ฝัง
- เผยแพร่เมื่อ 1 ต.ค. 2024
- #samsungtvstuckonlogo, #samsungsmarttv
in this video, we show you how we fix Samsung led smart tv stuck On Start Screen Logo.
programming EEPROM then add thermal Paste to decrease the heating of the processor, after that we show you how to rotate the image in Samsung led tv.
DONT CLICK THIS: bit.ly/3uGbn3S
link for dump EEPROM: bit.ly/33Voq60
buymeacoff : bit.ly/2ScZNv5
if you like video, Don't forget to Like, Comment, Share and Subscribe to my channel
Hello Sir, please, i need bin file for UN46H6203AKXZL, Thanks a lot!!!
What for is using flux in non contact desolderig? Better would be add some lead tin to pins to lower melting point temperature
If you have a samsung smart tv (model CU8000) in 2024 like me, with just smart remote or have broke screen, this process works for me:
1. Turn on the TV.
2. Hold down the power button on the TV itself for 5 seconds.
3. Then immediately after, hold down the remote's power button for 5 seconds.
5. The TV will be off for about 30 seconds and then turn on.
6. The TV will enter installation mode. Now unplug the power cable from the TV for 30 seconds.
File is from BN94-07111U, if I upload it smart is off? Dont smart ?
Please i need dump for spi 25x10clnig
Main Board tp ms338 pc821
FHD smart tv
Android 4.4
Panel v390hj1-ce3
Thankyou
Well done. How do you know where the location of eeprom is on the motherboard?
Hello Sir do u have bin file of samsung ua48j5200ar?
tomorrow i reply you
i need bin for nand tv samsung UN40D5550 Can you help me whit this file my tv stuck on logo
send me part number graved on mainboard
my not resolve with 24c512
hello samsung 5570asxtk led tv motherboard bn94-08121z when the tv is turned on, it writes smart and turns off again and repeats the same process I have a bin file apparatus, can you send a file, thank you
Hi please i need Dump or bin file to flash eeprom tv samsung Modell ue50f5570ss or motherboard model ue50f6470 bn94-06231u. can you help me thanks
I have the Panasonic TX-50AX802B stuck off logo screen, I have tried the USB update but nothing happens when I turn on TV. Please advise thanks in advance
sir ...ive got the same problem ..on samsung ue27d5010..panel VN96-18829c,,....PCB CODE BN41-01602A..where can i find the eeprom.. i hope your kind and consideration...salamat po...
my innjoo Smart tv same problem
ho to solve it?????
I have a problem with the Samsung Smart TV starting also. When I plug in the power cord the TV immediately turns on, The icon of Smart TV will come and go and then it will show HDMI2 on the upper left corner for a little while and then the TV turns off. Few seconds later it turns on again and does the same than above. With the remote I have no control what's so ever. Only way to turn it off again is to plug off the power cord. What could it be/ how to fix that? 🤔😁
the problem on firmware . must reprogram the ic eeprom or the nand ic .
@@repoapps Ok thank you so much for the reply and the help. I'm not an expert with these myself so in this case I think it's probably better for me to bring the TV to somewhereto be fixed. Most likely this ic eeprom or nand ic programming will need some special equipment to be done. Otherwise I could try to do it myself. 😄
Ironic that it says Smart TV...lol
Great job! ;-) Please, UE55H7000 (bn41-02156) after a few seconds the Smart TV logo disappear, but no more activity. Is programming eeprom the solution? Do you have program for this type? Thank you ;-)
Hi watched your video great video
Can the same be done to a Panasonic tx-50ax802b tv where the logo is stuck
I've looked for new board but no where can I get one and many have same problem
If it cam be done have you the file I need and also where the chip is located Id code ect on the board
Hope you can help it's becoming a pain now to fix if this doesn't work il probably just strip it for parts
send me the part number printed in the mainboard
@@repoapps hi thanks for reply the part number says on board
Tnph1100 (2)a
@@repoapps ho did you manage to find out for me what part the firmware is stored on and identification to it
Hi paul, I have the same problem did you ever get it sorted.
