Toyota Turn Signals Not Working - Diagnosis and Repair
ฝัง
- เผยแพร่เมื่อ 5 ก.ย. 2024
- Toyota Turn Signals Not Working - Diagnosis and Repair. Was it my fault? In this video I show how I diagnose and fix the turn signals not working on a Toyota Sienna. The blinkers and hazard lights stopped working right after I fixed another issues on this Toyota. When Toyota turn signals don't work, sometimes it can be a bad turn signal flasher , a bad combination switch, a bad hazard switch or sometimes it can be something else. The exact vehicle in this video is a 2006 Toyota Sienna CE.
Other videos on this Toyota:
Toyota Stuck in Park: • Toyota Stuck in Park/W...
The Mechanic Broke My Car!: • The Mechanic Broke My ...
Be sure to subscribe for more tool and car repair videos!
/ bigdog50001
/ bigdog50001
/ bigdog50001
Disclosure: This channel earns a small commission using some of these links - at no additional cost to you.
The Big Dog 50001 Automotive Channel Store can be found here: www.amazon.com...
Tools and Parts:
Launch Scan Tool: amzn.to/2ObRQV4
Fuse Saver: amzn.to/37EgDJ9
OTC Test Light: amzn.to/36GpiJQ
Crimp/Heat Seal Connectors: amzn.to/2GzXexm
ATM-LP Fuses: amzn.to/2RB87VU
ATM Fuses: amzn.to/37CJ2PL
Want a free Big Dog50001 sticker? Send an email to bigdog50001@gmail.com requesting a sticker. Sorry, no international addresses or automotive questions.
Have something you would like to send to Big Dog50001?
Send it here:
Big Dog50001 Automotive Channel
P.O. Box 726
Cortaro, AZ 85652
2020 Epidemic Entertainment. All rights reserved.
Disclaimer:
Due to factors beyond the control of the Big Dog50001 Automotive Channel, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. The Big Dog50001 Automotive Channel assumes no liability for property damage or injury incurred as a result of any of the information contained in this video.
The Big Dog50001 Automotive Channel recommends safe practices when working with power tools, in on or around automobiles or other vehicles, automotive lifts, lifting tools, jack stands, electrical equipment, automotive modules and systems, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of the Big Dog50001 Automotive Channel, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not the Big Dog50001 Automotive Channel.
*Tools and Parts*
Disclosure: This channel earns a small commission using some of these links - at no additional cost to you.
Launch Scan Tool: amzn.to/2ObRQV4
Fuse Saver: amzn.to/37EgDJ9
OTC Test Light: amzn.to/36GpiJQ
Crimp/Heat Seal Connectors: amzn.to/2GzXexm
ATM-LP Fuses: amzn.to/2RB87VU
ATM Fuses: amzn.to/37CJ2PL
The Big Dog 50001 Automotive Channel Store can be found here: www.amazon.com/shop/bigdog50001automotive
You are just awesome. I went in to get car inspected and thought I was going to have to buy a switch motor. I don't know what they did, but my signal lights did not work when he sent me away with a passed inspection. The hazards still work and I can find the screws to get to that part easier. You just eased my restful sleep tonight. Thank you.
I feel I am learning more about circuit from your repair video than what I learned from electrical engineering class. Thanks
Thank you, I appreciate the comment!
Interested
Not sure
Faccttsss
Me too
You know when people try to explain these things they kind of gloss over the major things you need to know which makes me think they either aren't that knowledgeable or are simply bad teachers. This is one of the few wheres its very obvious you know exactly what you are talking about and explain it very clearly. Thanks man.
Many crap videos getting millions of views and good videos like this getting only hundreds 🤔. Thank you for making informative videos.
I appreciate the comment, thanks!
Good to see a video where someone is throughout in his work and not some parts changer.👍👍👍
Thanks 👍
I was going crazy diagnosing my turn signal problem until I saw the part in the video where there was hack wiring. I checked the trailer harness wiring and quick splice connectors were used and the wire to the rear turn signal had broke off. You saved me many of hours of troubleshooting. Thank you!
