Products that we use and recommend: ► OBD Scanner: amzn.to/4eJIKJA ► Brake Light Switch ( check fitment ): amzn.to/3Nuk23X ► Panel Removal Set: amzn.to/3YiMADu ►Torx Set: amzn.to/2hbyWgd ► Tool Set: amzn.to/3p5MM6t ► Screwdriver Set: amzn.to/3XRB28Q ► Engine Oil: amzn.to/3xBc8B9 ► Oil Filter: amzn.to/3w0Ulme ► Torque Wrench: amzn.to/32qyRwg ► Liqui Moly Engine Flush: amzn.to/3IiDBID ► OBD Scanner that we use most often: amzn.to/3I4MQfe ► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics
Try this....while you are driving and the cruise control will not engage...put your foot under the brake pedal and pull up as you attempt to engage the cruise control. If this works then your problem can be resolved in many cases by simply spraying WD-40 on the shaft that slides in an out of the brake switch. This removes the resistance/debris that builds up over time on the shaft and permits the shaft to slide freely thru the switch.
On a Buick LeSabre... If you push the 'Cruise Control' button and nothing happens (no amber light on in the on/off button) the easiest and therefore the FIRST thing to check is the #14 fuse in the fuse-box under the hood. If that is not the problem, the SECOND thing is check fuses under the steering column. (Under the steering wheel, about where your left knee is when driving). Remove the plastic cover panel (it just pulls off), then remove the steel plate that is under that panel (just four 10mm screws). There is a small black rectangular plastic box with wires sticking out of it. Open the box and you will find three 2 AMP fuses. Check these for a burn-out. They control the lights/function of the buttons on your steering wheel. AND they are not mentioned in the owners manual. This job takes about 10 minutes to do, and it will save you hours or even days of frustration. (I just fixed my own 2004 Buick Lesabre this way; and also fixed a friends 2001 Lesabre this way; so I'm guessing they all have these 2 amp fuses under the steering column).
Thanks guys. I had a problem with my nissan Dualis cruise control, when I turned it on the cruise light was on but the "Set" light would only flash and not allow it to engage. I cleaned the brake light switch and the clutch switch with WD40 which did not seem to make a difference, however I decided to see if there were any error codes that needed clearing and sure enough there was one, which after clearing it became operable again.
@@annettewolf7037 I cleared the code with the scanner, just prompted it to clear any errors. However, since doing that, the cruise is again not working! Could be an issue in the abs system.
@@bernardmiler3106 Hi, what code did you get? My Sienna 2005 has a check engine light on. The code says P0793, intermediate shaft speed sensor A circuit no signal. I wonder if it’s because I haven’t used Cruise Control in 4 years, and maybe some parts need cleaning?
Galera, Tenho um fit 09. Meu caso não era sensor do pedal de freio, mas sim, do pedal da embreagem. E o problema era o mais ridículo possível. Por isso quero compartilhar para quem tenha o mesmo problema (Talvez sirva o exemplo para outros carros), não caia na mão de mecânico pilantra. O "defeito" era o seguinte: O sensor tem um pino móvel central que entra e sai de acordo quando vc pisa no pedal. Quando não está pisando, o batente do braço do pedal pressiona esse pino, e envia um comando ao Cruise Control que pode ser acionado. Quando vc pisa no pedal, o pino sai, e envia um comando impedindo que o Cruise funcione. Quando fui verificar o sensor que fica lá embaixo no pedal , verifiquei que o batente onde deveria pressionar esse pino estava furado, pq caiu uma peça redonda que pressionava esse pino, então o q ocorria: independente de pisar ou não, tendo aquele furo, o pino NUNCA pressionava, portanto NUNCA enviava o comando de poder ativar o Cruise. Colei com bonder uma moeda de 5 centavos naquele furo, tapei o furo e voltou a funcionar. 😁😁😁😁
Why did you not just look at the brake light to see if goes on and off instead of using your meter? or is it a bit more complicated than just a simple on/off switch?
