Vendo esse vídeo de reforma do alto-falante, além da montagem da caixa amplificada, e um outro de conserto e restauração de um amplificador, me lembrei dos meus tempos de bancada, quando eu era mais jovem....trabalhei muito com reparos de equipamentos de áudio diversos e reformas de alto-falantes....Você só consegue fazer um trabalho desses se tiver paz e sossego, sem ninguém pra perturbar, pedir sua atenção ou te cobrando algo...até a chuva e som dela mostram a paz desse lugar pra se trabalhar...excelente vídeo...me trouxe boas lembranças...
The rebuild is very nice. The sound is wierd... I think the mic was swamped with to much sound?? If you treat the cone with a fluid and the cone becomes heavier you alter the moving mass from the unit and the Fs from the speaker. Did you account for that??
i always reinforced the rim of the speaker outer cone with a few coats ov PVA wood glue.as i play a lot of dub bass n it needs reinforcing...just a thought...great vid,bought back memories of building me cabs back in the days
I think what you do is great. I restore and modify inexpensive electric guitars and basses, occasionally an amplifier. Your level restoration is inspiring. You might want to speed the video up in some spots, just to help keep us captivated. I'll admit, I turned up the speed on this video and didn't miss anything. Good Job! 👍
The editing to show the storm to explain the rain was brilliant. Keeping the story consistent so that we don't get thrown out of the "pocket." Thanks for the detail work!
вроде руки из правильного места растут, но есть несколько вопросов... первое - зачем пропитывать диффузор??? второе - стенки ящика надо делать в три раза толще!!! если хотите 2 kW снять, третье - трансформатор ватт 800 не более... так что 2 kW не получите. четвертое- без активного охлаждения ваши транзисторы стрельнут ровно через полчаса!!! пятое - на хрена щель????? у вас ЗЯ с фазоинвертором... кроме треска корпуса ни чего не слышно, столько трудов и в мусорку.
У них провод сопротивлением больше , так что с малым железом они получают мощность в разы больше. Посмотрите на трансформатор от микроволновки. А он почти два киловатта.
И ещё. Советский ватт, - это максимальная мощность динамика, при которой ещё практически нет искажений звука. Иностранный ватт, - это такая мощность динамика, при которой он разрушается за час. Точно не помню, но иностранный ватт раз в пять завышен по сравнению с советским. Китайский "перестроечный" ватт - мощность, разрушающая динамик за 3 секунды. Завышена по сравнению с советским ваттом раз в 50-100.
I love watching you fix what one without knowledge would deem as unfixable. One thing I'd like to see is approx how much it would cost to do each repair....as in what you would charge the end user of the repaired component or equipment to do it. And with these larger subs...it seems like it takes a good amount of time to do a total refurb/restoration! How much would it cost to buy this or a comparable sub new vs how much would you charge to restore this one to good as or maybe even better as new condition. Keep up the great content!!!
The black glue around the coil to cone join is often softened by acetone, but that looks like a JBL in which case the most likely solvent is naptha (lighter fluid) Nice speaker. Well worth rebuilding.
hay 4 factores muy importantes que hay que tener uno de ellos es la geometría de la ubicación y profundidad de la bobina sin mencionar el calibre del cable buen trabajo saludos desde colombia
`It is a great looking piece of kit and your craftsmanship is top notch,however.......lol I wouldnt put that piece in the front with the slot because I think it would cut off the really low long wave forms bigger than the hole.Most good designs offer an unobstructed path for low/large waves. the other slot is fine its just putting out the "backstroke" of the box. nice bit of kit tho!!!!
Bonjour de la France Mr Electricité.......... Très beau travail, mais attention la bobine mobile est trop basse, ça va taper dans le fond de l'entrefer...............
Excellent!!! Just one question: what kind of liquid do you use to remove parts such as seals, suspension, diaphragm, etc...? and what type of glue do you use for reassembly?? Thank you
Ive experience also replacing speaker cone but didn't try assembling subwoofer but it much better if the hole youve made for exhaust of air must be circular and alike to the size of magnet so that the sound is pure bouncy rather than cracky.
Terrific 💯 PERCENT Job with that sub woofer build I really appreciate your talent and skill craftship Wow that is some high-quality skills you have to make that subwoofer If you were to sell that subwoofer how much would you sell that type of subwoofer Great job 👍👌😊
Nabangit mo sir na di ka nagamit ng monitor out what if may acoustic band ka pwede na yan di ba. if needed ng monitor may effects send to monitor ba yan?
My dad has a pair of woofers that look like this, legand has it that I sat in them when I was a baby! I guess that was a mistake that my dad only made once!😄😄😄
La bobina esta muy mal puesta ya que se tiene que dejar unos centímetros más arriba pero el l dejo al raz del centro del magneto por lo cual la bobina va a chocar con el final del imán y se le irá quemando poco a poco las puntas lo cual será un daño si o si
Membrane...spring?. How about surround, dust cap and spider? He either used acetone (like nail polish remover) or naptha (lighter fluid), depending on the type of glue.