Cheers Shane
@@computerfixitlondon I gave up in the end the board for that tv is so hard to get hold of
I bought a chip remover thinking could reprogram chip but I don't have the best soldering skills so ruined the board in the end
I ended up just selling for parts
Salam 3andi mochkil fhal hadak fayn 3andak mahal
Hello please can this method work on Panasonic tv 58inches stuck on logo too
i think the panasonic model you have is android system, so download the firmware update from official web site then update your tv with usb stick .
UA40H5570UA,the model of the mainboard is BN41-02156A LOGO COME restart next Smart Hub Terms & Conditions,Privacy Policy on display remote & key notworking from india
Why the Logo(samsung smart tv) appear? Because of what? The user have a wrong way to play the TV or because that TV is damage?? I have that problem too, please help me to answer this
Hola, Tengo el mismo problema, aparece logo smarTV y desaparece y se queda en pantalla negra. Es un Samsung UE48HU7500L con placa modelo BN41-02205. Por casualidad no tendrías el archivo .bin para dicho modelo?. Gracias
Bonjour. J'ai un problème en SMART tv uaf6400aw ne salum pas plac alimentation bien et merci
hello nice video! how to solve smart tv samsung model ue48h6240ay. and main board bn97-07307x problem eeprom?
Like from Russia!
there is simply NO reason youre not talking ... we have the technology .. we can See AND hear at the same time...
useless.. thumbs down ..
I don't reprogram it I just put another one in and it worked
you are lucky, happy for you
Bon travail : même problème avec mon tv problème samsung UE48h6200AW smart TV logo smart TV toujours afficher à ce que la même solution j'attends votre réponse SVP. MERCI
Sag mal wie tippst du den Modell eigentlich ein ??
Mit der Fernbedienung funktioniert das schonmal nicht ....
Today, I entered the hidden menu on Samsung Smart TV to install Bluetooth on the TV. I accidentally clicked on the submicom upgrade. After clicking there, the sound of a television first disappeared, then the image does not work at all. Is there any feedback, please give information about them. I could not reach any information in my researches on the internet. If the menu is locked by pressing the mute off button, the menu must be a way to bring it back. They said that the way to bring it back is to rewrite Nand Flash IC and said I need a flash programmer and motherboard dump file for it. I watched your video. You mentioned the dump files of mmcs. Can you do this for samsung smart tv?
Technical information of TV:
(card no) BN94-05841S, BN41-01812A, SAMSUNG UE40ES5500W (model no)
serial no: B4LF3HEC60116L
first try to reprogram the eeprom ic .. if not working then reprogram the nand ic ..
in my video i reprogramming the eeprom with a good dump file .
i think your issue is not on nand ic , you have changing some values when you have entry in hidden menu , and this information is stored on eeprom ic .
i had a same problem for samsung UA46ES7500, MB part no : BN94-05578G. i already found the ic-24c512. Are you have a bin file for this type ?
ok i will search if i have it
My Samsung Smart TV model: UA55H6400AK does not want to start. when I turn it on, it turns on, and displays on the screen: SMART TV (that's all, can not go to the MENU) no way to turn it off unless it's unplugged.
firmware problem, if you have skills you can fix it if not you need to change the mainboard
Hello good sir, do you happen to have the eeprom dump for ue49ks7500 or any other similar model from which I could use the dump file? Thank you for your time
send me the part number of mainboard
Can I just get the entire board answer just swap out ? My 65 inch just did this today
Qual o modelo DA TV
Queria saber qual é o arquivo que usou,a minha TV Samsung Smart TV ue32h5500aw tem o mesmo problema.
Thank you for this guide. I was able to fix my UE32H5500K using this method!
happy for you 😉
Hi, Where can I get the dump for a Sony KDL 32L4000? Thanks
Hola , es posible cambiar el logotipo de inicio de los televisores samsung al inicio? , tambien es una opcion eliminarlo , como seria el proceso ? que herramientas se necesita para esta tarea ? si alguien me puede colaborar con este proceso puedo pagarme unos cafes por paypal, (celularespia*gmail.com) Gracias .
Please how enter in recovery mode or factory reset without menu, i have black screen in my skyworth tv android 8 , i have only one bouton in back of tv, joystick bouton for start/shutdown.
Modele of my tv is 43g6 smart tv
Nice video but more information regarding programming the chip would have been awesome
Bonsoir j’ai vue votre video et he voudrai bien savour commment repparais ma Panasonic TX50-AX802b merci
hi, you have file for blaupunkt 32/122i-gb-5b-hbku ????
