust me, is like if you have a ferrari and dont put he gasoline in, have an amazing washing machine give her the right detergent. Only powder
I only use powder with the white was and half half with colour and only pods with darks as the powder sometimes leaves residue on my dark clothes, so it does get a good clean out too every few months with a washing machine cleaner. Thanks for the advice 😂😂😍
HooverLux thank you to for sharing the video of your amazing washing machine, but the way the dark programs always have a super rinse, extra rinse for avoid powder residue, you can also add an extra rinse, but the way if you only use the pods for dark and for the rest only powder im think your are gona be ok, just a cleaning cycle every mounth for limescale and detergent residue, there are a lot of product for this use.. thank you so much from Italy 🇮🇹 I love uk, I allways came there to spend my vacation in London, amazing kindness people's 😍😍😍
Awwwww, thank you my friend. Where I live the water is very very hard, so I always use a washing machine De scaling tablet called Calgon. I’m positive it helps. I think using the powder on whites at a high temp also helps🙏🏻, so far so good. I’ve not been to mainland Italy yet, but I’ve been to the island of Elba and that was awesome.
Hey, you know that the water go accross your drower and take the mud and put it in your clothes? So everything you wash ther have the same mud under, is very important clean your machine
Try holding the button for a few seconds and that may cancel it, normally 3 to 5 seconds. I can’t remember having that issue, I hope it’s not a fault with the machine 🧐
HooverLux Does it leave the clothes clean after 2 hours? I ask because it seems like its a lot of clothes , im about to buy this washing machine, do you still recomend it?
Ah! Argentina 🇦🇷 besos por tiny por su pais incredible. Soy Gales originalmente un parte De mi familia es en Patagonia. You have an incredible country with the best meat I have ever tasted. Saludos y Amor Argentina x
Trevor & Simon needed one of those in their launderette! (I hope you understand that - you're only a year younger than me, so you might!) Does bed and bath mean you can wash towels and bedclothes in the same load?!
To be honest I was going to buy this washing machine for my mum for Christmas but it was £600 on Tesco website so I was like sod that so I brought a washer dryer what was £320
+mathew marsh I just wanted a machine that if I looked after and used as instructed, would last a decent length of time. The other factor was the large capacity for washing bedding and big loads in one go and was really energy efficient. The price is definitely a put off, but I’d bought 2 roughly 300 quid machines in the past 10 years and they’d not been as reliable. It’s luck of the draw tbh.
It's not direct drive only lg washing machines do that and lg have patents the direct drive so no other company can use it but your hotpoint has a brushless motor witch means it's very quiet and just as good
panic at the disco lover Ooh, no? I’ve not heard of them? I’ve just googled. I will have to try them, they should be good in my twin tub too? 😮. Thank you 🙏🏻
@@HooverLux lg direct drive is a motor which directly connects to the back of the drum, other brands have the motor in the standard place, at the bottom of the drum
Hola Equador. Mi encanta su pais. Mi conoces a Quito. Muy bonito ciudad. Disafortunatamente no sabes sufficiente los codigos De su Lavadora. Si puedes buscar a Google o contactar a su manufacturer. Lo siento amigo 😢
I hope you cleaned the detergent drawer, because water go on the muld and than on you clothes if you figure it out buy your self i dont need to say nothing more!
Oh gosh, I’m not sure to be honest, I’m more of an end user and enthusiast when it comes to washers and driers. I hope an expert reads this to give an answer. Sorry Juan 😢
That is a good idea, but I always leave the door and drawer open a crack which prevents any of that. I’ve never had a machine suffer from smells cause I do that little trick. My mum and nan did the same.
The control screen on mine got fcked after 6 years cant find replacement... cant replace bearings, you need to buy the whole drum... to hell with this machine honestly
FrownyFace Hey Frowny Face 😘. I know exactly what you mean! When I found out I’d have to buy the whole bloody drum and recommended new seals and a heater I thought stuff this and went for the LG. I know it’s not the best machine, but I loved its capacity, quietness and the cycles are fun. Plus I had almost 500 quid off as it was a scratched (cosmetic damage) so I couldn’t say no! 🤣. I did want to fix the HotPoint, but I’m glad I didn’t in the end.
I fix myself bearings in a drum. Drum must cut off then U can fix bearing. You can use silicon for 300°C and glue drum again. Make holes on drum and use screws. I can sent U photo how it looks.
