His activated charcoal needs to be crushed into a powder first. The other thing he needs to do is to alternate the materials 3-5 times in order to filter out biological agents and other smaller compounds like the newer chemical agents. While not fool proof (only a closed system is completely fool proof, and even then its iffy) it could help increase the protective agency of the mask.
IMPORTANT!!! WATERTIGHT IS NOT THE SAME AS AIRTIGHT!!! Air molecules are smaller then water molecules and there a mask can be watertight but not airtight. Air tight IS water tight Watertight IS NOT airtight
You want P3 filters for corona-protection, P3R D preferably. And yes, they are still available in some places. Ordered and received a box of dirin 230 p3r d filters from germany last week, at a reasonable price too.
For all the commenters who say “you can get a military grade gas mask for under that” yes, that is true. BUT, this video was probably for the fun of making it yourself and testing it out.
This really dumb way to do this though . You could make a simple silicon rubber plug for the snorkel, drill hole for the filter on the side instead of front and keep the outlet valve. It would be easier to breath in and out and you could still use it for snorkeling, just plug the air intake hole with a screw cap. Or just fill the snorkel with charcoal and be done with it.
@@MechNinji that air buble out part of mask perfectly fits for a gas mask but i have a another idea that part for fits too for carbon dioxide out part u put filter to under water air part and out carbon dioxide to out air part is a better idea i think btw sorry for bad english
That soft "white rubber" disc you removed to make the attachment point for the filter should have been kept as an exhilation valve, otherwise you are breathing both in *AND* out through the filter material. I would suggest using a 60mm mask to 40mm filter adapter, glued into a new hole either above or to one side of the exhilation valve and using that to attach a filter.
@@sbrim30 No, just so there is something with a NATO 40mm thread to glue onto a new hole, so that standard filters can be used. 60 to 40 adapters are just a conveninet piece of hardware to do that with.
Robert Mackrell If you’re in the Army, then you know about your M40-A1 promask. So why are you comparing this homemade snorkel mask to a $400 military grade mask?
Under 30 bucks you can also buy a Russian GP- 5, that will be reliable, (ten bucks) and a Polish FP-5 filter (10- 15 bucks) and you have a gasmask that *will* actually be reliable and *will* save your life! *DO NOT USE THE FILTERS THE GP- 5 COMES WITH! THEY CONTAIN AZBESTOS!* But this is quite cool for a scavenger cosplay.. If you are going to make this, crush the activated charcoal, it will be more effective :)
That one way valve you literally cut out of the mask.. would have actually been incredibly helpful to the mask. As the valve allows air out of the mask, without allowing air back in and ruining the seal of the mask.
@Sean Sigmund Its foolish. If you want to breath out easier and not have the mask fog up, you don't destroy an industrial made exhale valve. Its a waster of good craftsmanship.
Also, with the filter, you probably smelt a little spray because the activated charcoal/carbon wasn't fine enough, the pelts are big and leave a lot of space, you can buy finer activated charcoal in the pet store, that would be better for a mask, or if they don't have it you can just grind the big pellets a little to make the filter work a bit better, just some friendly advice, anyway great video and great mask too.
with an exhale valve and a little more care on the filter , ie make a better particle filter and crush and pack the charcoal this could be a serviceable mask , heck you could even add a drinking tube ! good stuff
Very creàtive build, I would recommend layering the filtering system as a t-shirt layer on the 1st layer of the filter, a sponge as the 2nd layer, 1/2 activated charcoal, card board layer covered in holes, 1/2 layer charcoal, another card board layer covered in holes then cotton balls. When testing any home made gas mask use a road flare burning in a pot. If you can't smell it or choke while breathing in ur gas mask works. Sgt. Anthony Har
Creative? Rather it is to complicate life. With that money I would buy a gp5, a Soviet clone of the m9 mask, a Yugoslav mask. Waste of time for a dysfunctional artifact.
problem is those cotton ball-made filter does not meet the safety standard as P100 filter.... you need filter that can block those particulate that carry the COVID19... u dont need active charcoal, those are for absorb harmful gas...
@@yipfred1751 use a merv 16 hvac filter they filter to 0.3 microns at 95% efficiency they aren't cheap though but last for a year and you could get multiple filters from one unit cost around $95 at Walmart
I live in Philadelphia PA, riots and gas are a major concern right now. Thank you for showing me how I can attempt to keep my family safe without spending almost $1000
am i missing something here???? u cut off the inhale hole at the top and blocked it off. then changed the original exhale hole on the front to an inhale hole with the filter... now u have no exhale hole.... so the mask dosnt work at all.......
It does work however you risk inhaling too much CO2 because there's no way for "used up" air to escape the mask other than the filter. So that CO2 will stay in the filter after you exhale and then be inhaled again, and again, and again, which can kill you. Some older masks didn't have exhale valves because they were usually civilian and used for evacuation so not for a long period of time.
