Dude ...Had a leaky valve. Watched several videos showing me how to replace the whole shemozzle. Found your video...solved my problem in 15 minutes and for $5. You are a Rock Star!!!
Same here. I did not know such part existed. I could not remove the compression ring and was about to give up and call a plumber. You saved me time, money, and sanity. Thank you Carlos!
Thanks so much for making this! Super underrated video lol. Everyone’s replacing the entire valve. Not much out there to replace the knob fixture. Thank you!
Thank you so much! I'm a 64 year old female and was worried I'd have to call a plumber, but watched your video and just got through replacing my stem valve by myself. You are a life saver. ❤
Great video! I had both hot and cold shut off valves that were 28 years old. When I turned the water off, both valves would still trickle. I wasn't sure what to do, what to buy, or anything, to fix them. I watched this video, went to the hardware store, bought the exact hardware shown in this video, and did it. Everything went well, except for one thing (and it was unrelated to this video). After I completed the work, I went to turn the water back on at the street so I could test my handiwork. But somehow, the bidet had gotten turned on while the water was shut off to the house. My wife was watching the valves for me when I turned the water on, and almost got sprayed by the bidet water! Lol But the stem valves I had replaced both worked beautifully. Now I just have to convince my wife that the bidet thing was a compete accident. 🤣
Excellent Video....Any time you are going to replace the supply line to a sink or toilet, you should have a stem repair kit or new stop on hand. A stop that has never leaked before may very well start leaking because old brittle seals were trashed merely by closing and opening the stop one time to make a repair. I like the new seals versus new stop.
THANK YOU for getting STRAIGHT DOWN TO IT. I just fixed the faucet cartridge on my faucet because it was dripping even in the off position, then when i went to turn the hot water valve back on it started leaking too! I just wanted to see how to remove the stem because mine seems stuck! You gave clear, quick instructions and showed what you were doing up close THANK YOU! YOU ARE AWESOME!
1:14 yeah I see the difference. The old one was made of metal. When I do mine, I’ll check if I can keep that and change the rubber only. Thanks for showing this method!
As long as it's a brass craft valve , I buy the repair kit at home depot it takes no time to change . Been doing it that forever . There's nothing wrong with the body of the valve. No need to mess with the compression fitting
Fantastic video! This country needs to get over its addiction to just throw away and replace stuff. No more cheap stuff from China. So be prepared to watch more such videos and fix/repair your broken equipment.
It will be painful but is necessary to reduce Chinese made products and start making more products in the U.S.A. again. In the long run the U.S. itself will be stronger and there will be more jobs available back in the U.S. again
Or you could just replace it with another BrassCraft. Made in USA. There not made as well as the older one. Hence the plastics. I might have replaced the screw, washer and bushing. I just did that recently. Should last another 15 yrs until I need to touch it again.
THANK YOU!!! every other video instruction replaced the entire set up, this is exactly what I needed. I just called a plumber to come out. You saved me a house call fee and only God knows how much to replace a $3 part.
Thank you for this! I spent hours trying to remove the actual entire shut off valve from my mothers old 1950s pipes that were rusted and impossible to take off and just realized I could have just replace the stem thanks to you!
You have to heat these old shut off valves with a flame to remove them completely, if you don't they will probably brake when you try to turn them to remove them.
I found your channel today, and have to subscribe, because your videos go straight to the point, and explanations are clear and concise. Thanks so much for sharing your knowledge!
I liked your video very much, but I have a few things to add. You should say that the stem "screws" out. I was pulling on it for a little while before I realized this. Also, remind people to remove the old washer from the retention nut. Some people might not notice this or try to reuse the old one. Lastly, my old handle from 1986 did not fit the new stem. Tell people they might want to save themselves a trip back to the hardware store by spending a little more by buying a new handle too.
Very helpful for a quick repair for an old corroded pipe thread valve that is too close to the wall to easily remove the old valve body. Ace or a good plumbers supply may have the kit. Big box stores typically don’t stock repair kits, usually new valves only.
Great video! I've got a shut off valve under the kitchen sink that is leaking just a little. I didn't know they made repair kits for those valves. Thanks for posting this! BTW, any idea how durable the new plastic parts are?
This was very easy to follow and it all went well. But tank still fills very slowly, so I think I need a new float valve. And I learned something and built a little confidence.