Vendo esse vídeo de reforma do alto-falante, além da montagem da caixa amplificada, e um outro de conserto e restauração de um amplificador, me lembrei dos meus tempos de bancada, quando eu era mais jovem....trabalhei muito com reparos de equipamentos de áudio diversos e reformas de alto-falantes....Você só consegue fazer um trabalho desses se tiver paz e sossego, sem ninguém pra perturbar, pedir sua atenção ou te cobrando algo...até a chuva e som dela mostram a paz desse lugar pra se trabalhar...excelente vídeo...me trouxe boas lembranças...
A pior coisa que tem é da gente está se dedicando a algo e vem uns pra azucrinar nos ouvidos da gente!
About time for a new cutter in the router!
The rebuild is very nice. The sound is wierd... I think the mic was swamped with to much sound?? If you treat the cone with a fluid and the cone becomes heavier you alter the moving mass from the unit and the Fs from the speaker. Did you account for that??
His mic and TH-cam playback equalization don’t do justice to the sound.
مشاءالله تبارك الرحمن
Para escuchar guarachas santiagueñas hasta el amanecer en navidad hasta año nuevo, genial man...
i always reinforced the rim of the speaker outer cone with a few coats ov PVA wood glue.as i play a lot of dub bass n it needs reinforcing...just a thought...great vid,bought back memories of building me cabs back in the days
I also liked the rain on 10:30 and in the background!
I think what you do is great. I restore and modify inexpensive electric guitars and basses, occasionally an amplifier. Your level restoration is inspiring. You might want to speed the video up in some spots, just to help keep us captivated. I'll admit, I turned up the speed on this video and didn't miss anything. Good Job! 👍
The editing to show the storm to explain the rain was brilliant. Keeping the story consistent so that we don't get thrown out of the "pocket." Thanks for the detail work!
Wow a stomping subwoofer restoration
I like you and profesional and I have subscribe. I am to Indonesia 🇮🇩.
Great if you like uninformative, boring videos with no narration.
You fu*ked up English
вроде руки из правильного места растут, но есть несколько вопросов... первое - зачем пропитывать диффузор??? второе - стенки ящика надо делать в три раза толще!!! если хотите 2 kW снять, третье - трансформатор ватт 800 не более... так что 2 kW не получите. четвертое- без активного охлаждения ваши транзисторы стрельнут ровно через полчаса!!! пятое - на хрена щель????? у вас ЗЯ с фазоинвертором... кроме треска корпуса ни чего не слышно, столько трудов и в мусорку.
У них провод сопротивлением больше , так что с малым железом они получают мощность в разы больше. Посмотрите на трансформатор от микроволновки. А он почти два киловатта.
И ещё. Советский ватт, - это максимальная мощность динамика, при которой ещё практически нет искажений звука.
Иностранный ватт, - это такая мощность динамика, при которой он разрушается за час. Точно не помню, но иностранный ватт раз в пять завышен по сравнению с советским.
Китайский "перестроечный" ватт - мощность, разрушающая динамик за 3 секунды. Завышена по сравнению с советским ваттом раз в 50-100.
Это Бандпасс
Диффузор он видимо не пропитывал, а покрасил.
WOW!!! Amazing 🙌Work🙌🎶🔊
N 1💯🙏
Very impressive!
I love watching you fix what one without knowledge would deem as unfixable. One thing I'd like to see is approx how much it would cost to do each repair....as in what you would charge the end user of the repaired component or equipment
to do it. And with these larger subs...it seems like it takes a good amount of time to do a total refurb/restoration! How much would it cost to buy this or a comparable sub new vs how much would you charge to restore this one to good as or maybe even better as new condition. Keep up the great content!!!
The black glue around the coil to cone join is often softened by acetone, but that looks like a JBL in which case the most likely solvent is naptha (lighter fluid)
Nice speaker. Well worth rebuilding.
Not a JBL. While having the same basket JBL doesn't have this cone or motor on their 18s
Very good 👏🏿👏🏿👏🏿👏🏿👏🏿
Nice time to do the job inside or under a cover when raining! The rain is nice!
Congratulate at your work
😎
Такой дома включиш крышу поднимет👍👍👍
Great work interesting style woofer set up with built in amplifier
Interesting build, with a bandpass enclosure.
I would have went with a transmission line, and pushed it into the deep bass territory, just for fun :D
It looks great and you did a great job making that subwoofer
I really appreciate your talent and ingenuity! Today I learned from you. really smart,
Great job Sounds Great.
Very good👏👏👏👏👏
Well done, great video 💪🏻😀
Excellent job.
hay 4 factores muy importantes que hay que tener uno de ellos es la geometría de la ubicación y profundidad de la bobina sin mencionar el calibre del cable buen trabajo saludos desde colombia
Perfect work
I’ve watched you restore junk this ain’t so much junk but still ..Great job
im watching and like ❤
Nice video, but you're really messing with my OCD at 6:44 when you almost did the cross pattern tightening, but stopped half way xD
great job. perfect
I would like to know the design of the box. Could you give me the measurements?