One criticism on your mask is mounting the filter directly on the mask. I'm ex military an this type of mask gets real uncomfortable when you have to wear it for an extended time. A much better option would be using a 40mm tube to connect the mask to the filter, ie like the ww1 type masks. It not only takes the weight off your head and neck but let's you use a much larger filter than you could mount to the mash itself. I would not close off the top port either but instead convert it to N exhaust only port like military masks have. I doubt you could even get a civilian version mask for the same cost as what it would cost to make one. That I would have to see proven. Plus military masks have much more restrictive vision than does the mask you demonstrated. Using plastic weld instead of glue is also a better option. It bonds the two pieces into a single part. Hell they use it to build aquariums that hold back hundreds of pounds, using it to make a filter housing would be easy, although it does take 72 hours to fully cure. Additionally I don't think any of us plan to go to war in this mask so it does seam a reasonable use for chemical fumes and dust. Besides it looks like a blast to build anyway. Lol
Just one question, how is air supposed to get out? If you want it to go back trough the filter there would be co2 buildup Also you could buy a lot of surplus gas masks,adaptors (for gost or 60mm gas masks) and a m80 israeli filter (even in date le you search hard enough) for the same price
Because you cant buy an "actual" gas mask for less than $20. At least not one anywhere close to the same quality. You could buy a few paper dust masks though, if that's what you mean.
Mechanical Ninjineer yes you can. rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F263415407418 it has an asbestos filter but for an extra 15 bucks you can get a NBC filter without asbestos and those filters last hours. You could use the asbestos one too in an emergency
Mechanical Ninjineer we know for a fact it has asbestos but if the filter isn't damaged it will work and probably not leak and even if it does short term asbestos exposure is way less serious than most gasses that you would need a mask for.
I have the gd5 but this have a bigger lense to look out from. With the gd5 we could use the Poland filter. It's like $15 on eBay. But I'm going to make your diy gas mask. Much more view to see.
1:48 you shouldnt have done that. just reverse the valve to make it an intake valve. and then make the intake at the top your exhale valve. also to increase efficiency, crush the grains of charcoal. and your particle layers should be a bit thicker and/or made from M3's particle filters. you can get packs of them from walmart
this guy didn't make one, but i was thinking that the top part from the scuba mask that he took off and sealed up may be made to be a one way valve so that you could exhale through it
David Kermes He has to make the mask more fashionable. I saw a similar video where a prepper used that same snorkel device, but he instead used the snorkel valve. It looked really weird... and honestly it probably would not have been that much more effective than this design.
Very cool idea I might try this. There is a couple of problems though. First, that rubber valve you removed from the mask is the exhale valve. You need that in order to efficiently breath out of the the mask. If you remove it, you'll end up having co2 build in the mask because your breath has to work its way back through the filter medium. Second, cotton is a poor choice for the main particulate layers. You need to use some sort of hepa filter (I recommend cutting part of a furnace filter). Make sure the MERV rating is at least 1900. This is because some cheaper filters will be made of fiberglass and breathing in fiberglass particles is a no no.
ORANG BOI I thought HEPA wasn’t affective for protective masks? Isn’t that why mask manufacturers use ULPA filters? Because U15 ULPA is capable of filtering 99.997
@@Blyegh Interesting, I looked at the packaging for those furnace filters and the higher tier ones say they can filter viruses and bacteria. It could be that they don't filter as good as other materials though.
ORANG BOI From what I’ve heard, while it’s effective for filtering out particles it’s only good to an extent. In a situation where we don’t have proper protective masks and only have limited resources to use, I guess it’s better than nothing at this point. But I wouldn’t heavily rely on a HEPA filter because it doesn’t filter out all of the smaller particles. U15 - U17 ULPA filters are capable of filtering out 99.997+, because ULPA filters are specifically designed to filter out nearly 100% particles that are 0.3 microns. I’d be interested in seeing anything else that could prove me wrong. I could definitely use that sort of information right about now hahaha
Do you have any suggestions to make the exhale chamber, i orderd the same mask as him as a fun little learning project… but I’ve gotten pretty seirous with it considering that it can save a life… I was thinking put the filter at the top of the mask wear air originals comes through, any thoughts on how I can do it?
@@the_goat_himself2541 The mask in the video already had an exhale valve, that's the hole that @MechNinji butchered to put his filter mount on. A better solution might be drill a hole in the clear plastic to one side of the mouth/nose cup and mount a filter there instead, that way breathing out goes straight through the valve and breathing in comes through the filter.
I’m thinking about filling the mask’s tube with granules of activated charcoal(used in aquarium filters) and some wadding and making 2 holes on the walls in the internal bottom of the tube to join all the 3 sections of the tube and use them as “air in”, and to effectively make the tube an actual reusable antigas filter. And maybe also use part of a vacuum cleaner’s sack (which usually block particles as little as 30 micron) to seal the top. Would it be good?