Great to hear that the tutorial was easy to follow and things went well!. It's awesome that you learned something and gained confidence through the process. Keep up the good work! 🚽🔧👏
I was very excited to see this video, since I didn't know what I needed until I saw it. I just ran to the store and grabbed the replacement part. I just discovered that the washer at the end of the original stem had broken off inside the valve, so that was fun getting that out. Only to find that the threads on the replacement stem don't match my hardware. Old valve, maybe when there was a different standard in the 60's? Is there even a standard? I really hate plumbing. I did manage to get the old stem back in with no leaks with the valve open, so at least I'm happy about that. Need a plan B in getting new faucet and supply lines installed. Hmmm
Even cheaper, just replace the rubber washer. While you are at it, also replace the rubber washer in the outdoor faucets as well. For the indoor faucets, I just replaced the entire valve with compression fit quarter turn valve. The quarter turn valves will last a long time as they do not have the rubber washer that wears out over time. The down side in older houses is that the plumbers soldered the valves onto the pipe which requires you to saw them off with a hacksaw or if you have enough room remove the old valve with a pipe cutter.
I only find the multi turn valve at Home Depot. My valve is quarter turn. Still trying to figure out if I can just replace the stem or do I have to replace the whole valve. Your vidoe gave me hope initially but I cannot find a quarter turn replacement valve stem. Not even online.
Excellent to use repair kit..the other option is to replace with the 00 washer for the shut off valve. Best to reduce unnecessary wastage with needless landfills also time and money's
Great point. I do have in mind making a video in the future showings all options and pros and cons for each, like cost and waste... Thanks for watching!!!👍😀
@suekotchevar2765 yes they do sell in big box stores like menards and home depot. However you have to warm up the 00 washer because then you can force it in. It will work since I used it. You should reuse the old metal stem if it is not a plastic stem. New stems are all plastic.
Does this work on ones where the knob sticks out the side like a T? Appears to be a straight through compression valve with the clear brassworks knob/handle on the side. The piece right behind the handle appears to unscrew.
Can you rebuild a quarter turn valve?Do you have a preference towards multi turn valves if they are the only ones you can rebuild.Also I had an extra multi turn valve & opened it up & the stem is metal or brass?Anyway would it be wise to purchase a new valve & just use the new stem instead of replacing it with a plastic one?
Absolutely, you're right! Quarter turn valves generally can't be rebuilt due to their unique design. When it comes to replacing multi-turn or quarter-turn valves, I prefer quarter-turn valves for their reliability and ease of use. While I showed a possible repair in the video, if you have the tools and time, a complete replacement with a new quarter-turn valve is often the better choice for long-term reliability. Thanks for tuning in and asking these questions! 👍😊
You're very welcome! I'm thrilled to hear that the video helped save your day. If you have any more questions or want to share your experiences, feel free to do so. Happy to help! 😄🔧👍
I want to do this fix on my valves, but I'm worried something might go wrong and I'll be forced to leave the main water line shut off and I won't be able to use water in the house. Is there any chance something might go wrong by doing this fix? What would you rate the success rate of doing this repair?
If my toilet is periodically running on its own, could the issue be the shut off valve? I tried replacing the flapper but when i went to turn the water off, no matter which way i turned or how far the water shut off valve would not shut the water off. Could that be the issue or would it be the water fill gauge that sits in the toilet bowl itself?
Is there any benefit to keeping the older, metal shut off valve and just stealing/replacing the new rubber washers? (Wondering about the longevity of the new plastic valves versus the older metal valves)? Thanks!
Metal “guts” are definitely more robust. They do sell them but it’s harder to find. This is just another item in our home that forever it will need maintenance.
Probably just a new washer would seal it up also. But you just happened to find a repair kit from the same manufacturer, which is not necessarily an easy thing to find in many cases.
The first part of this video looks identical to my situation but at 53 seconds after unscrewing the handle and removing the retention nut I discover a smooth metal dome securing the old valve stem in place. Do you know what that is? Is it removable by DIY?
Don’t be worried. It’s pretty simple. I recommend open a faucet somewhere in the house, then try shutting the water off, you should hear the water stop running, you then know it’s off. Good luck.