Hi dude great video, May i ask please, when i push the cruise button to set the speed. It just accelerates and does not stay at the Intended speed, what could that be?? Many thanks dude👊
For the brakelight switch? would your brakelights not just stay on forever? If your lights go out.. the switch works fine? Nothing else to check with electronics? Though?
My Toyota Avensis 2008 cruise control keeps on tripping. Sometimes it re engage when selecting again but then times you have to switch off everything and switch on again. There is not a exact patern that caused the cruise control to trip. Did you have a similar problem like this?
My Sienna 2005 has a check engine light on. The code says P0793, intermediate shaft speed sensor A circuit no signal. I wonder if it’s because I haven’t used Cruise Control in 4 years, and maybe some parts need cleaning?
I have a 2020 Volvo XC90. I had my brakes changed the other day and now the brake light stays on on my Dash, It also says parking brake service required, and my cruise control will not work
Hi there from Australia mate :) I'm here because, inexplicably, the cruise control on my MN Triton only works during the day?! I know, that must sound ridiculous, and yes I know it's got nothing to do with whether the sun is out or not lol, it has to be some sort of sensor I'm guessing. I'm only about 2 mins into the video so far and it looks very professional. If I'm lucky I'll find an answer here?! However..... The reason I am writing this is just to politely say, with all due respect, and I apologise in advance if I cause offence because I sincerely don't mean to, but omgggg I haven't counted but you must've said 'guys' about 100 times so far lol!! Although it's getting a little unnerving I can look past it, I just wonder if anyone else has picked up on that?!
How can i fix the cruise control in my 2013 kia optima? The cruise control light turns on, but that's it. The cruise doesn't activate. There are no service lights on. I'm clueless. Kia said it'll be $500+ to get it fixed and I'm tryna avoid. Please help me out.
The ride side of my steering wheel (cruise control settings) doesn’t work. No abs light. The left side of my steering wheel works (volume, mode, mute & Bluetooth buttons work)
I’m having the same problem on a Nissan Rogue. I went to the junk yard and replaced the cruise control switch but it stayed the same. I’m starting to suspect the clock spring may have something to do with it. Let me know if you find anything out.
@@my_flippin_journey A clockspring is a spiral-wound special rotary electrical connector which allows a vehicle's steering wheel to turn while still making an electrical connection between the steering wheel airbag and/or the vehicle's horn, cruise control, radio control, and other devices and the vehicle's electrical systems. The clockspring is located between the steering wheel and the steering column. Another term for this automotive part is a spiral cable. You can look up videos on TH-cam on how to replace the clockspring in your specific vehicle. That way you can see what it looks like and how to replace it. It’s not hard. Just delicate.
Any idea why my cruise control will come on when I hit the set button, it will hold the speed set at but for only about 20 to 30 seconds and then kicks off, I can hit resume and it will go back to the set speed, but only hold for 20 to 30 second again before kicking off, any ideas?
My problem on my 2001 Dodge Grand Caravan the Cruise Control is stuck on the on I can't turn it off the light stays on, on the dashboard how do I turn it off? And can I mess it up if I drive it like that?
Great video Man.. My brakes lights were not working, went to fix those but later found that after this my cruze control is not working at all.. Now i am goinh to show your video to that dum guy so we can fix it
I have a Renault Clio 3 sportsturer and the cruise control works only in the 3 first gears, when i shift up to 4 or 5th gear i cant apply the cruise controle, any idea what that could be?
ive got a 2011 dodge caliber. the cruise just shut off on its own going down the highway. it came back on but in the 3 days since, i cant set a speed on it. have you got any idea why it wont engage?
Erick mine is a 07 caliber, some times work and some times not, but when fail car is over 3000 rpm and replaced crankshaft position sensor and after clear code and check engine light up again works fine one day even w/ engine light on but next day is hard stared and rpm fail again and when that happens, cruise control not working. I have disconnected battery and works fine again, what can I do??