That would be awesome! I'm thinking about doing this for Arkansas if my personal one works out. I'm tired of watching everyone there be fired upon. 99% of us have been peaceful with a clear distinction between those who want to escalate and those who don't. I totally understand why people are engaging in less peaceful behaviours. Our local black leaders of the movement call for peaceful protests for now, so that's what we're trying to help them enforce. But they fire on the peaceful people anyway and we need some gas masks.
No it's not, do not trust your life on that, he made it for a fun video, use a half-face 3m respirator or buy a gas mask (make sure its the right size for you). If you get an old Russian gas mask (gp-5, gp-7) buy a new filter for them like a polish FP-5 filter. If you want more info for gas masks go visit the channel Weaponsandstuff93. Have a good day, stay safe :D
Emergency only. I'd say CS (military style tear gas), and some larger nerve agents are what its designed to protect against. It's not for long term use, so it should be used exclusively to GTFO of the area.
Unused? I'm not sure if there really is much of a limit as long as its sealed in an air tight container. But if you do use it, you'll prob want to replace it after every use, just to be safe.
What if we have no snorkling mask....can you sir make a video of diy and around the house things like plastic bottles....we really need your help....FROM PHILIPPINES
5:33 looks like DEET bug repellent.... thats the good stuff. lol I got my finnish gas mask... I think they are still fairly cheap too. but I might would have flipped the "exhale" valve so you only get intake through the filter... then some sort of cobbled together valve for exhale gasses.
if you’re talking about CHKadels or BUDK from the United states they list them as Polish MP5s but they’re actually a French ARFA. you can tell the difference easily because the french have holes in the voice diaphragm not the front and the Polish have circular lines
My suggestion is that the activated charcoal sould have been crushed lightly, because the center of the pellet is useless oherwise and is wasted overall great video
I saw your video because I am trying to make a mask for the corona virus. However I don't get your solution at all. You sealed the upper exhausts and breath in through the lower exaust. Where will the air go now? Back through the filter? This is not how gas masks, respirators or any masks work at all.
I mean you can buy a GP5 gas mask for roughly £10 and then a new modern filter for £10 so you could buy a real mask with a working filter cheaper. Still a great video though.
@@ItsSamHussey I forgot to mention that it's according to the location. Sorry for the misclassification. Here in Malaysia, TF-1 is the cheapest. Cheaper than a typical 3m respirator.
love your vid but i didnt use the can i used the 2 side half gas mask refillable filter only 6$ and glued the half gas mask into the full face mask snorkeling
I've a school prjct which is i need to make something that can reduce air polution . Do y think i can make ths ? Ahahahaha im just afraid ppl can't breathe once they using ths . Please give me some opinion ?
that air buble out part of mask perfectly fits for a gas mask but i have a another idea that part for fits too for carbon dioxide out part u put filter to under water air part and out carbon dioxide to out air part is a better idea i think btw sorry for bad english
You could have bought a real gas mask for the same price or maby cheeper and it would be more effective and there would be filters specifically for the mask instead of having to build one every time also it would just be more reliable
You can very well get a “military grade” gas mask for waaay less than a couple hundreds. Get ANY Chinese mask for example, plus like 10 to 20 dollars per regular Nato filters, BOOM perfectly working, new gas mask.
I’m just going to throw these two things out there, 1 ninjanear might have been able to smell the stuff he sprayed in the trash can because he may have not had a proper seal on the mask because of his beard. 2 military grade actually is worse than civil stuff, go civilian any time you can because it’s better.
Cyborg2101 that is the most retarded thing I have ever heard, nearly all civilian masks you can get that even come to close to even cold war military gas masks would be a fireman's air supplying respirator
Cyborg2101 no but I have experience with military gas masks and civilian ones. And I know a few people from the military and I know what gas mask they use. Civilian gas masks are a rip off 90% of the time because surplus military gas masks tend to be cheaper and higher quality than a civilian gas mask. And I garuntee that there is no civilian gas mask that you could show me that is better than a cheaper surplus military mask.(except maybe the isreali 4a1 but many people say it's uncomfortable)
_ISO_ well as one who is in the military I can promise the military ones are not as good as civilians think. Remember the government is buying them from the lowest bidder.
Wrong connector for shtf, you should put a pet bottle cap on the intake and use 600ml pet bottles, they are very easy to manufacture and have a lot more air travel and surface area in the lightest package possible.
AS a former service man who worked with NBC and similar in employment, great but, the one way valve should have been left and just tap a 40mm for your filters in case you run across reg. filters, place a secondary filter cover over said one way valve, after you spend hours in it or it fills with condensation sweat or clouds up in firefight, learn to make better than those $200+ models, and learn how to use these... technologies
I would like to make one, probably already made, complaint in that you shouldn't have painted the mount before gluing it in place, as that creates a point where it can fail very easily
Me seeing this in 2018:
“Lame”
Me seeing this during Coronavirus:
*watches intently*
His activated charcoal needs to be crushed into a powder first. The other thing he needs to do is to alternate the materials 3-5 times in order to filter out biological agents and other smaller compounds like the newer chemical agents. While not fool proof (only a closed system is completely fool proof, and even then its iffy) it could help increase the protective agency of the mask.