I am looking as hard as I can for another one I loved the previous which lasted from 2013 until 2019
It’s gonna be hard to find one in decent condition now 😥
@@HooverLux I get that now I do quite like the Bosch serie 8 I-dos too
How is the drying performance? I read that washer / dryers in 1 don't dry as well ? Also, I saw a promo vid about this model that said the heating element is titanium and no limescale buildup ...
Thanks
Spin dry? It was good.
What might be the problem if the control panel is not booting,if i switch it on
Probably needs a new board
I'm having trouble with the touch panel on right side to start and childlock , can this be fixed any help much appreciated, doesn't respond at all
If there is no response from the buttons I’m afraid it’s a control panel issue, you’d probably need a new control panel. As the buttons are touch, there’s not much room for repair.
Please how can I add water to the machine. I've been trying to make use of it but didn't get the way of adding water
You can’t. The only way you can is to let the machine fill and work for 10 mins, pause it, let the door unlock and the add water that way, but the doors open so what’s the point
@@HooverLuxwhen it is working and you have to go suddenly you cant switch it off. am i true?
One thing I have picked up on if its vibrating or starting to vibrate, you have a bit to much in there. Dont forget all washing machines have to vibrate. if they didnt they would just break up, so just take care and try not to over load or it maybe something has balled up on distribute.
Hi Kevin, yes, that’s true, luckily the machine will ping and stop if it’s gets too bad for you to re distribute the load, I’ve never had that issue before, but once or twice I have noticed the machine has come forward a bit, but carried on. Thanks for the advice my friend. 🙏🏻🤗
Эта машина на 11 кг. Она не может быть перегружена.
How do you take out the detergent drawer to clean it?
From what I remember is you just pull the drawer out, I can’t remember any clips or anything
HooverLux Restorations thank you👍🏻 although i have tried many times but could not take it out☹️
i have a question that I have no clue whether anyone here will be able to answer. So i washed a down pillow tonight and I heard that you're meant to wash those on a no-spin cycle. So i did that using my hotpoint washing machine and then when i took it out (unsurprisingly) it was SOAKED with water. it was like holding a sack full of water. Tried wringing out all I could but no human is that strong. it's now in my tumble dryer on low heat with three dry towels that will hopefully help it dry, but my dryer is also being really iffy at the minute. I was wondering what the "spin and pump out" setting is and whether that would be any good for wringing out the pond of water that is in my pillow. Also, i washed this pillow by itself with no other pillows because i thought it would be better to do them one at a time so i was able to sleep with one every time the other was in the wash.
I have a few pillow wash videos on my Miele playlist, I washed feather pillows and yes, definitely spin them, but take care of balancing, I don’t put more than 2 in at a time and slowly crank up to fastest spin.
Its great until the bearings go. And then prepare yourself for a massive bill. Due to the design bearings cannot be removed so you need to buy the whole drum assembly. I've just learn that the hard way.
If you carry on watching other vids you see the do and yes, I got a new machine 🤣🤣🤣🤣
The Whirlpool Corporation group are specialist in term of production of garbage machines, and voluntarily non-repairables of course.
And the worst is that this kind of dishonest company plays the ecological virtue !
The nerve of the capitalists is limitless
How do you fix it says memorised and it doesn't start it pumps out water but doesn't start
I’ve not had this machine for a few years now, I can’t remember, sorry
I'm getting a F 11 fault coming up on mine any help would be greatly received
I've checked all the obvious water turned on no kink in water pipe etc
If your Hotpoint or Indesit washing machine lights are flashing with an F11 error code or on the digital display, it is generally associated with an emptying or draining problem. If your washer is not draining properly the most likely cause is debris stuck in the filter.
My aqualtis has corroded just under the rubber seal of the door. I bought it in jan 2015 ( I think). Any idea why it happened and what should I do now with this rusty bit
You can rub it down with fine sand paper, paint on som Kurust and then some enamel paint over that, depending on the colour of the machine.
Thanks a lot for the advice
Sorry I couldn't be much use, but my mate did say that you need to make sure all or any residue or limescale on the inner bowl of the glass and the rubber seal.
Hello it ana amazing Video it helps a lot , please i need your help if i have F12 fault how can i fix it ?
Thanks a lot...
This is what I found out. F12 indicates the main board at the bottom rear and the display board in the facia are not communicating. The wiring between them needs to be tested and if all is well you'll likely end up replacing the main board and possibly the display board too.