Okay so my cruise control does not work. I don’t have a bad brake light switch, the light comes on and off (can’t enable it) nor do I have any lights. I’ve also tore the steering wheel apart and all the wires look to be in good shape. I can’t figure it out for the life of me.
My cruise control and speed limiter stopped working after I fixed my injector fault and when the throttle body was recalibrated. The CC/SL was working when the car was misfiring but I only noticed it wasn't working right after the throttle was recalibrated. I'm not entirely sure when it stopped working, or what exactly caused it to stop. The buttons don't work and the dash lights are completely dead. I did have a check CC, Check SL message once and 1 fault code : consistent mulitplex signals for CC/SL. Any ideas on what could have caused it? It's a renault Megane mklll
Products that we use and recommend:
► OBD Scanner: amzn.to/4eJIKJA
► Brake Light Switch ( check fitment ): amzn.to/3Nuk23X
► Panel Removal Set: amzn.to/3YiMADu
►Torx Set: amzn.to/2hbyWgd
► Tool Set: amzn.to/3p5MM6t
► Screwdriver Set: amzn.to/3XRB28Q
► Engine Oil: amzn.to/3xBc8B9
► Oil Filter: amzn.to/3w0Ulme
► Torque Wrench: amzn.to/32qyRwg
► Liqui Moly Engine Flush: amzn.to/3IiDBID
► OBD Scanner that we use most often: amzn.to/3I4MQfe
► Check out our Amazon Store for the tools and parts that we use: www.amazon.com/shop/worldmechanics
Try this....while you are driving and the cruise control will not engage...put your foot under the brake pedal and pull up as you attempt to engage the cruise control. If this works then your problem can be resolved in many cases by simply spraying WD-40 on the shaft that slides in an out of the brake switch. This removes the resistance/debris that builds up over time on the shaft and permits the shaft to slide freely thru the switch.
Thank you for taking the time to comment this, you saved me time and money
@@kylethem9969 Glad to hear….the cruise control on my Silverado has been working fine for almost a year since the WD-40 treatment. Good luck!
Brilliant thanks for this it worked straight away 😁
Thank you so much !!!!!
Brilliant, logical and simple. Thanks
On a Buick LeSabre... If you push the 'Cruise Control' button and nothing happens (no amber light on in the on/off button) the easiest and therefore the FIRST thing to check is the #14 fuse in the fuse-box under the hood. If that is not the problem, the SECOND thing is check fuses under the steering column. (Under the steering wheel, about where your left knee is when driving). Remove the plastic cover panel (it just pulls off), then remove the steel plate that is under that panel (just four 10mm screws). There is a small black rectangular plastic box with wires sticking out of it. Open the box and you will find three 2 AMP fuses. Check these for a burn-out. They control the lights/function of the buttons on your steering wheel. AND they are not mentioned in the owners manual. This job takes about 10 minutes to do, and it will save you hours or even days of frustration. (I just fixed my own 2004 Buick Lesabre this way; and also fixed a friends 2001 Lesabre this way; so I'm guessing they all have these 2 amp fuses under the steering column).
i think you just saved my life, lol im going to check this out hopefully soon! mine just went out while i was driving out of no where!.
I know you have posted this a while ago, I'm just watching today! Thanks for wonderful info! 😊
If the brake light turns on when you stepon the pedal that means that switch is working yes?
Thank you very much for the information you save us a lot of money with your videos.
Thanks guys. I had a problem with my nissan Dualis cruise control, when I turned it on the cruise light was on but the "Set" light would only flash and not allow it to engage. I cleaned the brake light switch and the clutch switch with WD40 which did not seem to make a difference, however I decided to see if there were any error codes that needed clearing and sure enough there was one, which after clearing it became operable again.
How did you determine the code and how you clear the bad code?
@@annettewolf7037 I cleared the code with the scanner, just prompted it to clear any errors. However, since doing that, the cruise is again not working! Could be an issue in the abs system.
