Setting the IP Address on a MicroLogix 1400
ฝัง
- เผยแพร่เมื่อ 2 ก.พ. 2017
- McNaughton-McKay's, Mike Brennan, explains how you can setup the IP Address on a Micrologix 1400. The video describes how to use the integrated keypad and LCD display to configure the IP Address, Subnet Mask and Gateway Addresses.
Website: www.mc-mc.com
Contact Us: 844-687-6262 or www.mc-mc.com/Locations
Subscribe on TH-cam: th-cam.com/channels/7RQ.html...
LinkedIn: / mcnaughton-mckay
Facebook: / mcnaughtonmc. .
Twitter: / mcnaughtonmckay
Blog: www.mc-mc.com/roller/blog/
Our videos are made available for your convenience and we hope you find them helpful. Please note, however, that the information contained in the videos is subject to our disclaimer and should not be relied upon as professional advice or services. We cannot overstate the importance of reviewing the national electric code and any pertinent local codes for approved installation, use, storage and repair procedures and precautions; failure to do so may result in property damage, injury or death. Always consult with your professional advisors to determine the products to suit your intended purposes.
LEGAL DISCLAIMER:
The text, sound, graphic, video and other information and
materials made available on our website (including but not limited through our resources center and video center) or by us through TH-cam or any other social media platform (all such information and materials referred to as “our information”) are provided voluntarily by McNaughton-McKay Electric Company “AS IS” and “AS AVAILABLE.” “Information” includes any comments we may make on any website or social media platform regarding any video or other materials. Information may change at any time, and McNaughton-McKay assumes no responsibility to provide updates or revisions. McNaughton-McKay disclaims all express and implied warranties with respect to information and to the products described, including implied warranties of non-infringement, merchantability and fitness for a particular purpose. Applicable law may not allow the above exclusion of implied warranties, so the exclusion may not apply, but shall apply to the maximum extent allowed by law. McNaughton-McKay cannot and does not represent or warrant that information will be error-free, up-to-date, comprehensive or complete, or otherwise meet your requirements, or those of your customers or business partners. Your use of our resource center, video library and of information is further subject to our website terms of use. Please visit the website terms of use at www.mc-mc.com/TermsofUse. - วิทยาศาสตร์และเทคโนโลยี
![เปิดบ้านสุดหรู "เเจ็ค the ghost" ลั่นถ้าป๋องกพลลำบากผมเลี้ยงเอง!! l [Nickynachat]](http://i.ytimg.com/vi/1xbW4vULqGc/mqdefault.jpg)
Thank you, but could you make a video of how the programme of the air compressor does function
Hi Hamza and thanks for reaching out. Your request is a topic where we would need a bit more information to provide a video response. Instead we suggest a conversation with your local sales representative or Rockwell Automation representative who can speak with you on your specific details and questions.
Sir, please is possible conect mgx 1400 to 2 cognex câmera and 1 hmi and 1 balluf inteligente i/o and 1 computer ?
Hello Arthur, This integration is quite tedious and at times not feasible. Assuming this is via Ethernet and not Serial:
Without having Cognex Part numbers, HMI part number, Balluf part number and what role the PC will play is nearly impossible to provide guidance.
Assumptions:
Over ethernet, one can setup or create explicit messages in the PLC logic that will allow the transmission of data between the PLC and Cameras.
Within the HMI application, creating a shortcut that points to the right tag or data point will need to be designed.
Lastly the Balluf IO will probably end up triggering the camera based on the presence of a part to then take a photo and then the data from the photo (pass/fail) will be sent over Ethernet to a data base or excel sheet which is on the PC.
Please reach out to your local Rockwell Automation distributor for further assistance. Thank you.
HI, could I used this PLC 1400 to connect a sensor to get air volume from a FAN, the capacity of the fan is 37,000 CFM, but I do not know if plc support this number (37,000)
The MicroLogix 1400 can support integer values from -32,768 to 32,767.
However, depending on the sensor used to read air volume, the CFM value may be represented differently and within the controller’s integer range. We would recommend contacting your local Rockwell Automation distributor to discuss your application and other possibilities.
@@mcnaughtonmckay thanks, I will check with the Distributor
Thanks.
Glad it was helpful!
Ok good information 👌🇮🇳🇮🇳🇮🇳
Hello, we're glad to hear you found the video helpful! Be sure to subscribe to our channel for more videos like this.
How can I do this on a MicroLogix 1100? I have used it on a router with a network ID: 192.168.1.XXX but now I want to use it on other area connected to another router with Network ID 10.237.81.XXX. It seems the PLC has stored the IP Address> 192.168.1.100 and I can not change it. I have try with BootP - DHCP Tool Software but since I can not connect the PLC to the new router this software doesn' recognize the PLC. Thanks for your help
Hi Joseph, Since the IP address of the MicroLogix 1100 was previously configured, we will need to change the IP address through RSLogix 500.
Your computer’s IP address will have to be set to match the previous area network.
You can change the IP address in the Channel Configuration menu of RSLogix 500 and download the change.
Please refer to the MicroLogix 1100 User Manual for more information, or reach out to your local Rockwell Automation Distributor.
literature.rockwellautomation.com/idc/groups/literature/documents/um/1763-um001_-en-p.pdf
@@mcnaughtonmckay Thanks for replying and your help. I will try this.
@@josephchristopherluttmannv9800 It's our pleasure. Best of luck!
can you do the same of 1100 unit?
Hi Maciek, Yes, the MicroLogix 1100 sets its IP address exactly like the MicroLogix 1400. If you have further questions or concerns, please reach out to your local Rockwell Automation distributor.
Sir, My micrologix 1400 ip address always changed after restarting the PLC.
Econfig is Static
Hello,
On the MicroLogix 1400 you'll want to make sure that DHCP is turned off after setting the IP address. This will prevent the IP address from resetting.
rockwellautomation.custhelp.com/app/answers/answer_view/a_id/495078/loc/en_US#__highlight
If you have further questions or concerns, please contact your local Rockwell Automation distributor.
Sir, what is the reason of Ip conflict?
Hello Ravinder and thanks for reaching out. When there is an IP conflict, typically the IP address you are attempting to set the Micrologix to is already in use on the network you are connected to. You might find this knowledgebase article helpful: rockwellautomation.custhelp.com/app/answers/answer_view/a_id/549521
come posso procedere per cambiare password non conoscendo quella attuale su un plc micrologix 1400 grazie?
Hello,
The default master password to edit the MicroLogix 1400 IP address via LCD display is "1234". Refer to the MicroLogix 1400 Programmable Controllers User Manual, 1766-UM001, Page 124 to 133 for more information:
literature.rockwellautomation.com/idc/groups/literature/documents/um/1766-um001_-en-p.pdf
Ciao,
La password principale predefinita per modificare l'indirizzo IP di MicroLogix 1400 tramite il display LCD è "1234". Fare riferimento al Manuale dell'utente dei controllori programmabili MicroLogix 1400, 1766-UM001, pagine da 124 a 133 per ulteriori informazioni:
literature.rockwellautomation.com/idc/groups/literature/documents/um/1766-um001_-en-p.pdf
Sir how to remove password
Hello, You can find step-by-step instructions for removing a password in this TechConnect Technote: rockwellautomation.custhelp.com/app/answers/detail/a_id/1081896/page/1
If you have any questions or concerns, please reach out to your local Rockwell Automation distributor. Thank you!