How do you remove child lock and I how do I get the machine to run on eco mode to keep the leccy down a boil wash takes 3 hours to complete
I have an f5 error and cannot complete any cycle and drain it. So clothes still inside with water. Any help or suggestions please
That’s a pressure switch or pump error.
Please i need help here but why is the water pomping out of the washing machine ?
How do you mean? Can you give a video time stamp for me to hear. Thanks.
I mean, today is my first time of using my machine and to my surprise water is pumping out of the washing machine
OK, do you mean continuously or just when its supposed to drain?
How reliable are these? My foster mum had a hotpoint from the late 70s up until the mid 90s it was still going but they moved and just left it. It's not a joke but that thing was going nonstop, it took care of 5 adults 4 kids for over 2 decades. At the maximum there were 13 people in the home, plus 3 dogs. No idea what they're like now but in the new house they got a hotpoint which from memory was quickly replaced by a Bosch.
Apparently the fact this one lasted as long as it did is a miracle I’ve been told, so apparently it’s not. I wouldn’t buy or own a modern Hotpoint at all. I’d rather have a Beko or a Siemens.
Please remember I’m far from being an expert on these and still very much just an end user.
I've had mine since 2012, 2022 amd still going strong. Not had one problem since I bought it. Absolutely love it!
Wait , i was wrong , the time saver option would only reduce the time but it doesn't alter the rinsings on full load
Also , i recommend doing a maintenance wash on 90°C with any type of washing machine cleaner each 2/3 months
I recently discovered this machine does a 90 wash 🤣🤣🤣🤣, I’ve done a few white 90 washes, but yes, I will put my washing machine cleaner through it today after seeing this message. Thank you my friend.
@@HooverLux No problem , u have also to leave the door open after washes to prevent bad smells 😁
Yeah, I always do, it’s always left open a crack in between uses and thankfully I’ve never had a smelly machine. Wish I could send a snap as it’s now on a 90 wash with a bottle of washing machine cleaner I got from Aldi.
Hola,sabes si tiene lavado corto,sin secadora, gracias
It does have a short wash yes, but I’ve not had this machine for years now so I can’t remember
@@HooverLux gracias
Is better his o the new lg that you got? Comparison? Maybe this have very long cycles?
I prefer the LG as the drum is bigger and I can see inside the door, plus I didn’t like the fact you couldn’t access the drawer at all firming the wash.
Our model is AQ 113D 497 and the BABY ICON is lighting and the machine doesnt function i guess because of that, how can i UNLIGHT that baby icon? Thank you...
joyce nacu try holding the baby button for a few seconds to turn it off, if not it could be a problem with the PCB board?
take baby out
🤣🤣🤣🤣🤣🤣
I'm getting 'Testing' on the screen and it has not completed the cycle. Can u help plz
I’ve not had the machine for almost 2 years now. Sorry
Can anyone tell me wat setting you use for permanent press when washing thank you
Ive not had this machine for a good few years now, I can't help i'm afraid.
Please can u tell me how to manage the time (i load lile 5 kg the program selected automatically 4 hours)!?!?!
I don’t have this machine any more, I just used the time saver option to shorten load times, you could only use it in certain programmes.
@@HooverLux thanks man 👌
And if i can give you a tip, use only powder detergent, the liquid and wrost the pods, leave a lot of residue on your machine and it gona last nothing, trust me, is like if you have a ferrari and dont put he gasoline in, have an amazing washing machine give her the right detergent. Only powder
I only use powder with the white was and half half with colour and only pods with darks as the powder sometimes leaves residue on my dark clothes, so it does get a good clean out too every few months with a washing machine cleaner. Thanks for the advice 😂😂😍
HooverLux thank you to for sharing the video of your amazing washing machine, but the way the dark programs always have a super rinse, extra rinse for avoid powder residue, you can also add an extra rinse, but the way if you only use the pods for dark and for the rest only powder im think your are gona be ok, just a cleaning cycle every mounth for limescale and detergent residue, there are a lot of product for this use.. thank you so much from Italy 🇮🇹 I love uk, I allways came there to spend my vacation in London, amazing kindness people's 😍😍😍
Awwwww, thank you my friend. Where I live the water is very very hard, so I always use a washing machine De scaling tablet called Calgon. I’m positive it helps. I think using the powder on whites at a high temp also helps🙏🏻, so far so good. I’ve not been to mainland Italy yet, but I’ve been to the island of Elba and that was awesome.