Dave, obviously I hope the customer understood it was a separate repair. Good video and thanks for walking us through the wiring schematic. Thanks Dave ❤️
They did, thanks for the comment!
Great informative video! Love how you went the extra mile and didn’t cut corners. I have a 2009 Toyota Tacoma and I’m having this problem. I’ll be following your video step by step.
Fuse saver has saved my butt a crap ton of times on customer vehicles saved me alot of time
Mind blowing problem solving skills. Awesome walk thru hopefully I can solve my issue.
Thanks 👍!
My brother that video was super comprehensive and you are hilarious! I'm trying to add a load equalizer to my 2000 Toyota Avalon XLS and I was researching how to do it and came across your video. The second I saw you pull out a wiring diagram, I knew class was in session! Thank you for taking the time to make this professional troubleshooting/repair video. Although it wasn't exactly what I was looking for, it was a pleasure to watch!
The turn signals and hazards on my 2001 Corolla stopped working after I replaced the RF turn signal bulb. I was at my wit's end on how to figure out the problem, and I did not want to pay my mechanic $120+ to diagnose and fix what I knew had to be a relatively cheap fix. I watched several Corolla specific videos which were of no real help before I stumbled upon this video. The Sienna here was exhibiting almost identical symptoms as my Corolla when the turn signals failed.
After watching this video I was able to step-by-step diagnose the issue on my Corolla and, more importantly, fix the problem! In my case I evidently caused a short in the RF turn signal bulb socket which in turn blew the turn signal and hazard fuses. I disconnected the socket, replaced the fuses, and voila, the signals were working again (other than the right side flashing quickly as there was no front bulb). Replaced the plug and bulb (I actually replaced the entire turn signal assembly as the glass was cracked on it anyway) and everything works perfectly again.
THANK YOU so much for creating this clear and concise video detailing how to diagnose and fix this problem. Even though it was for a different model, it helped me out tremendously!
That was a quick way to isolate the right side. A very organized approach Dave. I like your style.
Thanks Wyatt!
Thanks for your help! This video is so methodical. In my situation, I ended up replacing the 15 amp HAZ fuse in the engine bay. My turning signals are now back up and running. Thanks!!
I like your analysis, common sense and calm approach. Thank you.
I appreciate the comment, thanks!
I am watching your clear videos and at the same time learning lot. I appreciate your services rendered to our society. I am pray for you and your family for good health and wealth. Thanks.
I appreciate the comment, thank you!
work smarter not harder💁 about to start trouble shooting on my 06 tacoma. Non of the turn signals work cause it keeps blowing the fuse. Definitely using your tips & tricks and least invasive way to get it figured out😉. Amazing video btw!
Thanks 👍!
thanks for the extremely thorough yet easily understandable explanation of the steps needed to prevent just random part swapping. I had this exact issue in my 2006 4runner...well aside from the goofy wire tap. I was going to go straight to swapping the flasher when it was just a bulb.
Just had this on a 2005 Hilux here in the Aus outback. This vid saved me weeks waiting for a mechanic and likely hundreds of $$.
Love your work mate 🍻
Thanks for the CLEAN descriptions. Your video and methodology spoke to me like you were wired into my brain. I seen the LIGHT! Thanks for puting this vid on here and the hard work put into it. It was also easy for me to share this with my new teen driver and they were able to comprehend as well.
Nice explanation. It's so easy to understand. I couldn't explain it any better. Finally solved my corolla's problem with the turn signal that has only one side that works. Thanks!
How did you manage to fix it, my estima has a issue where the left turn works, hazard light work fine but the right turn does not work
Dave, had the same problem. No turn signals, no hazard. Checked the hazard fuse ,it's ok, checked the turn fuse, it's ok. Checked all bulbs front and back, 1 bulb out. It's a small one from the right rear. No broken wires in any of the lights. I have a 2000 camry le 4cyl. I'll replace the bulb tomorrow. Will let you know. Great video ! Thanks. Hope it's not the flasher..... Nino
Did you figure it out? Thanks for the comment!