IMPORTANT!!! WATERTIGHT IS NOT THE SAME AS AIRTIGHT!!!
Air molecules are smaller then water molecules and there a mask can be watertight but not airtight.
Air tight IS water tight
Watertight IS NOT airtight
SCORPION FIRE You can’t buy them on Amazon anymore.
letting you know those filters are not good against coronavirus
You want P3 filters for corona-protection, P3R D preferably. And yes, they are still available in some places.
Ordered and received a box of dirin 230 p3r d filters from germany last week, at a reasonable price too.
For all the commenters who say “you can get a military grade gas mask for under that” yes, that is true. BUT, this video was probably for the fun of making it yourself and testing it out.
Yes but the title of the video does not say so.
sun-dye
I cant find a military grade for cheap anywhere
And to keep you off radar or if they are sold out
This really dumb way to do this though
.
You could make a simple silicon rubber plug for the snorkel, drill hole for the filter on the side instead of front and keep the outlet valve. It would be easier to breath in and out and you could still use it for snorkeling, just plug the air intake hole with a screw cap.
Or just fill the snorkel with charcoal and be done with it.
This is the first homemade gas mask I've seen which has an interchangeable filter, which is good. So yay.
haha! I'm glad you like it! :D
SaavageTurtle 41 it looks cool but it will kill you if you use it
its good if you like dying
@@nine552 well, I'm still alive
@@MechNinji that air buble out part of mask perfectly fits for a gas mask but i have a another idea that part for fits too for carbon dioxide out part u put filter to under water air part and out carbon dioxide to out air part is a better idea i think btw sorry for bad english
That soft "white rubber" disc you removed to make the attachment point for the filter should have been kept as an exhilation valve, otherwise you are breathing both in *AND* out through the filter material. I would suggest using a 60mm mask to 40mm filter adapter, glued into a new hole either above or to one side of the exhilation valve and using that to attach a filter.
That is so right, first thing I thought is why is he destroying the exhaust valve.
So you need a 60mm for a 40mm?
@@sbrim30 No, just so there is something with a NATO 40mm thread to glue onto a new hole, so that standard filters can be used. 60 to 40 adapters are just a conveninet piece of hardware to do that with.
@@dj1NM3 thank you
You took the words from my mouth... or rather my fingers
It's only airtight on people WITHOUT facial hair under the seal.
why
I've heard you can cover your beard in vaseline and still get an airtight seal.
@@joshpup1580 because the hair make small gaps between the mask and your face
Sounds logical right?
@@professionalschizo What masks does your army have?
Robert Mackrell
If you’re in the Army, then you know about your M40-A1 promask. So why are you comparing this homemade snorkel mask to a $400 military grade mask?
Under 30 bucks you can also buy a Russian GP- 5, that will be reliable, (ten bucks) and a Polish FP-5 filter (10- 15 bucks) and you have a gasmask that *will* actually be reliable and *will* save your life!
*DO NOT USE THE FILTERS THE GP- 5 COMES WITH! THEY CONTAIN AZBESTOS!*
But this is quite cool for a scavenger cosplay.. If you are going to make this, crush the activated charcoal, it will be more effective :)
Sense I’m stuck in China this will be real helpful
what gas mask should I purchase if I don't mind the cost?
JeanAlesiagain3 Get a Isreali M15
@@JeanAlesiagain3 Avon S10/FM12 (pretty much the same mask, FM12 is just an updated and better S10
@@JeanAlesiagain3 CM-6M Gas Mask
That one way valve you literally cut out of the mask.. would have actually been incredibly helpful to the mask. As the valve allows air out of the mask, without allowing air back in and ruining the seal of the mask.
It's one way for water but not necessarily for gas I'd imagine
yeah it would have been better if he were to screw on that air filter thing on top of the mask, although that wouldn't be so unconvinient to use
Keep the exhalation valve and add a separate hole for the filter canister.
I know, this guy knows nothing about respirators. To destroy a perfectly good exhale valve.
@Sean Sigmund Its foolish. If you want to breath out easier and not have the mask fog up, you don't destroy an industrial made exhale valve. Its a waster of good craftsmanship.
@Sean Sigmund You need to learn about respirators. That needs to happen first before you comment.
@Sean Sigmund makes it worse because you won't about carbon dioxide
hazmat unit there’s no intake valve so it comes through the filter and goes out through the filter and it has a nosecup to stop it from fogging up
Also, with the filter, you probably smelt a little spray because the activated charcoal/carbon wasn't fine enough, the pelts are big and leave a lot of space, you can buy finer activated charcoal in the pet store, that would be better for a mask, or if they don't have it you can just grind the big pellets a little to make the filter work a bit better, just some friendly advice, anyway great video and great mask too.