Looks like this stem can only be replaced if it is a muti turn handle. If you have a quarter turn valve it looks like you do have to replace the whole thing. This video gave me hope for a simple fix but now my stress level is building.
so why would you replace it with a "cheaper" setup? Why not just replace both the washers? Mine shuts the water off fine, but it leaks a little from the stem. So it has to be the rubber gasket on the outside part. I have not done any changes for like 20 plus years and when I needed to service the fixture and need to shut off the water, this issue came up.
Can i buy just the rentention nut? Mine is rounded out, slightly leaking and the little screw that holds the valve handle cant be unscrewed with a screwdriver because someone mangled it.
You might consider a second wrench on the valve body to keep it from rotating/leaking when loosening the nut.
For sure! Great tip!
Dude ...Had a leaky valve. Watched several videos showing me how to replace the whole shemozzle. Found your video...solved my problem in 15 minutes and for $5. You are a Rock Star!!!
Wow!! good stuff ... thanks!
Same here. 100% on point
Same here. I did not know such part existed. I could not remove the compression ring and was about to give up and call a plumber. You saved me time, money, and sanity. Thank you Carlos!
Thanks so much for making this! Super underrated video lol.
Everyone’s replacing the entire valve. Not much out there to replace the knob fixture. Thank you!
Dude, same. Just finished, and can confirm 5 bucks and 15 minutes. And no anxiety meds needed.
This saved my day! I couldn’t get the valve off and this is way easier to replace than the whole thing. Thank you!
Wow… I’m glad this worked for you… yes! Sometimes we just need few parts to repair and don’t need to replace anything.
Thank you so much! I'm a 64 year old female and was worried I'd have to call a plumber, but watched your video and just got through replacing my stem valve by myself. You are a life saver. ❤
Fantastic!
Ss long as pipe isn't rusted.
Great video! I had both hot and cold shut off valves that were 28 years old. When I turned the water off, both valves would still trickle. I wasn't sure what to do, what to buy, or anything, to fix them. I watched this video, went to the hardware store, bought the exact hardware shown in this video, and did it.
Everything went well, except for one thing (and it was unrelated to this video). After I completed the work, I went to turn the water back on at the street so I could test my handiwork. But somehow, the bidet had gotten turned on while the water was shut off to the house. My wife was watching the valves for me when I turned the water on, and almost got sprayed by the bidet water! Lol
But the stem valves I had replaced both worked beautifully. Now I just have to convince my wife that the bidet thing was a compete accident. 🤣
Sounds like a Laurel & Hardy episode😅
Excellent Video....Any time you are going to replace the supply line to a sink or toilet, you should have a stem repair kit or new stop on hand. A stop that has never leaked before may very well start leaking because old brittle seals were trashed merely by closing and opening the stop one time to make a repair. I like the new seals versus new stop.
Exactly, it’s one of those things, once you touch it many things can go wrong. Great idea! 💡
THANK YOU for getting STRAIGHT DOWN TO IT. I just fixed the faucet cartridge on my faucet because it was dripping even in the off position, then when i went to turn the hot water valve back on it started leaking too! I just wanted to see how to remove the stem because mine seems stuck! You gave clear, quick instructions and showed what you were doing up close THANK YOU! YOU ARE AWESOME!
Thank you so much for the comment.
Thank you for this video! First time homeowner here and you just saved me some tears and a call to the plumber
Great to hear!
1:14 yeah I see the difference. The old one was made of metal. When I do mine, I’ll check if I can keep that and change the rubber only. Thanks for showing this method!
That part honestly doesn't really matter since it's always the gasket part that goes first
As long as it's a brass craft valve , I buy the repair kit at home depot it takes no time to change . Been doing it that forever . There's nothing wrong with the body of the valve. No need to mess with the compression fitting
OMG. Because of your video, I Saved $600! New valves not needed, new faucet not needed. 🎉🎉🎉🎉
Fantastic video! This country needs to get over its addiction to just throw away and replace stuff. No more cheap stuff from China. So be prepared to watch more such videos and fix/repair your broken equipment.
It will be painful but is necessary to reduce Chinese made products and start making more products in the U.S.A. again. In the long run the U.S. itself will be stronger and there will be more jobs available back in the U.S. again
Or you could just replace it with another BrassCraft. Made in USA. There not made as well as the older one. Hence the plastics. I might have replaced the screw, washer and bushing. I just did that recently. Should last another 15 yrs until I need to touch it again.