Thank you, fingers crossed 🤞
Hey, you know that the water go accross your drower and take the mud and put it in your clothes? So everything you wash ther have the same mud under, is very important clean your machine
Our machine doesnt work coz the BABY BUTTON is lighting. How can i cancel that baby light? Thank you...
Try holding the button for a few seconds and that may cancel it, normally 3 to 5 seconds. I can’t remember having that issue, I hope it’s not a fault with the machine 🧐
@@HooverLux thank you! I'll try that later...
this is so helpful
Thanks 🥰
Come devo resettare la lavatrice ariston
I’m afraid I don’t know.
Have they stopped selling these? Can't find them anywhere
Yeah, they needed production about 4 years ago from what I’ve found out.
Hi my machine is stuck on steem refresh mode let me know plz how can i start it again
Rizwanatahir Tahir hi, have you tried turning it off at the wall and leaving it for a few mins and then turning it back in again?
it is good Washing Machine or bad ???
It was good, had no major issues with it before the bearings went.
@@HooverLux Wait what was the average life expectancy of those bearings?
HooverLux Does it leave the clothes clean after 2 hours? I ask because it seems like its a lot of clothes , im about to buy this washing machine, do you still recomend it?
Hi, I find the clothes to be always clean. I can highly recommend this washing machine. Look after it and will last
HooverLux thanks for the quick answer, you have a new new suscriber now ;) great job, saludos desde argentina !!, greetings from argentina
Ah! Argentina 🇦🇷 besos por tiny por su pais incredible. Soy Gales originalmente un parte De mi familia es en Patagonia. You have an incredible country with the best meat I have ever tasted. Saludos y Amor Argentina x
Can you still buy these?
Not new no unfortunately
Oh :(
Svp comment debloquer la porte de cette machine(Aqualitis)
Trevor & Simon needed one of those in their launderette! (I hope you understand that - you're only a year younger than me, so you might!) Does bed and bath mean you can wash towels and bedclothes in the same load?!
They were the guys that came out with that song like shwing your pants? I’ve only ever washed them separate? But I guess you could? 😂😂
Hola soy de España y se me ha bloqueado mi lavadora igual a esa y no centrífuga me sale un F 5 en la pantalla.
Que debo hacer?
este código de error es drenaje. Deberá comprobar la manguera de aguas residuales, la bomba y también el filtro.
Muchas gracias al final era el filtro por lo que no centrifugaba.
To think all these years later how many washers you would have lol
I know right 🤣
Another important thing, the door is suppost to leaved open when you dont use it, allways
I leave it open a crack because if I left it open, one of the cats goes in and sleeps in it!!!!!! 😱😱😱
HooverLux yeas but his way allways gona appear mud and the inside and back of berings gona make some rust much quicker
Ok thank you!!!
@@HooverLux thank you!!!
To be honest I was going to buy this washing machine for my mum for Christmas but it was £600 on Tesco website so I was like sod that so I brought a washer dryer what was £320
+mathew marsh I just wanted a machine that if I looked after and used as instructed, would last a decent length of time. The other factor was the large capacity for washing bedding and big loads in one go and was really energy efficient. The price is definitely a put off, but I’d bought 2 roughly 300 quid machines in the past 10 years and they’d not been as reliable. It’s luck of the draw tbh.
Does it contain dryer?
Hi, No, this was just the washing machine only.
How do you get it to go on eco mode
Oh gosh, I can’t remember, I can’t even remember using the eco mode to be honest.
Lower the temperature
How do you remove the child lock please help zxx
You push and keep pushed the lock button until it beeps
It's not direct drive only lg washing machines do that and lg have patents the direct drive so no other company can use it but your hotpoint has a brushless motor witch means it's very quiet and just as good
Also you need to leave door and detergent drawer opened after using
Yes, I always did. To be honest my mum used to and so I’ve just always done it. Luckily I’ve never had a smelly machine.
Merhabaaaaa :) = This Türkçe merhaba ..
This talking about "machine self clear" is it?
