ฝัง
- เผยแพร่เมื่อ 7 ก.พ. 2025
- Below is where I got all the pieces for this zipline project.
Petzl Tandem Speed Pulley is available here: www.karstsports...
1" diameter x 18" long turnbuckle with jaws on each end (I actually used 3/4 x 24" but I said 18" in the video):
www.e-rigging....
Galvanized wire rope or steel cable here:
www.e-rigging....
Carabiners:
www.karstsport...
How to choose a climbing harness:
• Buying a Climbing Harn...
www.rei.com/le...
Good one! there are new units available in market for braking, I suppose this zipline was made 4 years ago and those units were not available readily then. Just for the safety reasons, you can upgrade it with the good braking units and get rid of the frictional brakes.
Looks totally fun! I'm also looking into possibly building a short one, not too high off of the ground to c how i like it but high enough to clear a vehicle parked in the front yard. I'm gonna buy the trolley first & then the rest as i go along.
So jealous lol... I just put up a 40 foot zipline in our backyard for the kiddos, that's all that would fit in this suburban neighborhood house. Hopefully one day when I'm a grandpa I'll have some land to do this for my grand-kids. I learned something from you that I am going to use. I bought the Slacker's zipline kit and it did not come with a U-Buckle or cable tension-er. Instructions literally tell you to grab a couple people and for them to hold the cable up with a broom while you pull on the other end and secure the U clamps. I'm gonna rig one of the ends up to do that... Thanks for the video bud, nice looking family you got there.
@ Nate "...Hopefully one day when I'm a grandpa...."
Well, one grandpa to another 110' is all I have to work with :-(
It all depends on how long your zipline is going to be and how fast you want to go. This line only drops 9 ft over a 180 ft long run, which is a pretty mild slope. If your line is only half that long, then you'd only need about a 5 ft drop in height, which you can get from a flat yard by just building a small platform at the start.
Is a platform a necessity?
Whare do u get it
Thanks! My kid has been asking for this for years
Thank you for protecting the tree. 🌲😘🌲
Great Video.. gonna build one on our land and use your design!
How do you adjust the turnbuckle while attached to the line without having the line turn and tangle at the same time?
That looks mad
theres a u bar pointed at you on the landing port. isn't it dangerous??
Nice, but 170 feet ends fast. I have a 300 feet back yard, perhaps more line equals more fun
I know this is old video, but if you're still there I'd love to know how you bring that trolley back up.
There are two lines, so we unhook the trolley (Petzl Tandem Speed Pulley) after every ride and carry it with us to the other line. If you use quick-release carabiners, they open and close very easily and you learn the thumb movement to open/close them in just a few tries, so unhooking and re-hooking is easy, even for kids.
Enjoyed your video. We are gathering our supplies to make one in our backyard. One question, how do you get it back to starting position? Is there a long rope you walk up the hill with?
We have two ziplines: One goes across the small ravine, then you unclip the harness, walk up the hill about 15 feet, attach the harness to the second zip line, and come back across the ravine.
How do you take the harness back up to the top?
There is one line that goes out, and another line that comes back to the start.
Matthew , since you have experience in the zip line experience, i would like to you about a little project i have rogh now , any eamil adrres you could provide me?
I want to build zipline to but what is the price of all those things?
Me and my cousin are making one
That's really cool
How do you get the zip line back up the hill?
We have two lines, 1dt line goes out, 2nd line comes back. The 2nd line ends at a spot lower on the slope than the 1st line, so you have to walk uphill a little bit to get back to 1st line.
Do turnbuckles break under pull? Think redundant systems,
These turnbuckles are very stout, they weigh about 15 pounds each. if you saw their construction and the depth/type of threads on them, you wouldn't worry. If this was a commercial operation with daily use by 250-300 pound average obese customers, I'd go with a redundant setup. but this is just for occasional family use.
