Unigraphics NX- Sketch Example 5 with constraints and Dimensioning for beginners

แชร์
ฝัง
  • เผยแพร่เมื่อ 27 ก.ย. 2024

ความคิดเห็น • 23

  • @TechDesignsantosh
    @TechDesignsantosh  3 ปีที่แล้ว

    Hi Guys
    I know there are 3 constraints left.. its because of construction just trim them you will have completely constrained sketch

  • @naveenprasath2796
    @naveenprasath2796 3 ปีที่แล้ว

    U rocking man.... Keep going

  • @Abhijeet_Hublikar
    @Abhijeet_Hublikar 3 หลายเดือนก่อน

    Bro, Can you share drawings for practice.

  • @tejsingh3000
    @tejsingh3000 5 ปีที่แล้ว +1

    When ever I am making a sketch there are always more than 15 or 20 constants. How can i fix all the constants.

  • @barnaltnsar6416
    @barnaltnsar6416 3 ปีที่แล้ว

    THX

  • @ashalatha9615
    @ashalatha9615 3 ปีที่แล้ว +1

    But it is still with 3 constraints

  • @ParthPatel-li8wu
    @ParthPatel-li8wu 2 ปีที่แล้ว

    From where did u got the centerline?

  • @sunilkumbar8186
    @sunilkumbar8186 2 ปีที่แล้ว

    How u drawn construction line (around 5 minut)

  • @saurabhroy7100
    @saurabhroy7100 ปีที่แล้ว

    6:01
    Is it the best practices to make that profile that way? Like if you make those outer same circles first then joined them with tangent straight lines and trim the unwanted lines, then you come to inner profile by just line offset. Don't you fill this make sense more?

  • @manojtomeet
    @manojtomeet 4 ปีที่แล้ว +1

    Sketch is not fully constrained

  • @aravvashisht4987
    @aravvashisht4987 ปีที่แล้ว

    I have a lab pratical tomorrow and have never touched this software. Wish me luck!!

    • @TechDesignsantosh
      @TechDesignsantosh  ปีที่แล้ว

      Wish you good luck 🤞

    • @saurabhroy7100
      @saurabhroy7100 ปีที่แล้ว

      Prepare this software, learn mold design/ BIW/ Trims interior/ Trims exterior any and ready for company right after your graduation. Thanks me later.

  • @arjunips1154
    @arjunips1154 ปีที่แล้ว

    Single sketch design in ug nx

  • @byeongmokJo
    @byeongmokJo 4 ปีที่แล้ว

    thank you for your video :)

  • @aryagodhani6568
    @aryagodhani6568 4 ปีที่แล้ว

    Thank you for video

  • @SufiyanAhmed
    @SufiyanAhmed 3 ปีที่แล้ว

    how did you make a construction line?

    • @TechDesignsantosh
      @TechDesignsantosh  3 ปีที่แล้ว

      Hold right click on any line you have options to make construction..

    • @ClashForTheWin
      @ClashForTheWin 3 ปีที่แล้ว +1

      right click on the line then convert to reference