I have a 2017 chevy malibu LT i had mine replaced, but they didnt program it with my vin, so my remote start doesnt work. Can i have it reprogrammed properly. Or can i purchase a new one and have you program it properly?
Thank you for this! Does this work on the 2.5 Ecotec LT1 engine version as well? Also do you have a programming video for it?
Yes we do have these Body Control Modules in stock available however we do not have a programming video for it.
Helpful video do you need to reprogram/reflash the bcm our is its plug and play
Hello, please can you help me, I was able to remove the last 3 connectors: green, blue and white, but I can't get the ones on top out. Please can you advise me if you have any tips or tricks? Thanks for your advice.
Any idea how to reprogram the bcm for a 2010 malibu without taking it to the dealer?
Does it need to be programmed. Cause i want to buy one and i want to check if its working properly before paying
Hello, I have a question, I need to change the BCM on a 2012 Malibu but I don't know if I can put any BCM in or if I need to check something for compatibility?
Can you show us the bcm programming?
Programming of certain modules will be available for ecuteam subscribers in the future.
Do you need to unhook the battery on the car first? And are you able to get a bcm preprogrammed.
Only the negative wire you can unhook. Then you can proceed to the next steps.
very good video, can you please help me to know if the BCM of a 2013 Malibu is good, since it shows me the following errors, I will greatly appreciate your help. Greetings The errors Car Scanner ELM OBD2
Version: 1.106.0/401060/GP
DTC report
Connection profile: Chevrolet OBD-II / EOBDDate: 25/05/2024 06:49:11 p. m.
VIN: 1G1195SA2DF263812
============================
OBD-IIOBD-II
DTCs: 8
----------------------------
P0700 [0x0700]
Transmission control system, MIL request - circuit malfunction
Estatus: Confirmada
----------------------------
P07BF [0x07BF]
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) sensor A - circuit low
Estatus: Confirmada
----------------------------
P06DE [0x06DE] Archivo (inactivo)
Engine oil pressure control - control circuit malfunction, ON signal
Estatus: Permanente
----------------------------
P2097 [0x2097] Archivo (inactivo)
Post catalytic converter fuel trim (FT), bank 1 - too rich
Estatus: Permanente
----------------------------
P0658 [0x0658] Archivo (inactivo)
Actuator supply voltage - circuit low
Estatus: Permanente
----------------------------
P0967 [0x0967] Archivo (inactivo)
Pressure control (PC) solenoid B - circuit high
Estatus: Permanente
----------------------------
P0971 [0x0971] Archivo (inactivo)
Pressure control (PC) solenoid C - circuit high
Estatus: Permanente
----------------------------
P2721 [0x2721] Archivo (inactivo)
Transmission fluid pressure (TFP) solenoid D - circuit high
Estatus: Permanente
============================
Unidad de control del motorUnidad de control del motor
DTCs: 2
----------------------------
P0700 [0x0700]
Transmission control system, MIL request - circuit malfunction
General Electrical Failures [0x00]
Estatus: DTC supported by calibration, Current DTC, Test failed since DTC cleared, History DTC, Current DTC since power up
----------------------------
P07BF [0x07BF]
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) sensor A - circuit low
General Electrical Failures [0x00]
Estatus: GM failure record
============================
Unidad de control de la transmisión #2Unidad de control de la transmisión #2
DTCs: 1
----------------------------
P07BF [0x07BF]
Input shaft speed (ISS) sensor/turbine shaft speed (TSS) sensor A - circuit low
General Electrical Failures [0x00]
Estatus: DTC supported by calibration, Current DTC, Test failed since DTC cleared, History DTC, Current DTC since power up, Warning Indicator Requested
============================
BCMBCM
DTCs: 9
----------------------------
B1517 [0x9517]
Battery Voltage Below Threshold; Battery Voltage Above Threshold; Battery Voltage Plausibility Failure
General Electrical Failures: voltage below threshold [0x03]
Estatus: DTC supported by calibration, Test failed since DTC cleared, History DTC
----------------------------
B1529 [0x9529]
Control Module Voltage Reference Output 5 Circuit Low Voltage; Control Module Voltage Reference Output 5 Circuit High Voltage
General Electrical Failures: voltage below threshold [0x03]
Estatus: DTC supported by calibration, Test failed since DTC cleared, History DTC
----------------------------
B2955 [0xA955]
Security System Sensor Data CKT Malf
General Electrical Failures [0x00]
Estatus: DTC supported by calibration, Test failed since DTC cleared, History DTC
----------------------------
B3006 [0xB006]
Hood ajar circuit malfunction; Hood Ajar Circuit Short to Battery; Hood Ajar Circuit Short to Ground; Hood Ajar Circuit Open
General Electrical Failures: short to ground [0x02]
Estatus: DTC supported by calibration, Test failed since DTC cleared, History DTC
----------------------------
B3618 [0xB618]
General Electrical Failures [0x00]
Estatus: DTC supported by calibration, Test failed since DTC cleared, History DTC
----------------------------
C0277 [0x4277]
Brake Pedal Position Sensor Circuit Low Voltage/Open; Brake Pedal Position Sensor Circuit High Voltage; Brake Pedal Position Sensor Circuit Too Fast Transitions; Brake Pedal Position Sensor Circuit Calibration Not Learned
General Electrical Failures: short to ground or open [0x06]
Estatus: DTC supported by calibration, Test failed since DTC cleared, History DTC
----------------------------
C0890 [0x4890]
Device voltage reference output #3 circuit malfunction; Control Modul
Great video thank you! Question, would getting a BCM from a different 2014 Malibu need reprogramming?
Yes