THANK YOU!!! every other video instruction replaced the entire set up, this is exactly what I needed. I just called a plumber to come out. You saved me a house call fee and only God knows how much to replace a $3 part.
Glad it helped!
Thank you for this! I spent hours trying to remove the actual entire shut off valve from my mothers old 1950s pipes that were rusted and impossible to take off and just realized I could have just replace the stem thanks to you!
You have to heat these old shut off valves with a flame to remove them completely, if you don't they will probably brake when you try to turn them to remove them.
This was a very helpful video. You made an easy job of what started out as a difficult problem. Thank you!
My hero! Every other video made it complicated and you made it so easy for me! Thank you!
Glad it helped!
Great video! Clearly explained the step-by-step process. You save me a lot of money and time. Thanks.
Thanks, I was worried about removing entire valve and busting it from pipe, this is much easier, less risk!
Awesome!! 👏
You are fantastic, your video was so easy to understand . I fixed my problem in 15 minutes, thanks to you . Keep up the good work.
Nice!! way to go....
Hi! My shed guy also does plumbing...that's great! You always make it easy to follow along.
Best video I have seen on this topic. Perfect explanation.
I'm thrilled to hear that you found the video helpful! Thanks for watching and supporting the channel! 🛠️👍😊
This is great. Have a bathroom valve and a dishwasher valve that need work, so this was perfectly timely.
This was super helpful to us today! Thanks so much for the concise, well-explained tutorial
I found your channel today, and have to subscribe, because your videos go straight to the point, and explanations are clear and concise.
Thanks so much for sharing your knowledge!
Appreciate the feedback… it’s viewers like yourself that makes creating content fun and enjoyable…. Thanks for watching!!!
I know how to do this but I want to make sure I am doing it right. Happy to find your video! Thanks!
You can do it!
This video is perfect. I was able to do the replacement easily. The steps shown here are exactly what's needed and are easy to understand. Thank you!
You're welcome!
I liked your video very much, but I have a few things to add. You should say that the stem "screws" out. I was pulling on it for a little while before I realized this. Also, remind people to remove the old washer from the retention nut. Some people might not notice this or try to reuse the old one. Lastly, my old handle from 1986 did not fit the new stem. Tell people they might want to save themselves a trip back to the hardware store by spending a little more by buying a new handle too.
Oh! Thank you so much for the feedback… I’m sure I’ll do more of these and for sure will hit those points… thanks again!!!
THANK YOU!!! This is the video I was looking for. My leak is at the the shut off knob. Been looking for this option. Awesome video!
Outstanding pics, pace of instruction, angles. Thank you sir 😊
Excellent no nonsense video! Thank you.
I found this video just in time. A simple solution that I can do 👍.
Thanks for taking time to make this. No plumber needed🎉
You bet!
Thank you so much for your help! I feel so empowered to be able to repair it myself and save a ton of money. You are a blessing!
Glad to help
Thank you! I’m a master in the lawn, but plumbing, that’s a whole other level :)
Hahaha. Well we learn something everyday. Thanks for watching.
Very helpful for a quick repair for an old corroded pipe thread valve that is too close to the wall to easily remove the old valve body. Ace or a good plumbers supply may have the kit. Big box stores typically don’t stock repair kits, usually new valves only.
Yes, I see this less and less in the big box stores.
Great video! I've got a shut off valve under the kitchen sink that is leaking just a little. I didn't know they made repair kits for those valves. Thanks for posting this! BTW, any idea how durable the new plastic parts are?
Thank you so so much your video explained everything excellent. I was able to fix the bathroom shut off valve. ❤
Good job, my friend.
You gave me another weapon in my arsenal to make money 💰 🤑 💸
Got get them!!! Thanks for watching
After you put in the stem, is it in the open or closed position?
😄Great explanation. Clear instructions and easy to follow. Thank you.
Glad it was helpful!
THANK You for posting this!!!
This was very easy to follow and it all went well. But tank still fills very slowly, so I think I need a new float valve. And I learned something and built a little confidence.
Great to hear that the tutorial was easy to follow and things went well!. It's awesome that you learned something and gained confidence through the process. Keep up the good work! 🚽🔧👏
Great demonstration. Thanks!