@@BigDog50001 Hi Dave , yes I did. It was the relay. It was behind the kick panel on the driver's side. You have to look up a little to see it. I put in an after market relay, ( cheaper than Toyota), it works fine, but you hear no tick when the light flashes. I went thru everything before I checked the relay. Your video is a good way to track the issue down. Thanks
hey man just want to say thanks for the detailed video. I was resigned to getting a sparky to have a look at my issue which happened to be the same as yours, however you inspired me to have a crack at it and I was able to diagnose - well done mate thanks
Awesome! Thanks for the comment!
Skillful mechanic, genius, again fine work.
Thank you, I appreciate the comment!
Very useful video, I am studying automotive electricity, I hope you have many videos about automotive electricity.
thank you very much. i am from vietnam
👍
I have issue with my 2.4 camry turn signals and hazards not working. This video really will assist solve the issue.
great video. loved how you explained the circuit.It shows that you are a good trouble-shooter
This is an amazing high quality video troubleshooting step by step and arrived at awesome result at the end. I am struggling with similar problem on a similar vehicle 2007 Toyota Sienna AWD. Hazardous light is working flawlessly all the time but the turn signals are not working and the battery indicator at the time of ignition is not showing either. Up on investigation 15 amp hazardous fuse is fine but 10 amp GUAGE1 (under the dash) fuse is blown up on just turning on the ignition without starting. I disconnected all four indicator lights (front and back) and put the ignition on, 10 amp GAUGE1 blown again. I checked the wiring under the dash dash fuse box and the console wiring and it seems to be intact. In another test, put a new 10 amp fuse and turn the ignition on, the battery indicator and turn signal worked fine however when the key tuned to start position and started the car the indicator light stop working and the fuse is blown again. Bottom line sometime the 10 amp GUAGE1 fuse is blown when the ignition is turned on and some other time when the ignition is in the start position fuse is getting blown.
Both cases engine starts fine. Any recommendations to test would be greatly appreciated.
Great teaching session and how to view a problem while at the same time expanding your mind with investigative diagnostic thinking. Very well done, this really helped me a lot.
Definitely subscribed to your World.
Oh, I bet you found the same condition on the other side too, like maybe someone was trying to pull off a temporary trailer light set up or something.
Thanks 👍!
Great video, just for others watching, if you have trailer light plugs on your car that is another possible short location thats where my short was. Thanks for the vid
👍
Thanks dude, was pulling my hair out.
Ripped apart the old relay as I was removing it because I have the hyperflash with leds, but it shorted.
Put the new one on and nothing, checked both fuses and they looked fine, but I should've started with the test light, would've saved me the headache.
Ended up being the hazard fuse under the hood and working good now.
👍
You're a good teacher, great communication. Thank you. My issue is the turn signals don't work, but when I turn the hazard lights on all of the lights come on. :)
Have a 2006 Toyota Sienna just ran across your video I had the exact same problem thanks a lot I appreciate your help
Great video. My right blinker light on the dash does not blink, the hazards only left works. All other outside lights work fine. What would cause this to happen? There are no bulbs in the dash.
On some toyota models the right and left blinkers are on a separate circuit and fuse then the hazards
That's why it is usually a good idea to get a wiring diagram!
@@BigDog50001 I agree
good video, I played it at double speed and it was great, the explanations were the best.
Thank you Dave. Good job. Have a blessed and safe week.
You too, thanks for the comment!
This could be the best video I’ve ever watched on TH-cam. 😮
Thank you for the video - you’ve just helped me fix my RAV4 gen. 5. Turn lights were not working and it was a blown HAZ fuse.
👍
I very much appreciate you explaining how they are wired, I just blew the 15 amp fuse you replaced whilst trying to wire in trailer lights
👍
Thankyou for help literally skipped through and solved the problem within 5minutes appreciated 🙏
👍
This was exactly what I was looking for! Thank you for helping me fix the blinkers and hazard lights on my 2011 Toyota Highlander! You are awesome!
I had a similar issue on one of these same vintage Siennas where the brake lights would blow the fuse but not all the time. Took me a while but finally tracked it down to bad aftermarket tail light socket/housings. Try telling someone they need to buy two new tail lights when the old ones look just fine. Two used OEM tail lights fixed the problem, though.
Thanks for the input!
Did you run continuity test on socket to determine it was bad?