😊😊😊😊😊😊😊😊😊
nice Job very good thx for your Video i like it
`It is a great looking piece of kit and your craftsmanship is top notch,however.......lol I wouldnt put that piece in the front with the slot because I think it would cut off the really low long wave forms bigger than the hole.Most good designs offer an unobstructed path for low/large waves.
the other slot is fine its just putting out the "backstroke" of the box.
nice bit of kit tho!!!!
Box speaker nta mantap sob...❤
Splendid!
Great job💪👍👏😁
He is highly skilled in speaker restoration
Dịch
I have built loads of disco speaker boxes in the past. I had forgotten how much effort they take.
Bonjour de la France Mr Electricité.......... Très beau travail, mais attention la bobine mobile est trop basse, ça va taper dans le fond de l'entrefer...............
very nice work. not a fun of box texture. you should have raised the coil a bit. also fasten the heatsink and reverse the on/off switch.
The coil was put in bottomed out. Got to have equal distance centered on motor for linear excursion.
i heard it popping
Indonesia bagian Jawa Timur hadir lhurrr
Nice idear. But not efficient. Same System like Electro voice in the earlier 90s. Better build 3 reflex enclosures and stacking. 8db more!!!👍👍🇩🇪
U r the heeeeero..❤
Wow that was a cool video great job
Bom dia valeu 👍 muito bom gostei
Excellent!!! Just one question: what kind of liquid do you use to remove parts such as seals, suspension, diaphragm, etc...? and what type of glue do you use for reassembly?? Thank you
Przepiękne jest ten stary zabytkowy głośnik odrestaurowany pozdrawiam serdecznie 👍👍👍👍👍
What's that mysterious liquid he's using in the beginning? Acetone? Alcohol?
Начал просмотр с середины. Подумал, что будку кобелю на зиму строит, а оно вон что оказывается☺. Кстати, а у них вообще есть собаки?
Hi, i'm from Brazil...I lke this channel very much... Congratulations and thanks.
Người Việt Nam mà làm TH-cam hay nè
I am one of your subscriber.from the Philippines
14:08
What is it? Is there any
Whaglue or silicon oil or paint?😮 Why not paint from both sides?😅
i like the screw holder
Nice work, but the heat sink will rattle, not fastened.
Show muito toop
Mantab 🙌
❤great Chanel
You have to weld even the 2 giant condensators !
😱😱😱😱หลังคาสั่น
Ive experience also replacing speaker cone but didn't try assembling subwoofer but it much better if the hole youve made for exhaust of air must be circular and alike to the size of magnet so that the sound is pure bouncy rather than cracky.
As long as that copper coil is ok.Thats the main part needed!
Um grande ❤
QUE ESPETÁCULO DE HABILIDADE E SABEDORIA!
When i first saw it i was thinking my 15 looks pretty damn simlar wtf are you talking about.. then you measured it 😂😂 holy crow!
Qual o nome desse produto gostaria de saber por gentileza
Terrific 💯 PERCENT
Job with that sub woofer build
I really appreciate your talent and skill craftship
Wow that is some high-quality skills you have to make that subwoofer
If you were to sell that subwoofer how much would you sell that type of subwoofer
Great job 👍👌😊
11:00, where U order this one? Where is the best factory?😅
Good job but I will like to know the system brand or model.
Thanks
7:07 What U use for for screw heads? No names :(😢
Well done great Job congratulation and thanks......
Exelente,, Felicidades,
It sounds very good, is it a 3rd order band pass design?
Maşallah cok iyi oldu
VERY LOW MASS GLUE, MAYBE SOME TYPE OF ACETONE ? AS REMOVER ?
1:14
What U use to remove old glue?
Nabangit mo sir na di ka nagamit ng monitor out what if may acoustic band ka pwede na yan di ba. if needed ng monitor may effects send to monitor ba yan?
Amazing restoration! it would have been awesome to see what was each element/tool/ingredient/component, tho.
Végig néztem a teljes videót. Szép munka. Dee. Mi volt a végén az a csattogó hang??
I'm from Indonesia, I like your channel, and I'm learning...
Thank you
AMAZING
My dad has a pair of woofers that look like this, legand has it that I sat in them when I was a baby! I guess that was a mistake that my dad only made once!😄😄😄
TOP Parabéns
Top💪
let's think about cleaning....soda blasting or sand ?.....I'm just giving you a hint....great as always:).......ps.Much faster!!!
You build some very nice speaker boxes! I don't care what people say about you!
What's the amplifier model that you installed inside the woofer?
Otro gran trabajo! Felicidades!
La bobina esta muy mal puesta ya que se tiene que dejar unos centímetros más arriba pero el l dejo al raz del centro del magneto por lo cual la bobina va a chocar con el final del imán y se le irá quemando poco a poco las puntas lo cual será un daño si o si
Vc conserta e vende
Gd🎉❤
What preparation do you use to remove the membrane and spring? Please help... Regards
Membrane...spring?. How about surround, dust cap and spider? He either used acetone (like nail polish remover) or naptha (lighter fluid), depending on the type of glue.
Hello, could you tell me which product, do you use to take off, thank you to you
Wow!😮😮
Good
6:35 Glue for magnet?😮
Buenas tardes que líquido usas para despegar tan rápido los conos de las bocinas
Acetone hay còn gọi là xăng thơm