Yes, the sounds like it would help quite a lot! Good idea! That is definitely something I'm going to have to try! :D
could you use charcoal powder?
with an exhale valve and a little more care on the filter , ie make a better particle filter and crush and pack the charcoal this could be a serviceable mask , heck you could even add a drinking tube ! good stuff
Very creàtive build, I would recommend layering the filtering system as a t-shirt layer on the 1st layer of the filter, a sponge as the 2nd layer, 1/2 activated charcoal, card board layer covered in holes, 1/2 layer charcoal, another card board layer covered in holes then cotton balls.
When testing any home made gas mask use a road flare burning in a pot. If you can't smell it or choke while breathing in ur gas mask works.
Sgt. Anthony Har
Creative? Rather it is to complicate life. With that money I would buy a gp5, a Soviet clone of the m9 mask, a Yugoslav mask. Waste of time for a dysfunctional artifact.
Corona virus is spreading and this vid is now in my recommendations 😂😂
Let justice prevail
Came here to make one but i decided to buy a gas mask for 50 dollars cause its so hard
problem is those cotton ball-made filter does not meet the safety standard as P100 filter.... you need filter that can block those particulate that carry the COVID19... u dont need active charcoal, those are for absorb harmful gas...
@@yipfred1751 use a merv 16 hvac filter they filter to 0.3 microns at 95% efficiency they aren't cheap though but last for a year and you could get multiple filters from one unit cost around $95 at Walmart
@@matolittleelkwells5377 or get a filter that does more (which you can) for the same price or less
I live in Philadelphia PA, riots and gas are a major concern right now. Thank you for showing me how I can attempt to keep my family safe without spending almost $1000
am i missing something here????
u cut off the inhale hole at the top and blocked it off.
then changed the original exhale hole on the front to an inhale hole with the filter...
now u have no exhale hole.... so the mask dosnt work at all.......
It does work however you risk inhaling too much CO2 because there's no way for "used up" air to escape the mask other than the filter. So that CO2 will stay in the filter after you exhale and then be inhaled again, and again, and again, which can kill you.
Some older masks didn't have exhale valves because they were usually civilian and used for evacuation so not for a long period of time.
One criticism on your mask is mounting the filter directly on the mask. I'm ex military an this type of mask gets real uncomfortable when you have to wear it for an extended time. A much better option would be using a 40mm tube to connect the mask to the filter, ie like the ww1 type masks. It not only takes the weight off your head and neck but let's you use a much larger filter than you could mount to the mash itself.
I would not close off the top port either but instead convert it to N exhaust only port like military masks have.
I doubt you could even get a civilian version mask for the same cost as what it would cost to make one. That I would have to see proven. Plus military masks have much more restrictive vision than does the mask you demonstrated.
Using plastic weld instead of glue is also a better option. It bonds the two pieces into a single part. Hell they use it to build aquariums that hold back hundreds of pounds, using it to make a filter housing would be easy, although it does take 72 hours to fully cure.
Additionally I don't think any of us plan to go to war in this mask so it does seam a reasonable use for chemical fumes and dust. Besides it looks like a blast to build anyway. Lol
I'm watching this video because both of my older brothers did a "gas attack" on me and my little brother.
Your brothers like to fart in your general direction, eh?
Great video! Just a question, is there an exhale valve so you can’t suffocate?
This is awesome and actually really useful
i'm so happy i found this video, i have been having a hard time with my allergies. now i can go out side more often
Just one question, how is air supposed to get out? If you want it to go back trough the filter there would be co2 buildup
Also you could buy a lot of surplus gas masks,adaptors (for gost or 60mm gas masks) and a m80 israeli filter (even in date le you search hard enough) for the same price
How hard was it to breathe with the mask on?
Why would you wanna do this when you could by an actual gas mask for less than 20 bucks?
Because you cant buy an "actual" gas mask for less than $20. At least not one anywhere close to the same quality. You could buy a few paper dust masks though, if that's what you mean.
Mechanical Ninjineer yes you can. rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F263415407418 it has an asbestos filter but for an extra 15 bucks you can get a NBC filter without asbestos and those filters last hours. You could use the asbestos one too in an emergency
That's a GP-5. There has been some debate about weather or not the filters are safe for use.
Mechanical Ninjineer we know for a fact it has asbestos but if the filter isn't damaged it will work and probably not leak and even if it does short term asbestos exposure is way less serious than most gasses that you would need a mask for.
I have the gd5 but this have a bigger lense to look out from. With the gd5 we could use the Poland filter. It's like $15 on eBay. But I'm going to make your diy gas mask. Much more view to see.
in a real tim scenario, that little something you smelled, just killed you. Nice Toy ! well explained.