@@bernardmiler3106 Hi, what code did you get? My Sienna 2005 has a check engine light on. The code says P0793, intermediate shaft speed sensor A circuit no signal. I wonder if it’s because I haven’t used Cruise Control in 4 years, and maybe some parts need cleaning?
@@brighteyes6559 p0096. It turned out to be a faulty turbo charge temp sensor, a very easy and cheap fix.
@@bernardmiler3106 Great, good for you. 😃
Galera, Tenho um fit 09. Meu caso não era sensor do pedal de freio, mas sim, do pedal da embreagem. E o problema era o mais ridículo possível. Por isso quero compartilhar para quem tenha o mesmo problema (Talvez sirva o exemplo para outros carros), não caia na mão de mecânico pilantra.
O "defeito" era o seguinte:
O sensor tem um pino móvel central que entra e sai de acordo quando vc pisa no pedal. Quando não está pisando, o batente do braço do pedal pressiona esse pino, e envia um comando ao Cruise Control que pode ser acionado. Quando vc pisa no pedal, o pino sai, e envia um comando impedindo que o Cruise funcione.
Quando fui verificar o sensor que fica lá embaixo no pedal , verifiquei que o batente onde deveria pressionar esse pino estava furado, pq caiu uma peça redonda que pressionava esse pino, então o q ocorria: independente de pisar ou não, tendo aquele furo, o pino NUNCA pressionava, portanto NUNCA enviava o comando de poder ativar o Cruise. Colei com bonder uma moeda de 5 centavos naquele furo, tapei o furo e voltou a funcionar. 😁😁😁😁
Silly question, but why not just look to see if brake lights are working properly?
Real men learn the hard way lol. 💀
I need to know where the cruise control fuse is what type of fuse it is and how to replace thank you appreciate it very much. Have a good day.
Appreciate all the effort that you guys it into you videos thanks👍🏻
Why did you not just look at the brake light to see if goes on and off instead of using your meter? or is it a bit more complicated than just a simple on/off switch?
Thanks fixed my brake light switch
Hi dude great video,
May i ask please, when i push the cruise button to set the speed. It just accelerates and does not stay at the Intended speed, what could that be??
Many thanks dude👊
For the brakelight switch? would your brakelights not just stay on forever?
If your lights go out.. the switch works fine? Nothing else to check with electronics? Though?
In Soviet Russia, cruise control controls you.
great video bro
thanks for sharing how to troubleshoot cruise control switch, I'm having problem on my 2009 Dodge Grand Caravan. will do the diagnostics on it.
Did u figure it out yet. Appreciate it
My Toyota Avensis 2008 cruise control keeps on tripping. Sometimes it re engage when selecting again but then times you have to switch off everything and switch on again. There is not a exact patern that caused the cruise control to trip. Did you have a similar problem like this?
U should do a video on this about jetta tdi cars with surging cruise control. Countless posts on forums, and never any solutions.
Great info Max, will try to clean my abs sensors on a citroen tomorrow, this gave me a good troubleshooting startpoint,thanks
My Sienna 2005 has a check engine light on. The code says P0793, intermediate shaft speed sensor A circuit no signal. I wonder if it’s because I haven’t used Cruise Control in 4 years, and maybe some parts need cleaning?
I have a 2020 Volvo XC90. I had my brakes changed the other day and now the brake light stays on on my Dash, It also says parking brake service required, and my cruise control will not work
On most vehicles if your 3rd brake light is not working, it will not let cruise control activate. Especially GM vehicles.
Never considered a tire sensor is why my cc doesn't work ... *thanks*
Hi there from Australia mate :) I'm here because, inexplicably, the cruise control on my MN Triton only works during the day?! I know, that must sound ridiculous, and yes I know it's got nothing to do with whether the sun is out or not lol, it has to be some sort of sensor I'm guessing. I'm only about 2 mins into the video so far and it looks very professional. If I'm lucky I'll find an answer here?! However.....
