I tried out, but for me it does not work ? Do you need a certain tension on the thread or maybe a special thickness on the thread ? Please help me ? I tried Big capital letter “F” (Patterns II and code 16) and it almost broke my needle and stopped. Then I tried Patterns I : code 93, 96, and 97 it worked but it does not look exactly as the picture and it is not beautiful and the form is not constant ??
Hello again, After tested several thing. I found that the following worked for me : Using a thinner thread, and a sort of paper support that I ironed on the soft tissue (if the tissue is to soft), and the « A » foot, and I took (this time) a lot of care (when threading the upper thread) to guide the thread around the thread guide pulling the thread through the pre-tension spring. This is very important ! Attention that the thread go down in the gap between the two blade, which is the pre-tension spring. Before I did not put it correctly. And also, I noticed, the tension of the thread is important when winding the bobbin. I hold it slightly between my fingers and used I higher speed (between middle and low). And I checked carefully that there are a certain tension in the thread when pulling it. Both for the upper and lower thread. And also, for the lower thread, when inserting the bobbin, I noticed, another thing that is important, that is to make sure to hold gently with one finger on top of the bobbin when you draw the thread, following the arrow markings into the stitch plate thread guide from A to B and finally to C. (See Manual, page 9, to be found on internet, see internet site below). Then I tried different tension from zero to 7, and found out that, for me, tension 5 was the best option when sewing letters. And, finally it worked, I succeeded to write my name perfectly. I never thought that you had to be so precautious about the threading, the tension of the thread, the tissue support, and the type of foot. (The manual can be found here: www.bernette.com/en/models/bernette-sew-go-8, Or more precisely here : www.bernette.com/assets/uploads/general/Downloads/User-Manual/Sew-Go/EN/5029008.0.04-IM_sewgo-8H20HEN230630.pdf) //Fredrik
@@LittleEllysElizabeth madam how is this machine works?? Is it working good i m beginner i wanted to purchase this model pls give me the review about this model thank you
@@LittleEllysElizabeth I did it! 😃… used interfacing and better thread. And with the standard foot I used the embroidery collection and also the alphabets. And it worked.
@@amreennawazkhan7445 so far it is good. But I am seeing some issues with timing with zigzag because I need to service it . It has been more than 2 years since I purchased it.
I tried out, but for me it does not work ? Do you need a certain tension on the thread or maybe a special thickness on the thread ? Please help me ?
I tried Big capital letter “F” (Patterns II and code 16) and it almost broke my needle and stopped.
Then I tried Patterns I : code 93, 96, and 97 it worked but it does not look exactly as the picture and it is not beautiful and the form is not constant ??
Let me give a try and get back to you
Hello again,
After tested several thing. I found that the following worked for me : Using a thinner thread, and a sort of paper support that I ironed on the soft tissue (if the tissue is to soft), and the « A » foot, and I took (this time) a lot of care (when threading the upper thread) to guide the thread around the thread guide pulling the thread through the pre-tension spring. This is very important ! Attention that the thread go down in the gap between the two blade, which is the pre-tension spring. Before I did not put it correctly. And also, I noticed, the tension of the thread is important when winding the bobbin. I hold it slightly between my fingers and used I higher speed (between middle and low). And I checked carefully that there are a certain tension in the thread when pulling it. Both for the upper and lower thread. And also, for the lower thread, when inserting the bobbin, I noticed, another thing that is important, that is to make sure to hold gently with one finger on top of the bobbin when you draw the thread, following the arrow markings into the stitch plate thread guide from A to B and finally to C. (See Manual, page 9, to be found on internet, see internet site below). Then I tried different tension from zero to 7, and found out that, for me, tension 5 was the best option when sewing letters.
And, finally it worked, I succeeded to write my name perfectly. I never thought that you had to be so precautious about the threading, the tension of the thread, the tissue support, and the type of foot.
(The manual can be found here: www.bernette.com/en/models/bernette-sew-go-8,
Or more precisely here : www.bernette.com/assets/uploads/general/Downloads/User-Manual/Sew-Go/EN/5029008.0.04-IM_sewgo-8H20HEN230630.pdf)
//Fredrik
@@hansfredrikjohansson8742 Thank you. Have pinned your comment so that others can find it easily
Thanks for pour explications 🙏😉
Happy to help
Mam ,why the machine sew by it self after I stop stitching,what is the problem with my machine
How long has it been since last service? Is the problem when you use foot pedal or start/stop button?
Which Thread and interface have you used? do put in links if its available online.
I have used normal madhura coats thread and common paper interface
Mam current shock problem solved in your machine ?
Have not experienced it in the past one year.
@@LittleEllysElizabeth madam how is this machine works?? Is it working good i m beginner i wanted to purchase this model pls give me the review about this model thank you
Which foot did you use to sew the alphabets? I tried with the standard foot that came attached with the Bernette sew & go 8, and it didn’t work.
Standard foot only. Can you watch my video again and try once more? Also use stabilizer or interfacing.
@@LittleEllysElizabeth Thank you for your reply. I’ll definitely try again. I am an absolute beginner
@@LittleEllysElizabeth I did it! 😃… used interfacing and better thread. And with the standard foot I used the embroidery collection and also the alphabets. And it worked.
@@Shamazcorner Great. Happy for you.
Mam round beads foot use hota h kya isme
they don't include it in the machine. You have to buy seperately. alag se gharidana padega aapko
@@LittleEllysElizabeth thank you so much ma'am.aaoki machine work properly.any problem in this machine
@@amreennawazkhan7445 so far it is good. But I am seeing some issues with timing with zigzag because I need to service it . It has been more than 2 years since I purchased it.
@@LittleEllysElizabeth thank you so much.which machine is better
@@amreennawazkhan7445 compared to which machine?
En français
You can use auto.translate to french