ฝัง
- เผยแพร่เมื่อ 7 พ.ย. 2020
- 參考影片
• Переделка зарядного ус...
Replacing part:
1. Capacitor 400V100uF (replacing 200V100uF)
2. Thermistor NTC 10D-9, 10Ω 2A (Replacing the Jumper at J1 position)
New part
1. Varistor 14D431K (one end is soldered to the live wire after the fuse, and the other end is connected to the neutral wire)
俄仔話改完之後實際上可行110-230V, 本人已實測可行220V
需準備的零件：
代替部分
電容400V100uF (代替200V100uF)
熱敏電阻NTC 10D-9, 10Ω 2A (代替J1位置上的Jumper跳線)
新增部分
壓敏電阻14D431K (一端加在火線的fuse後, 另一端與青線連接)
配樂：
PaperClip - Beeeep!
PaperClip - CAVALAR
PaperClip - KINGSTON
Licensed under CC BY 4.0 - แนวปฏิบัติและการใช้ชีวิต
![[#SHORTS CLIP] ครูอึ้ง กรรมการอึ้ง ฮ่าๆ l ซานิเบาได้เบา l One Playground](http://i.ytimg.com/vi/qeBTuMJs4t0/mqdefault.jpg)
正
It works! Cheers mate.
Congrats!!
Hi, thanks for the video.
Can I use 10om termistor type sck-103 and veristor type TVR-10471?
Exelente la informacion tengo un cargador con ese mismo problema boy atratar de hacerle esas modificaciones aver como me resulta saludos desde panamà 👏🙋♂️🇵🇦
Its possible to use varistor 14n431k ? Thank youp
Thanks for sharing, a query, why do you replace a bridge with a thermistor, I got lost in its purpose, if when heating it behaves more like a short circuit, what is its purpose? thanks greetings
See if my explanation makes sense to you. When charging rapidly, the circuit heats up and causes volt dropped. Resulting in increasing the resistance of the circuit. A NTC can just compensate this issue in rapid charging by lowering the resistance when heating up. It maintains the performance of the charger in rapid charging.
@@hinchan0131 thanks for your prompt response friend, it is strange then that they have not included it from the factory, do you know exactly where that bridge goes, I mean what component does it act on?, thanks regards
Alguien sabe convertir un cargador modelo Dcb1104 de 110v a 220v
Привет. Можно с этим зарядить 6 или 9 амперный аккумлятор?
Hi Hin. I have made all these changes as described in the video but the charger doesn't work at all. What might be a reason? Thanks. Jacob
Hi Hin. Sorry... it was a problem of the battery. Everything works fine after the conversion.
Super!!! Like!)
Hi Hin, can you please attach links for purchase of the necessary electronic components needed? Thanks!
I bought from Taobao, which may not be available in your country. Same parts could be found in Amazon as well.
@@hinchan0131 Thanks Hin, I found these components on AliExpress but I don't know if it's high quality, so maybe you can recommend me some brands of this components.
can you make any dewalt charger to work like DCB119 vehicle charger?
Sorry, I have no idea
Can anybody tell me the exact location or circuit points where ntc resistor be placed, it cannot be figured out in the video. thanks
Look at 0:55 of the video, I have put the ntc resistor symbol on the circuit board.
@@hinchan0131 million thanks and your video is excellent
dewalt設計咁複雜 美沃奇易改好多
what are the odds you can give instructions in english, at least the parts used
Replacing part:
1. Capacitor 400V100uF (replacing 200V100uF)
2. Thermistor NTC 10D-9, 10Ω 2A (Replacing the Jumper at J1 position)
New part
1. Varistor 14D431K (one end is soldered to the live wire after the fuse, and the other end is connected to the neutral wire)
Is it clear enough for your?
Yes thanks a lot man
想問其他型號 都係咪咁改 謝謝