&
hi, and thanks for the video, what can i use for UN55D6003 ?
Hi, excellent work, well explained. Have you the bin file for Philips 55PFS8159-12 ? QV14.1E LA
Thanx for your help
for your model , the tv have android system so you need to search for firmware from official web site then update your tv .
if not working you need to enter on the recovery mode then use file wipedatatool to resetting the tv . you can google it . good luck 😊
I'm not sure but ,if anyone else wants to uncover
computer repair tips
try Saankramer Electronic Magazine System (do a google search ) ? Ive heard some interesting things about it and my partner got amazing success with it.
Hello, can you possibly help me repair a samsung d8000
Dear repo apps,
thanks for this valuable video.
I have samsung smart tv model UA40F5500AR always rebooting.
do you have the bin file for it.
thank you.
please note that the download links for the IC K9GAG08U0E is not working. is there an alternative links.
see on mega : bit.ly/2T8PaKt
Quell site tu trouve le datasheet pour Des eeprom tu me peux pas voir le Numero
Do you have binary file for Samsung un40eh6030mxzl? or where can I look for it?
Thank you, good video
Yes
Great video man, i dave the exact same probleme that you show in your video, but i have a little problem .
By distraction Instead of reprogram the Eeprom 24c512 I reprogram the spi 25q16 without saving the original file (I know it was stupid), so I really apreciate if you can by some way send me the .bin file of your mother card becuse we have the same model
ok i will send it to you no problem
@@repoapps thaks
on my board i have 25Q40 ?
Hi Repo apps,
On 1:35 you show us a SPI25Q16, what to do with this one? also replace? In the video I see you only desolder the Eeprom 24c512 reprogram it and put it back, you do nothing with the SPI, can you explain me please?
Further I have a question, can I send my bad Eeprom to you so you can reprogram it for me? I dont have a programmer.
Thanks in advance!!
yes i desolder just eeprom and reprogram it with good file . where are you from ?
@@repoapps I'm from the netherlands, were are you from?
My Eeprom is a Winbond 25Q40CLSIP. My Motherboard is a BN94-07369T The TV is a Samsung UE48H5570SS
The problem is exactly as yours, stuck at logo screen.
no ,problem is not caused with spi 25Q16 , the eeprom s24c512 caused the issue.. so you need to program it .. in your mainboard is located as ic901 ..
ok send me your address in my facebook page then i send you ic already programmed..
@@repoapps Aaaaah, I was wrong! Thanks for your help. I will
send you my address in fb, please tell me the cost so I can Pay you for your work.
MY SONY KLV32ex400 TV.. I change new T con board..causing Green and
orange flashing I tried to firmware update using USB stick..red light
light up, orange light flashing USB stick flashing.its start
updating.but after 10 minutes..everything was change..USB stick stop
flashing..and green , orange light was flashing....so I discontinue the
process....update was failure..Now every time I turn on the TV..green
and orange light is flashing..no picture and no sounds....Please help me
with this,,,can I use this procedure from the video?
your tv sony is different, each mainboard have specific software. so in your case i think you need to reprogram the flash ic with good working software, you need skills to do that , open tv check the ic flash number then desolder it , use good programmer then reprogram the ic .
repo apps I Think its my fault.. when I review the Tcon board today it has different Part number written in the sticker but both has the same board number.... I think the tcon is not compatible with my logic board.. that is why I can not continue the update...
Good working brother aa
Hi, nice tuto, can you help to find binary file for a samsung UE40H6200AK?Thanks!
it's the same mainboard, use the same bin file, but save your original bin file first , see description for link
Excellent work sir
WHERE I CAN found Samsung UN50JU7500 (BN94-09984A) EEPROM FOR SAME PROBLEM
test this dump file-upload.com/d/Cqj9
but first save the original dump .
THANKS MAN, I'II TRY
the board(TP.MS338.PC821) does not have eeprom.ITS WINBOND FLASH 25X10
Software problem
Thankq sir
repo apps ... parabéns e obrigado pela dica. Poderia me dizer quanto graus você utiliza para retirar e soldar o chip sem danificá-lo???