Thanks for the video, I'll check the fuse and and the rear light to just make sure. Would have to go to a technician to fix the wiring if the wire aren't done right
My car has the same thing now I need to find the wire that's grounding. My battery drains every time I turn it off. You think that's the cause of it?
Same problem with the fuse blowing only on one side. Thanks
Hard to say, it could be the same problem creating both symptoms but it could also be two different issues. Probably needs some troubleshooting done.
Good evening Sir,
Thank you very much for your
Tutorials I've learn to test this
Probs.
👍
thanks for your time explaining all of this. Very helpful..
Great explanation, you could be even a teacher 😊
Excellent video. The repair video is great quality and provides a disciplined approach. Well done!
They should ve told you about the wire. But if they did you would nt have made this very informative and GREAT video!!!
Another excellent video. Big Dog schooled old dog yet again.
Thank you, I appreciate the comment!
Well done. I'm working on my own Toyota tail light problem. I subscribed.
Thanks and welcome!
Many thanks. It was the gauge fuse on my Lexus RX.
Good that you checked the other side as well. Thanks for the vid. Awesome!
This is a mechanic I would like to take my car to.
Quality instruction. Thanks alot.
Thanks 👍!
I've got an 06 Toyota 4 runner with the left rear turn signal out. The front left is working. I switched the socket and bulb from left to right side and the left works on the right side. Any suggestions to help. I've been trying to figure this out for one year with not luck. Thanks, Dave
Cool tutorial. By the way, how were you able to get the electrical diagram? I need one for my Toyota Sienna 2011
My solution was very simple. I had neglected to turn off the hazard flashers before turning the car off, thus neither signals nor the hazard flashers worked once the car was restarted. Once I made sure that the hazard button was no longer pressed, all flashers were fine.
Hi I recently ran into a problem on my 2002 Toyota celica I went to turn on my turn signals and got nothing no lights on the dash blinking or signals working. My hazard lights will turn on and work no problem I tried swapping the fuse and the relay for it and still no fix do you have any other ideas as to what it could be? Thank you
Did you ever figure out this problem? Having same issue with my 2000 toyota Camry
Having the same issue on my Toyota Yaris 2011
Same with hilux
Same with my 2005 Caldina
Same with 2000 Celica t23
Hello.
My blinkers and hazards dont work at all. Could it be the flasher relay or a broken blinker handle?
I watched your video and it is extremely helpful. My car was broken into and ransacked. The radio was ripped out and now the blinkers do not work. I dont think they are related but more info the better. The thief's could have yanked or broken the handle during the crime.
The fuses look intact.
Thank you for any suggestions.
Great to the point instructions, i have come across a lot of the those cheap nasty scotch lock connectors in the past in my repairs of customer's wiring.
especially in rear where some aftermarket towbar fitters trailer plugs. have just done a quick fix ... i hate them they bound to fail.
also now coming across al ot of fixers with panel beaters using same method with bull bar fitments. gahhh... but always have happy customer after its fixed.
get job on the fix.
i look forward to more content.
Good explanation with the diagram and good way to go about diagnosing
Thanks Antonio!
Thank you for the video, it was just what I needed to fix my car! I had a bad ignition switch fuse.
👍
Interesting video. I am having a similar issue. The right blinker does not work at all. Outside right front and back turn signals flash fine. Pulled instrument panel and it’s circuit board with no bulbs. Do you have any suggestions as I think it might be a ground as well versus a dash issue. The hazards have the left blink only but all outside work fine. Hummm
I hate those vampire taps! Good find and fix Dave!
Me too, thanks Mike!
what might be the problem if the turn signals not working but the hazard works
Step by step diagnosis, well explained
Thanks for this video, I fixed my problem by watching it!!
Good day,
I recently ran into a similar issue with by 2022 Can Am Spyder RT Sea to Sky. It started out with right turn signal malfunction, then daytime running lights. I replaced the 15amp fuse for daytime running lights and the right turn signal would flash all lights. The fuse failed again. Now it blows as soon as I turn on the bike. I noticed the fuse I used on the 3rd and fourth attempt that failed immediately was not the same as the original brand so I purchased a hand full of the original type. What do you think the issue is ? I am somewhat trepidatious about trying again for fear of causing any damage.....your insight would be greatly appreciated.