How do you mean self clear? Sorry
@@HooverLux Soma machine Clear self (inside)
@@NOBOYOAdrum clean actually
Have you tried persil power gems
panic at the disco lover Ooh, no? I’ve not heard of them? I’ve just googled. I will have to try them, they should be good in my twin tub too? 😮. Thank you 🙏🏻
They do smell nice
Is it okay if you could do video at some point of it they'd also power caps as well and surf power gems
panic at the disco lover absolutely, I’ve some twin tub vids coming up soon 🙏🏻
What washing machine did they aqualtest replace
Il tasto dove si accende e verde dove sta la faccine e arancione e non va
Only yours is quite...mine does a lot of rumours specially when works the last circle of laundry
Oh right, hope it lasts for you.
I thought direct drive was only on LG washing machines.
Sharon Hopton well! So did I, but apparently not? I was surprised to find out, but Samsung also do DD machines and I’m sure another?
@@HooverLux lg direct drive is a motor which directly connects to the back of the drum, other brands have the motor in the standard place, at the bottom of the drum
Tengo una lavadora aquality tiene la falla me da código f13 ayúdame que daño puede ser saldos desde Ecuador
Hola Equador. Mi encanta su pais. Mi conoces a Quito. Muy bonito ciudad. Disafortunatamente no sabes sufficiente los codigos De su Lavadora. Si puedes buscar a Google o contactar a su manufacturer. Lo siento amigo 😢
Thanks
Cousin
Have the same machine
With model is aq83d29
Ah ok, and it’s still working?
@@HooverLux yes perfectly working
I hope you cleaned the detergent drawer, because water go on the muld and than on you clothes if you figure it out buy your self i dont need to say nothing more!
Yes, I used to clean it out every few months, whenever I’d do a machine clean cycle.
Puede ser el video en español?
Yo tango un video en espanol pero no fue popular 😢
And my Hotpoint Aqualtis AQ113D 697E is totally dead. Wont ewen start up.
Noooooo! When? Why? How old is it?
I have Problems with this wash dryer f 8 😤
If you google the make and model and the error code, you will find out the issue. I’m afraid I’m just an end user.
Heater problem
The hotpoint machinese have more problems than Ariston from Italy.. why ?
Oh gosh, I’m not sure to be honest, I’m more of an end user and enthusiast when it comes to washers and driers. I hope an expert reads this to give an answer. Sorry Juan 😢
@@HooverLux I think Hotpoint makes Indesit the most hated brand
sans comic they all seem to own one another is some way 🤣
Its good brand Ariston finally all brands have problems but when the factory have sub brands need more controls lol
I think buy the washing machine dryer inverter its magnifhique !
تعليم تشغيل غساله اتوماتيك درجات ارستون تسع كيلو
najat abdola اختي عرفتي تشغليها شغلتها بس المشكلة ابغاها تجفف ١٠٠ما جففت لي
I’m afraid I can’t understand, but I love the style of Arabic writing.
سلام أختي وين أشتريها أبي مثلها صراحة حلوة
What 2 1\2 hour's for a wash wow thats insane
I use limescale tablets but live in a soft water area to keep it smell hygienic
That is a good idea, but I always leave the door and drawer open a crack which prevents any of that. I’ve never had a machine suffer from smells cause I do that little trick. My mum and nan did the same.
HooverLux my grandad has one of these machines which is 7.5kg which is 9 3/4years old it's fantastic
Wow! That’s so cool, I’m glad it’s still going strong, what’s his secret to looking after it? It’s like the secret to eternal youth 😍😂😂.
HooverLux don't know he likes to use bed and bath cycle and colours 40
The control screen on mine got fcked after 6 years cant find replacement... cant replace bearings, you need to buy the whole drum... to hell with this machine honestly
FrownyFace Hey Frowny Face 😘. I know exactly what you mean! When I found out I’d have to buy the whole bloody drum and recommended new seals and a heater I thought stuff this and went for the LG. I know it’s not the best machine, but I loved its capacity, quietness and the cycles are fun. Plus I had almost 500 quid off as it was a scratched (cosmetic damage) so I couldn’t say no! 🤣. I did want to fix the HotPoint, but I’m glad I didn’t in the end.
I fix myself bearings in a drum. Drum must cut off then U can fix bearing. You can use silicon for 300°C and glue drum again. Make holes on drum and use screws. I can sent U photo how it looks.
Please give me the bearing serial number.
I’m afraid I no longer have the machine and don’t know any of the details.
5:19 5:23 5:24 5:24 5:25 5:25
Absolutely no idea what you mean
Pir favor en español
Tengo algunas videos en español, pero nadie te gusta disafortunatamente 😢