I'm watching from Russia. It turned out funny)) But, for a novice specialist, this will do! )) Author do you know what a "Datasheet" is?? Maybe you've heard about it? )) And why do you write at 3:50 minutes that this device can work on 5-60 DC?? Why did I try it myself only up to 16 DC )) And even at the same time, there was smoke from the chip. She began to burn. I'll tell you a little secret )), when you connect a motor to this circuit, you definitely need to put a powerful diode parallel to the motor. Because the excitation from the brush assembly of the engine is very powerful. And this tension will kill the mosfet. . Смотрю из России. Смешно получилось )) Но, для начинающего специалиста, такое сгодится! )) Автор ты знаешь что такое "Datasheet" ?? Может слышал про такое? )) И почему ты пишешь на 3:50 минуте, что это устройство может работать на 5-60 DC?? Почему сам попробовал только до 16 DC )) И даже при этом, пошёл дым от микросхемы. Она стала гореть. Скажу тебе небольшой секрет )), когда к этой схеме подключаешь мотор, то обязательно нужно ставить мощный диод, параллельно мотору. Потому что, возбуждение от щёточного узла двигателя, очень мощное. И это напряжение убьёт мосфет.
@@homemade_101 How? If you put 15V into the input, you can output 10V, but without a boost circuit, you won't output 24V, if you have 15V input! I don't see any coils in your montage! The output voltage will never be higher than the input voltage!!! Never !!!! 😕
@@homemade_101 Brother, but you really don't know anything ? You cannot output 60 V even if you have 60 V at the input! Once you exceed 15V, the 555 will burn out! So, when you increased the voltage to 18 V, you will have 0 V on the output, not 18 V. Stop making videos if you don't know how work !!! 😕
You don't understand anything! This is an Indian movie! And he, the good wizard, is from the land of elephants and tea! Don't tell him about volts and amps, they don't do that! And "Datasheet" is a swear word for them... . Ты ничего не понимаешь! Это индийское кино! А он, добрый волшебник, из страны слонов и чая! Не говори ему про вольты и амперы, у них так не принято! А "Datasheet" - у них это ругательство...
50A voltage controller 👉th-cam.com/video/j3E9Hj31ZHg/w-d-xo.html
Creative idea ❤️
Thank you and welcome 🌀
I note in your video the skitch include two output kindly I ask you where is the input regards
So cool and nice
Welcome
I'm watching from Russia.
It turned out funny))
But, for a novice specialist, this will do! ))
Author do you know what a "Datasheet" is??
Maybe you've heard about it? ))
And why do you write at 3:50 minutes that this device can work on 5-60 DC?? Why did I try it myself only up to 16 DC )) And even at the same time, there was smoke from the chip. She began to burn.
I'll tell you a little secret )), when you connect a motor to this circuit, you definitely need to put a powerful diode parallel to the motor. Because the excitation from the brush assembly of the engine is very powerful. And this tension will kill the mosfet.
.
Смотрю из России.
Смешно получилось ))
Но, для начинающего специалиста, такое сгодится! ))
Автор ты знаешь что такое "Datasheet" ??
Может слышал про такое? ))
И почему ты пишешь на 3:50 минуте, что это устройство может работать на 5-60 DC?? Почему сам попробовал только до 16 DC )) И даже при этом, пошёл дым от микросхемы. Она стала гореть.
Скажу тебе небольшой секрет )), когда к этой схеме подключаешь мотор, то обязательно нужно ставить мощный диод, параллельно мотору. Потому что, возбуждение от щёточного узла двигателя, очень мощное. И это напряжение убьёт мосфет.
Thank you very much brother for this comment
@@S_e_r_g_ei ne555 should not be supplied by more than 15 V i think. Check ne555 manual first for voltage supply valie
Hello friends me ic pcv board Kaha se khareeb Karo China se agir kio important ka pata bati
Can you want to buy this ic?
Can a pmw module control 12v 5amp heating element...?
try this is th-cam.com/video/CK0MXyzSEPo/w-d-xo.htmlsi=gr3OvXM3dTfi6vG2
Why does your work not reflect the same as the diagram? The connections are different and you use a 1K resistor instead of a 200 like in the diagram
Can we use 60v 3ah adapter??
Can we use????
Is there feedback
no. this is feedback: th-cam.com/video/6kdCtOZ0w0c/w-d-xo.htmlsi=3JLDdKTpVjpgb4nF
ne555 max voltage 18v ?
Not ! 15 V is maxim voltage !
Will it not be heated?
it is normal
Why did you name this clip 0-60V?
With CI 555, you cannot exceed 15 V voltage !
My power supply input 15v. But you can adjust 60v maximum
@@homemade_101
How?
If you put 15V into the input, you can output 10V, but without a boost circuit, you won't output 24V, if you have 15V input!
I don't see any coils in your montage!
The output voltage will never be higher than the input voltage!!!
Never !!!! 😕
@@John_Smile yes, If you can input 60V you can get 0-60V out.
@@homemade_101
Brother, but you really don't know anything ?
You cannot output 60 V even if you have 60 V at the input!
Once you exceed 15V, the 555 will burn out! So, when you increased the voltage to 18 V, you will have 0 V on the output, not 18 V.
Stop making videos if you don't know how work !!! 😕
You don't understand anything!
This is an Indian movie!
And he, the good wizard, is from the land of elephants and tea!
Don't tell him about volts and amps, they don't do that!
And "Datasheet" is a swear word for them...
.
Ты ничего не понимаешь!
Это индийское кино!
А он, добрый волшебник, из страны слонов и чая!
Не говори ему про вольты и амперы, у них так не принято!
А "Datasheet" - у них это ругательство...
Is it a pwm speed controller?
yes
👌👌👌
😍
👉👏👏👊👊❤️❤️👍👍👈
Main reason it burnt was applying too much voltage max volt is 15V and safe volt is 12
Whats the max output current?
10A max
Ваша схема собрана неправильно, поэтому и микросхема сгорела дым пошел, вы горе мастер и желаете кого-то научить😢😅😮
Luar negri
Your explanation in you video not match any more the Skitch in the video please upload new Skitch match with your video explanation thanks
Your pot is upside down
👍
Luar negri