You can use the filters used for home ac filter
Ok but will this help me not breath in the tear gas at protests
thanks bro cause millitary gaz mask are prohibited here in france
Me seeing this in 2018: no thanks ||||| me seeing this in June 2020: can’t wait to stop choking on tear gas ✨💗⚡️🧚🏼
this is a joke I fully understand it’s not a CBRN filter
@RandomHoboLivingintheForest *you should protect yourself while protesting. fixed it for ya.
Isomatte I didn’t riot and still got tear gassed you raging buffoon
who is here after hearing about the Corona Virus?
Blendi Klimenta me
Me
I’M LITERALLY STUCK IN CHINA
Unknown Unknown Damn, be safe bro. Hope you make it back🙏🏼
@@blendiklimenta6657 I'm Trying to make mine now that Egypy is the First Contury In Africa to have the Coronavirus.
Nah shit
1:48 you shouldnt have done that. just reverse the valve to make it an intake valve. and then make the intake at the top your exhale valve. also to increase efficiency, crush the grains of charcoal. and your particle layers should be a bit thicker and/or made from M3's particle filters. you can get packs of them from walmart
please show us how to bolt the cup to the mask. bolts look very long. What do they screw into?
Can you still swim with this?
No, the water will come right through the filter. Unless of course you have a cap you can put on it.
Rufus no
I think the.. the... green Alien ate him for helping humanity....
Elementary question....How does the expelled air (from your lungs) get out of the mask? Thanks
this guy didn't make one, but i was thinking that the top part from the scuba mask that he took off and sealed up may be made to be a one way valve so that you could exhale through it
Wouldn't it have been simpler to use a flex tube to connect a filter to the original snorkel opening?
It probably would be, but you may not get enough air once the filters are in place.
David Kermes He has to make the mask more fashionable. I saw a similar video where a prepper used that same snorkel device, but he instead used the snorkel valve. It looked really weird... and honestly it probably would not have been that much more effective than this design.
Is this one safe, dosent contain chemicals??
it would why dong ding ding don't hey
I mean the filter its self is safe its only activated charcoal doctors make people eat it in a OD situation.
Good tip!!
Make the first layer instead of cotton use your mouth mask preferebly your ffp2 or ffp3 class mouth masks ( the ones the hospital uses)
Very cool idea I might try this. There is a couple of problems though. First, that rubber valve you removed from the mask is the exhale valve. You need that in order to efficiently breath out of the the mask. If you remove it, you'll end up having co2 build in the mask because your breath has to work its way back through the filter medium. Second, cotton is a poor choice for the main particulate layers. You need to use some sort of hepa filter (I recommend cutting part of a furnace filter). Make sure the MERV rating is at least 1900. This is because some cheaper filters will be made of fiberglass and breathing in fiberglass particles is a no no.
ORANG BOI I thought HEPA wasn’t affective for protective masks? Isn’t that why mask manufacturers use ULPA filters? Because U15 ULPA is capable of filtering 99.997
@@Blyegh Interesting, I looked at the packaging for those furnace filters and the higher tier ones say they can filter viruses and bacteria. It could be that they don't filter as good as other materials though.
ORANG BOI From what I’ve heard, while it’s effective for filtering out particles it’s only good to an extent. In a situation where we don’t have proper protective masks and only have limited resources to use, I guess it’s better than nothing at this point. But I wouldn’t heavily rely on a HEPA filter because it doesn’t filter out all of the smaller particles. U15 - U17 ULPA filters are capable of filtering out 99.997+, because ULPA filters are specifically designed to filter out nearly 100% particles that are 0.3 microns. I’d be interested in seeing anything else that could prove me wrong. I could definitely use that sort of information right about now hahaha
Do you have any suggestions to make the exhale chamber, i orderd the same mask as him as a fun little learning project… but I’ve gotten pretty seirous with it considering that it can save a life… I was thinking put the filter at the top of the mask wear air originals comes through, any thoughts on how I can do it?
@@the_goat_himself2541 The mask in the video already had an exhale valve, that's the hole that @MechNinji butchered to put his filter mount on.
A better solution might be drill a hole in the clear plastic to one side of the mouth/nose cup and mount a filter there instead, that way breathing out goes straight through the valve and breathing in comes through the filter.
I’m thinking about filling the mask’s tube with granules of activated charcoal(used in aquarium filters) and some wadding and making 2 holes on the walls in the internal bottom of the tube to join all the 3 sections of the tube and use them as “air in”, and to effectively make the tube an actual reusable antigas filter. And maybe also use part of a vacuum cleaner’s sack (which usually block particles as little as 30 micron) to seal the top. Would it be good?
If you want to block coronavirus use a HEPA vacumn filter .Has to be smaller than 1 micron
I heard that if you fill the inside with carbon monoxide first it helps you breathe better
lmfao
I tried it and it works!