I have seen all sizes break under load, they are cast, not a bar of steel. It may well last a long time. But, if it breaks under load, someone will be seriously injured. Also, you should consider cable weight, because this weight is in addition to your rider. Using another length of cable (with eyes ) in parallel to the turn buckle (same length) provides a backup plan and may reduce system pull.
Doc Dichenberm If you've seen ALL sizes break under load, then you have a very weird job. The way I see it, if you're building or riding a zipline, you should do all you REASONABLY can to reduce risk, but there is a limit, and a certain amount of risk has to be accepted. I'm willing to accept that something rated to hold multiple thousands of pounds will hold me and my few hundred pound passengers. Sure, a turnbuckle might break, and I might get hit by lightning or board the wrong plane and crash. The amount of risk with these turnbuckles is about the same as those possibilities.
I work as a stage rigger, we use a ten to one ratio of system strength to load. Under normal circumstances a system may be fine but,introduce winds or rain (materials absorb water) and the system buckles under load. Having a safety on the rig is just good sense
Doc Dichenberm I work building commercial zip lines, turnbuckles are considered to not be ok due to as you said the lack of redundancy. Usually a bolt is drilled through a tree or pole (or tree wrap) and is backed up with a copper swaged choker.
how much did it all cost
So cooll
Wow loads of help
that's like girding a tree ... it will kill the tree, which will make the tree dangerous. ( see previous comment )
i tried it AWESOME
We're building one
How do you get the pully back to the top?
We have two ziplines. One takes you out and the other brings you back. When you get to the end of the first line, you have to unclip from the Petzl Tandem pulley and move it to the second line, then ride it back to the start. We considered attaching a short rope to the pulley to walk it back by hand, but that seemed like no fun, so we built the second line so you can ride back.
@@mcwhitet Excellent ideal... My grand kids would love it!
Looks like my back yard
I wunt to get a zip line. But my yard is small
I'm getting one it is 25 m
meters?
very nice
Do it with your lovely dog, it seems like he wants it :D
W vid
how thick of cable did you use?
This is 3/8" galvanized cable, or some people call it wire rope.
Mad
cosby clamps on wrong dont saddle a dead horse
Nice
good video....also check out the video called Zipping With Billy
Around how fast do you go with a 180 to 9 setup
Probably about 15 mph. It depends on how much tension you put in the line with the turnbuckles. My line is pretty tight, so a slacker line will be a little slower.
Ross S okay thank you
Wire Rope Clamps are installed in the wrong side !!!
No they're not, I checked them three times during construction and had them checked by a friend who does this for a living.
The wire rope clamps ARE installed correctly. "Never Saddle a Dead Horse", which means the larger metal saddle goes onto the LIVE side, which is the working side of the cable, and the smaller bolt portion goes on the "dead" side, which is the cable end as it returns to the live side. These clamps are installed correctly.
He installed them correctly. The Crosby clamp 'saddle' refers to the wire clamp plate. not the u-clamp... I'm not one to correct people online. but if you put the u-clamp on the live side of the bite and tension to the correct torque you will damage the cable and potentially kill someone. Please don't do that. If in doubt with any rigging operations seek professional help.
@@davidcahill2154 Look carefully, some of these clamps are correct but others are not. Note the cable around the tree at the beginning, it is NOT correct. The rule is as stated above "never saddle a dead horse" meaning the wide "saddle" part of the clamp should not be on the short "dead" end but on the main line portion holding the load. This does protect the main cable from potential damage and failure at less than the full rated load.
@@dness8 Are you watching a different Video?
You can clearly see the short end on top at the end you are talking about (see 2.02 seconds and 0.44). and the saddle (cable clamp) is fitted to the bottom with the U-clamp on the top attached to the short end. The assembly is place upside down from the way it is presented at the start (0.13). Which is probably throwing you off.
My only criticism of the system is that there is in-adequate spacing on the in the bottom end of the main line where it connects to the tree sling.