You're welcome! I'm glad you found the demonstration helpful. 😊🔧
Really nice job man! I learned something new
Hey buddy! Thanks for watching… Your channel is kicking ass! Good stuff!
You are a blessing, bro! I just fixed my valve due to your video easy!
Awesome man!! Thanks for the comment.
Very helpful and easy to follow. Thank you so much.
Stem broke easily when I tried to shut off water supply to take. Thanks for instructions on how to replace it.
Cool!! I'm glad it helped.
Basic question:
Are all shut off valves syandard size?
Mine is an upscale mobile home.
What about the washer at the back of the valve that connects to the water supply? What is that washer is deteriorated too?
Does it matter if we have a quarter -turn shut off valve? Does it still have similar inside parts?
Probably need to replace the whole value eventually, but this is a great quick fix.
yup. that my problem. I didn't put the plastic with the rubber onto the nut. thank you.
OMG! Thank you! You made this so easy to follow!
I was very excited to see this video, since I didn't know what I needed until I saw it. I just ran to the store and grabbed the replacement part. I just discovered that the washer at the end of the original stem had broken off inside the valve, so that was fun getting that out. Only to find that the threads on the replacement stem don't match my hardware. Old valve, maybe when there was a different standard in the 60's? Is there even a standard? I really hate plumbing. I did manage to get the old stem back in with no leaks with the valve open, so at least I'm happy about that. Need a plan B in getting new faucet and supply lines installed. Hmmm
Hey! Thanks for watching…. I have a video on my channel on how to replace this, it’s really easy and diy friendly. Good luck
Saved me money and time. Perfect!!🎉 Thank you!
So glad!
Thanks did not know i could only change this part not the whole thing
Even cheaper, just replace the rubber washer. While you are at it, also replace the rubber washer in the outdoor faucets as well. For the indoor faucets, I just replaced the entire valve with compression fit quarter turn valve. The quarter turn valves will last a long time as they do not have the rubber washer that wears out over time. The down side in older houses is that the plumbers soldered the valves onto the pipe which requires you to saw them off with a hacksaw or if you have enough room remove the old valve with a pipe cutter.
I only find the multi turn valve at Home Depot. My valve is quarter turn. Still trying to figure out if I can just replace the stem or do I have to replace the whole valve. Your vidoe gave me hope initially but I cannot find a quarter turn replacement valve stem. Not even online.
Does this only work if you have the same kit for the brand in question?
Excellent to use repair kit..the other option is to replace with the 00 washer for the shut off valve. Best to reduce unnecessary wastage with needless landfills also time and money's
Great point. I do have in mind making a video in the future showings all options and pros and cons for each, like cost and waste... Thanks for watching!!!👍😀
Does the super stores carry 00 washers best way to go
@suekotchevar2765 yes they do sell in big box stores like menards and home depot. However you have to warm up the 00 washer because then you can force it in. It will work since I used it. You should reuse the old metal stem if it is not a plastic stem. New stems are all plastic.
@@alekmartin9999 thanks
Great tip just what I needed
awesome explanation, I"m going to order some stem repair kits today!
Good luck!
Thanks! For the video! It really helped 😊👍
exactly what i was looking for thanks
Does this work on ones where the knob sticks out the side like a T? Appears to be a straight through compression valve with the clear brassworks knob/handle on the side. The piece right behind the handle appears to unscrew.
This helped out so much. Thank you
Wow ! You are the man
Exactly what I need to see .
Thanks for sharing
Liked & Shared
Glad it was helpful!
Can you rebuild a quarter turn valve?Do you have a preference towards multi turn valves if they are the only ones you can rebuild.Also I had an extra multi turn valve & opened it up & the stem is metal or brass?Anyway would it be wise to purchase a new valve & just use the new stem instead of replacing it with a plastic one?
Absolutely, you're right! Quarter turn valves generally can't be rebuilt due to their unique design. When it comes to replacing multi-turn or quarter-turn valves, I prefer quarter-turn valves for their reliability and ease of use. While I showed a possible repair in the video, if you have the tools and time, a complete replacement with a new quarter-turn valve is often the better choice for long-term reliability. Thanks for tuning in and asking these questions! 👍😊
so just to confirm,use quarter turn valves when possible?