-i have lung cancer tho-
Tested. Approved. 😵
ok guys im going to make these and send them to Minnesota
That would be awesome! I'm thinking about doing this for Arkansas if my personal one works out. I'm tired of watching everyone there be fired upon. 99% of us have been peaceful with a clear distinction between those who want to escalate and those who don't. I totally understand why people are engaging in less peaceful behaviours. Our local black leaders of the movement call for peaceful protests for now, so that's what we're trying to help them enforce. But they fire on the peaceful people anyway and we need some gas masks.
This is really useful during the coronavirus outbreak
No it's not, do not trust your life on that, he made it for a fun video, use a half-face 3m respirator or buy a gas mask (make sure its the right size for you). If you get an old Russian gas mask (gp-5, gp-7) buy a new filter for them like a polish FP-5 filter. If you want more info for gas masks go visit the channel Weaponsandstuff93. Have a good day, stay safe :D
@@big_bob_s3747 I know, there's no way I'd wear something home made 😂
@@sphinx2077 ok good😂I was just making sure. stay safe out there
@@sphinx2077 unfortunately alot of people will have to.
is the lense made from a type of silicone? some gasses can eat through silicone
Emergency only. I'd say CS (military style tear gas), and some larger nerve agents are what its designed to protect against. It's not for long term use, so it should be used exclusively to GTFO of the area.
can this prevents smoke entering your body?
Only if you put a large plug in your asshole.
How long can you wear this before you are blinded by the fogging on the lens created by the moisture from your breath?
How long would the filter last?
BATMAN!!!
Unused? I'm not sure if there really is much of a limit as long as its sealed in an air tight container. But if you do use it, you'll prob want to replace it after every use, just to be safe.
So if you had the means a 40 mm nato adapter could work if you found a way to set it up.
I love how you can buy a real gas mask that will actually protect you against stuff for the same price
Eh but it’s funnier to build it
Can we use regular charcoal crushed into a fine powder?
It wolud not be as effective
Around 100 Times less
Not a powder though
You should have added a 60mm to 40mm nato adapter to screw on some military filters
Isn't the MIRA Gas Mask nearly the same in shape with that Snorkel?
wouldn't it be easier to make the snorkel attachment into the filter and leave everything else intact ?
What if we have no snorkling mask....can you sir make a video of diy and around the house things like plastic bottles....we really need your help....FROM PHILIPPINES
In the filter deploy Active carbon?
Would this work against Corona virus ?
no
this would be useless for that, you need a real particulate filter for it
Him: I'll leave the links to the materials in the description
The Description:
5:33 looks like DEET bug repellent.... thats the good stuff. lol
I got my finnish gas mask... I think they are still fairly cheap too.
but I might would have flipped the "exhale" valve so you only get intake through the filter... then some sort of cobbled together valve for exhale gasses.
Thanks. I'll need this for the Coronavirus.
Eric Axton I hope it woks ...imma make one myself 👍👍👍 fucking virus is fucking up my summer 😒😒😒
Useless.
It can’t filter a virus. It ain’t a long chain of proteins like tear gas is. Just follow standard safety precautions.
I'll just buy one ...thankxxx anyway
IT'S FANTASTIC! THIS IS A PIECE OF HOT GLUE WITH A LITTLE MASK ON IT!!!
Military surplus MP5 gas masks are 30 bucks
if you’re talking about CHKadels or BUDK from the United states they list them as Polish MP5s but they’re actually a French ARFA. you can tell the difference easily because the french have holes in the voice diaphragm not the front and the Polish have circular lines
Double breathing the filter. No-no.
Should leave the exhaust valve intact and cut a new port for the filter.
i get the full face mask scuba and i get the half mask respirator and put the half gas mask in to the scuba mask does that work? sorry bad english
how well would it work against tear gas?
is it better than n95. XD
how to do upgrade to stop infection by CoVid19 Corona Virus?
dont build this, its useless for that
Just get a 3m p100 filter with a 3m half face respirator
Does This Filter Tear Gas?
Looks like a mashup between a WW2 mask and a modern one.
haha! Yeah it kinda does!
this is great, perfect for protesting in Thailand
My suggestion is that the activated charcoal sould have been crushed lightly, because the center of the pellet is useless oherwise and is wasted
overall great video
Does it work against nervegas?
-NoName- no the filters arent in the right specifications for it and you also would need an NBC suit
-NoName- no you would need a full NBC suit and not such a bad mask. Watch this for more information th-cam.com/video/HHsMWFZ7sM0/w-d-xo.html
where's the exhaust valve?
wouldnt it be easier to just use the air intake tube and mount the filter onto it? that way you could keep the exhale vale in the front of the mask
thank u for sharing the idea..luv this..just like that..yeah
Genius. Can you beat that Micgyver?
Lol I wanna see you test it against tear gas.