Thank you for information and bin file
Greetings from Greece
Super
sir plz help me
CAN DO THIS BY USB
no sir
Thank you
Salam akhi
Merci pour les infos
J’ai une smart tv ua32f4500
Pb store application ne s’affiche pas même les applications
J ai fait installé le fichier bin 24c256 sur eeprom mais le même pb
Merci de ria géré sur la
entrer sur service mode et fait reset , si le problème n'est pad résolu tu dois programmer le ic nand avec un bon firmware, si t'as un programmeur de flash nand je peux t'aidera pour résoudre ton problème, bon courage
How to rest munu cahier smart tv samsung
por que no subes el dump plis
see the links on description, bit.ly/33Voq60
@@repoapps good day sir do you have firmware for samsung ua40ju6000r board number BN94-10705A SPI IC 25Q40CLSIP WINBOND
Where i can find firmware ua40eh5300 samsung. My samsung stuck logo smarttv to.
sorry i don't have bin file for your model , you can read the original eeprom dump and send it to me to fix it .
How about Lg 42 LE5500 -TA its stuck logo Lg when i turn on the power. What is the problem my tv
this model have famous issue . the problem : the processor is desolder.
so you can reballing the processor , or change all mainboard.
Hi sir, when i switch on my tv (skyworth 40e2000), it will open the main logo screen then it will just keep on loading. Can you help me figure out the problem?
you need to reprogram the ic flash with good file . so you need a programmer, send me the number model printed in mainboard to send you bin file .
@@repoapps thank you so much, i will send you the model number as soon as i got my hands on it. Thank you so much for the help.
Do you have firmware for samsung MODEL BN41-01958
it's the same eeprom
@@repoapps can yo u send me the link
www.file-up.org/xgwes1qf5iis
What happen to the tv? Why?
Very well done great job.
Say something!
i think 🤔 the video explain all
Salam repo apps, nice work and nice video with perfect explanation. I have exactly the same issue as you with a SAMSUNG UA49k6300AKXXA and PCB is BN41-02534B.
Do you think it is possible to have a copy of your dump for the EEPROM or to buy a flashed EEPROM directly? If so please tell me. Regards
it's the same bin file .. just try it .. first save your original dump then test my dump
@@repoapps Thank you so much
@@เบิกบาน_Channel Did it work ? I have a UE50H6400 with the same issue.
if it's the same eeprom just try
Vai Amar TV maje dak hoise ki vabe thik hobe
Very educational for technicians.thanks
You are welcome
hi ,
How to Fix TCL LED32S4900 Smart TV stuck On Start Screen Logo!
what is the chassis number of mainboard ?
@@repoapps 40-MT56S1-MAE2LG
Hi Reppo. I Tried to updated submicom feature in the service menu of my samsung smart Tv and messed it all. Guess what? Tv is dead. Not even standby light is on. I´ve heard one has to change the mother board or rewrite thesome eproom. Any hint? Thanks in advance
yes you need good dump for your eeprom tv , what's model you have ?
it is a samsung 40 smart tv model un4es6500
sorry i don't have dump for this model , if you can send me part number for your mainboard to search similar one
Hi Reppo. Mother board model is BN41- 01812.Thanks again.
very thankful for the video
Hallo there i have exactly the same problem how can i fix it can you be sweet and help me with it?
hello , you're welcome 😉, if you have the same problem and the same mainboard so reprogram the ic eeprom, you need programmer friend
@@repoapps hmm :( is not someone as ready you can buy or pay it from anywhere? if it is you can give me a link :)
buy programmer or the ic already programmed ?
@@repoapps ho can i buy that ? can you giv me one link pleas
the programmer like : sofi sp8 is not expensive.
Hola. Tengo un problema parecido en un UE32H4500AW desolde el ic901 lo reprograme con un archivo que se llamaba ue32h4500 donde tenía para flshear las dos memorias el ic1304 y el ic901 pues bien después de reprogramarlas la tv me muestra smart tv y acto seguido se queda la pantalla en azul. 😪 Ya no se que puede ser
what's the first problem? it's like on my video ? if yes so reprogram the ic with the original dump ( if you have save it before erasing it) .and see if the first problem come back .
@@repoapps She starts showing the Samsung smart tv logo and immediately stays on but with the black screen and the backlight works perfectly. It does not restart. I've already tried flshear both memories
It's like I didn't load the firmware
mainboard part number ?