Nice diagnoses and repair Dave
Thanks Jim!
Man, I got a 2015 camry and signal lights just stopped working while I went to the store. I checked the fuse under the hood and it's good. I can hear the sound but no lights at all.
Time to track mine down the same way. But I think both fuses on my 2000 avalon are good.
The same thing happened to me but a quack electrician just opened under the steering wheel and changed I think the flasher but whatever is going on is still the same, the left trafficator light doesn't come up all the time and the hazard light doesn't come up at all too
Please should I try it out just like yours though yours us the right side
I hate them blue piercing connectors
You are me both!
Good find BigDog. That certainly does not come back to you.
Yes, left needed attention too for the trailer flashers tat used to be wired in there.
Definitely an existing issue!
Hi ,thank you for the video and your knoledge.
Is the same diagramm for the Toyota Hi-Lux 2009 ? If is possible can you send the wiring diagramm ?
Have u ever dealt with or do you know why a 2000 toyota solara car hazards and turn signals won’t work after charging the fuses and relay ?
Thoroughly Enjoy your videos Dave. Love watching how you problem solve and diagnose these issues.
Thank you, I appreciate the comment!
@@BigDog50001 I plan on purchasing a few tools from your Amazon Link. Anything special I need to do for you to receive credit?
Dang it I need to know how to locate and change the blinker relay. Any help with a link?
Got similar problem now. Left side turn signal flashes once. Thats it. No fuses blown. Disconnected all turn signals. Found no obvious short to ground. Any idea whats going on?
Nice video. Thanks.
Thank you, I appreciate the comment!
I have a question if both turn signals not working and hazardous work will that mean there’s a fuse blown or a wire grounded ??
Nice,smooth diagnostics....
Thank you for the comment!
What about a 04 turn signal toy sienna xle limited still clicking after the turn is made? Drives me nuts! Sometimes if you turn the van off it stops. Thx
good diagnostic and fix.they had that problem for will i bet.
I think it has been there for quite a while too, thanks for the comment!
I'm watching this video to learn how to get a constant power while the turn signal is on to power up my after-market side mirror camera for my 2007 Sienna. I wish I can get my hands on a diagram. I'm still not sure where exactly to tap.
I replaced all my turn signals front and rear in my 2010 corolla with LEDS. Put a new flasher relay and so it isn’t hyper blinking. Worked for about a month but I have lost my right turn signal. Checked my fuses didn’t look blown so I put a 20 in. Stopped working but now everything including hazards are working. Only thing not working is my right turn signal. Left works, hazards etc.
Any ideas on what it could be? Do I need a higher fuse? Never had any issues before I replaced bulbs and flasher relay. Also my cruise control will not turn on.
Great anaysis!
Thanks 👍!
@@BigDog50001 I fixed my car for zero $ based on your process. Thank you so much. Different car, different problem, but your approach did it. Downloaded the wiring and figured through it based on clues. Teach a man to fish...
Excellent video!!
I fixed it! Thank you!!
Nice one Big Dog, thank you for your work, God Bless 🙏
Pretty late to the party. Long story short had the dash apart working on the fan selector. Had to disconnect 4 way flashers to get access. So never fixed but had to use the car in an emergency and quickly slid dash in loosely and went off. Signals did not work at all (all 4 front and back). Thats because i never plugged the 4 way flashers in cause who cares right. Quick trip. Well you need em plugged in to complete the circuit and have signal lights. 1:15 into the vid and i saw the chart and it suddenly clicked. Thanks for being my muse.
This helped me out a lot
Thank you very much
Glad it was helpful, thank you for the comment!
Toyota sienna 2001 turn signals and hazard lights not working replaced fuses it worked, but now not working again what could be the fault you response will be highly appreciated thanks
What fuse is the one that went out under the hood?
It has been a very helpful video. Thank you for sharing. Appreciate that very much.
Excellent video as always. Thanks for sharing.
I appreciate the comment, thank you!
I'm new to your channel but I love your videos!
🎯 100% accurate guidance; Thank You