I saw your video because I am trying to make a mask for the corona virus. However I don't get your solution at all. You sealed the upper exhausts and breath in through the lower exaust. Where will the air go now? Back through the filter? This is not how gas masks, respirators or any masks work at all.
Great Show
🤝😎👍
I mean you can buy a GP5 gas mask for roughly £10 and then a new modern filter for £10 so you could buy a real mask with a working filter cheaper. Still a great video though.
It's even cheaper to substitute GP-5 with the Chinese TF-1. Still, it's still a good vid.
ZɪᴍUɴᴋɴᴏᴡɴ I don’t think the Chinese tf1 is cheaper because I’ve seen gp5s for sale between £5 and £15. The cheapest TF1 I’ve found costs £20
@@ItsSamHussey I forgot to mention that it's according to the location. Sorry for the misclassification. Here in Malaysia, TF-1 is the cheapest. Cheaper than a typical 3m respirator.
Thanks..i'm going to try and incorporate a hepa filter in there somehow
Can this be used against tear gas? Lol
maybe, probably not. You would need an actual particulate filter or military surplus filter for an actual gas mask
love your vid but i didnt use the can i used the 2 side half gas mask refillable filter only 6$ and glued the half gas mask into the full face mask snorkeling
cool beanz! :D
Smells like awesome!
hahaha! Thanks!
I've a school prjct which is i need to make something that can reduce air polution . Do y think i can make ths ? Ahahahaha im just afraid ppl can't breathe once they using ths . Please give me some opinion ?
That's really awsome
i paid 12€ for a soviet abc-mask including a filter. that thing will filter any fallout and tear gas
Estelon Agarwaen what is a soviet abc gas mask
Never heard of it did you mean GP5?
Not sure how the exhale would be without a valve system. Gas masks inhale through a filter and then exhale through a valve.
that air buble out part of mask perfectly fits for a gas mask but i have a another idea that part for fits too for carbon dioxide out part u put filter to under water air part and out carbon dioxide to out air part is a better idea i think btw sorry for bad english
That’s so cool!
You could have bought a real gas mask for the same price or maby cheeper and it would be more effective and there would be filters specifically for the mask instead of having to build one every time also it would just be more reliable
Where did you see a real gas mask for that price?
Stephanie Flores EBAY and a lot of surplus stores. I got two gas masks for about less than $60 a French ARFA and Polish MP4
@@stephanieflores5989 just look on ebay and you will find one for sure
YoMada thx
Anthony jaramillo thx
You can very well get a “military grade” gas mask for waaay less than a couple hundreds. Get ANY Chinese mask for example, plus like 10 to 20 dollars per regular Nato filters, BOOM perfectly working, new gas mask.
Mechanical Ninjineer I don’t unterstand, what you mean.
Lil Blyat On eBay you can buy surplus Soviet or Chinese gas masks for ~20$ or less
Russian RED Medic that too.
i got a tf-1 for 18 dollars!
Here because of coronavirus
Who else here in 2020
Awesome work, man! 😊
Thanks! :D
I’m just going to throw these two things out there, 1 ninjanear might have been able to smell the stuff he sprayed in the trash can because he may have not had a proper seal on the mask because of his beard. 2 military grade actually is worse than civil stuff, go civilian any time you can because it’s better.
Cyborg2101 that is the most retarded thing I have ever heard, nearly all civilian masks you can get that even come to close to even cold war military gas masks would be a fireman's air supplying respirator
_ISO_ are you military yourself??
Cyborg2101 no but I have experience with military gas masks and civilian ones. And I know a few people from the military and I know what gas mask they use. Civilian gas masks are a rip off 90% of the time because surplus military gas masks tend to be cheaper and higher quality than a civilian gas mask. And I garuntee that there is no civilian gas mask that you could show me that is better than a cheaper surplus military mask.(except maybe the isreali 4a1 but many people say it's uncomfortable)
_ISO_ well as one who is in the military I can promise the military ones are not as good as civilians think. Remember the government is buying them from the lowest bidder.
_ISO_ you can as a civilian get yours sized with a face mold and get it to your exact face as military we can’t we get to make so many times
Nice gas mask.
☺️👍
Thank you!
Wrong connector for shtf, you should put a pet bottle cap on the intake and use 600ml pet bottles, they are very easy to manufacture and have a lot more air travel and surface area in the lightest package possible.
AS a former service man who worked with NBC and similar in employment, great but, the one way valve should have been left and just tap a 40mm for your filters in case you run across reg. filters, place a secondary filter cover over said one way valve, after you spend hours in it or it fills with condensation sweat or clouds up in firefight, learn to make better than those $200+ models, and learn how to use these... technologies
I would like to make one, probably already made, complaint in that you shouldn't have painted the mount before gluing it in place, as that creates a point where it can fail very easily
this will help my anti-riot gear gear
Where's the description?
Great job