@@repoapps UE32H4500AWXXC, BN94-07228C 01008731275
What if it has changed is the following. Before programming the two ics with the files corresponding to the ic901 and ic1304, the TV constantly rebooted. Now it only remains with the black screen and the Standby LED blinks 4 times. Thanks for your support
thanks!!!!
You
Bonjour,
Tout d’abord merci beaucoup pour cette excellente vidéo qui me permet de connaître l’origine de la panne de mon téléviseur.
C’est une TV Samsung eu UE48H6200 , et je ne suis malheureusement pas équipé pour pouvoir re flasher le composant, existe-t-il une autre solution ?
Si non, à combien estimez-vous le prix honnête de cette réparation par un professionnel ?
Merci pour votre aide.
Bien cordialement.
Hi, I have un46d6003sf that is stuck on the input screen right after the logo screen. can I use your eeprom file?
part number of mainboard ?
@@repoapps bn94-06429c
yes you can use it , but first save the original dump
@@repoapps Thank you! I'll try it.
@@repoapps I checked and I don't have 24C512 on the board but I have the 25Q64CVSIG. I managed to read and save it.
😊👍👌❤️
Vc tem o arquivo bin dessa tv que possa enviar? Minha tv é de 40 polegadas.Valew
link : www.file-upload.com/xgwes1qf5iis
you're welcome 😉
@@repoapps Hi there, can you please tell me where I can find the binary file for my Samsung ue55h6290ss?
Thanks for the great video.
And do I need to unsolder the chip for flashing? Or can I do it when is mounted?
Best regards.
Hey wear did you get the bin files from to flash back to the chip ? Thanks
And how to do it with out the programmer
link here : file-upload.com/d/EhXE
Is there another way to flash with out programmer?
no you can't
Sir how to ultraedt warking
please explain more
if i put a new eeprom it will works ?
must programming the new eeprom before use it
i do not have the eeprom programer can you suggest me a cheap programer to buy online and fix my tv ? and where i can find the program to reeprogram the eeprom ?
this's cheap programmer :
a.aliexpress.com/_B0pANr
the dump file you can find it in description
thank you from your respond , i bring the tv to a specialist and told me that the problem is tha main board ( bn94-074678g) told me around 200 euro to fix it . is it for sure the eeprom problem or should i have to chaing the whole board ( do you sale main board can you send me a new one to chaing it ? ) my tv is UE489H6800AWXXH . MAIN BOARD BN94-07467G . VESRION 1 THANK YOU FOR HELPING ME
Why not you try to flash its firmware?
Hi, I've got the same problem on UE50J5500AKXZT Samsung Smart TV... In your opinion is it possible to apply the same procedure to solve the fault? Thanks anyway
hola tenes el archivo bin de un46es6900 para enviar? excelente video
first search in your main board for eeprom s24c512 ic 8 pin ?
@@repoapps si la mainboard es similar. Usa la misma Eeprom 24c512 de 8 pin
@@repoapps probe varios archivos y sigue presentando el mismo problema que tienes el tu video, quisiera probar el archivo que usas para ver si funciona o descartar y buscar otra posible falla.saludos
test my file and tell me results
@@repoapps where is the file?
Sabía de la importancia de la pasta térmica color gris ubicada sobre el microprocesador de las PC. Te ví reemplazar la "goma azul" (disipador térmico 7:50) a la cual llegué a considerar un "estorbo" porque creí que había pasta similar debajo del disipador negro en el microconrolador. Muchas gracias por el "tip". Excelente trabajo de reparación. Un saludo desde México.
interesting video , thanks for help
Salam repo apps, nice work and nice video with perfect explanation. I have exactly the same issue as you with a SAMSUNG UE48H6200AW and PCB is BN41-02156A.
Do you think it is possible to have a copy of your dump for the EEPROM or to buy a flashed EEPROM directly? If so please tell me. Regards
Meinen sie das ?
drive.google.com/open?id=1UdlwRMGXMMffc9SHiwKVdJoJEEY9MUQL
@@dragonballsuperger9857 Thank you very much, I will test it. Best regards
Hi i tried your .bin. EEPROM flashed well but I still have an issue: i have an EDID fail in the service menu and i cannot navigate in the service menu to change the TV model. Any idea please? I can share pictures by email if needed. Thanks for your support