@@Dave-ld3dr Yes, 100% !!!!
@@DIYPlumbingGuyThanks!
Is that true that you can also just replace the washer
Super helpful! Thanks. Is the replacement stem repair kit universal or is it specifically for BrassCraft?
Yes they are.
If the valve handle broke off can I just replace it?
Thanks for saving my day!
You're very welcome! I'm thrilled to hear that the video helped save your day. If you have any more questions or want to share your experiences, feel free to do so. Happy to help! 😄🔧👍
I want to do this fix on my valves, but I'm worried something might go wrong and I'll be forced to leave the main water line shut off and I won't be able to use water in the house. Is there any chance something might go wrong by doing this fix? What would you rate the success rate of doing this repair?
If my toilet is periodically running on its own, could the issue be the shut off valve? I tried replacing the flapper but when i went to turn the water off, no matter which way i turned or how far the water shut off valve would not shut the water off. Could that be the issue or would it be the water fill gauge that sits in the toilet bowl itself?
I did exactly by the steps but now I get a slow dribble, not water. Any suggestions?
Thanks. Have ready a couple of small containers rather than rags, just in case ....
Yes! Just in case 😊… never know
Wonderful video! Thank you!
Thank for the easy tutorial-very helpful
You're welcome! Glad you found the tutorial helpful! 😊🛠️
Good video. You made it easy to do.
Thank you for the great video 👍
Glad you enjoyed it
The repair a plastic stem whereas before it looks like brass, see 1:14. Cant that plastic break easily?
Is there any benefit to keeping the older, metal shut off valve and just stealing/replacing the new rubber washers? (Wondering about the longevity of the new plastic valves versus the older metal valves)? Thanks!
Metal “guts” are definitely more robust. They do sell them but it’s harder to find. This is just another item in our home that forever it will need maintenance.
Probably just a new washer would seal it up also. But you just happened to find a repair kit from the same manufacturer, which is not necessarily an easy thing to find in many cases.
Perfect and I am normally NOT a handyman.
Great! I love when it works out…
My valves don’t leak, but they are frozen. Would this fix the problem?
thanks.. good advice... ( my valve is soldered in, so the guts need replacing before un-soldering the old valve... again, thanks...
So this will fix a stuck shut off valve?
Great job....Thank you!
Thank you..have a blessed day
You too. Thanks for watching.
Help ive stripped the stem grip and it won't budge ive tried wd40 and everything how do I get it out
The first part of this video looks identical to my situation but at 53 seconds after unscrewing the handle and removing the retention nut I discover a smooth metal dome securing the old valve stem in place. Do you know what that is? Is it removable by DIY?
Wait… is it’s multi turn valve like the one in the video or a quarter turn valve? A quarter turn valve is not serviceable, it needs to be replaced.
I’m scared to shut off main water . Will I be ok ? And what should I do when shutting off
Don’t be worried. It’s pretty simple. I recommend open a faucet somewhere in the house, then try shutting the water off, you should hear the water stop running, you then know it’s off. Good luck.
Looks like this stem can only be replaced if it is a muti turn handle. If you have a quarter turn valve it looks like you do have to replace the whole thing. This video gave me hope for a simple fix but now my stress level is building.
nice video i always replace the entire valve good to know
Good video easy explanation for the dy guy to get
The universal kits don't fit mine, figures. the screw pattern on the plastic one is more narrow than the stem screw pattern I am replacing. Cheers!
If you got the whole shut off valve assembly can I just get the gut from new one and put on the existing old one?
Yes, if it’s a multi turn valve you can. I’ve done it before.
Thanks@@DIYPlumbingGuy
so why would you replace it with a "cheaper" setup? Why not just replace both the washers? Mine shuts the water off fine, but it leaks a little from the stem. So it has to be the rubber gasket on the outside part. I have not done any changes for like 20 plus years and when I needed to service the fixture and need to shut off the water, this issue came up.
Thank you, brother, you are the best!!!
Oh man!! I’m glad it helped.
Can i buy just the rentention nut?
Mine is rounded out, slightly leaking and the little screw that holds the valve handle cant be unscrewed with a screwdriver because someone mangled it.
I have not see just the retention nut. Maybe at this point is best to buy a replacement unit, pull out the retention nut and use here. Good luck!