The reason I am writing this is just to politely say, with all due respect, and I apologise in advance if I cause offence because I sincerely don't mean to, but omgggg I haven't counted but you must've said 'guys' about 100 times so far lol!! Although it's getting a little unnerving I can look past it, I just wonder if anyone else has picked up on that?!
So..when my third brake light lens broke and I pulled it off the connector it disabled my cruise control maybe?
Very professional video. Thanks for your help!
How can i fix the cruise control in my 2013 kia optima? The cruise control light turns on, but that's it. The cruise doesn't activate. There are no service lights on. I'm clueless. Kia said it'll be $500+ to get it fixed and I'm tryna avoid. Please help me out.
Helpful and informative video
Is this test happening while the car is on?
Break light fuse caused my trouble. Driver door fuse box 10amp
My favorite Muppet voice over guy!
On my 2008 Prius sometimes it works sometimes it doesn't what could that be a bad sensor?
Asking about 16 jeep grand Cherokee cruise control not working and wipers
Cruise control and wipers not working on 16 jeep grand Cherokee
Do you know why my cruise control and honk don’t work on 2008 Toyota Prius. And how I can fix it? Thanks
Probably faulty clock spring. May need to be replace.
My Toyota 1999 camry cruise control is acting erratically only on a slight down hill, why?
Hi, Can we also probe the brake light bulb wires to check if the switch is operating?
Not if there are multiple wires at switch.
The ride side of my steering wheel (cruise control settings) doesn’t work. No abs light.
The left side of my steering wheel works (volume, mode, mute & Bluetooth buttons work)
I’m having the same problem on a Nissan Rogue. I went to the junk yard and replaced the cruise control switch but it stayed the same. I’m starting to suspect the clock spring may have something to do with it. Let me know if you find anything out.
Just fixed mine. It was the clock spring. I just replaced it and the cruise control is now operating normally. Cost like $25 off of eBay.
@@Omardottcom *what is a clock spring* 🤔
@@my_flippin_journey A clockspring is a spiral-wound special rotary electrical connector which allows a vehicle's steering wheel to turn while still making an electrical connection between the steering wheel airbag and/or the vehicle's horn, cruise control, radio control, and other devices and the vehicle's electrical systems. The clockspring is located between the steering wheel and the steering column. Another term for this automotive part is a spiral cable.
You can look up videos on TH-cam on how to replace the clockspring in your specific vehicle. That way you can see what it looks like and how to replace it. It’s not hard. Just delicate.
Any idea why my cruise control will come on when I hit the set button, it will hold the speed set at but for only about 20 to 30 seconds and then kicks off, I can hit resume and it will go back to the set speed, but only hold for 20 to 30 second again before kicking off, any ideas?
Do you work on subaru?
My is the switch on my steering wheel 07 pathfinder almost 200 thousand miles
My problem on my 2001 Dodge Grand Caravan the Cruise Control is stuck on the on I can't turn it off the light stays on, on the dashboard how do I turn it off? And can I mess it up if I drive it like that?
I have an 09 Mitsubishi Lancer GTS the control light turns on for cruise at does not engage
If you change the incorrect size of tire; This is the reason on Mercedes SLK
Mine wasn't working pulled the fuse, fuze was good put it back still nothing, pulled fuse again scrapped the leads put it back in and it works
Your kick ass 😎😎😎😎😎😎😎😎😎 thanks so much .. me and my husband have got so much great info in all your videos
I have a 2000 Chevy Silverado z71, speedometers reads 5 miles over, can it be the problem of my cruise control not working.
Great video Man..
My brakes lights were not working, went to fix those but later found that after this my cruze control is not working at all..
Now i am goinh to show your video to that dum guy so we can fix it
Very helpful 👍
I have a Renault Clio 3 sportsturer and the cruise control works only in the 3 first gears, when i shift up to 4 or 5th gear i cant apply the cruise controle, any idea what that could be?
ive got a 2011 dodge caliber. the cruise just shut off on its own going down the highway. it came back on but in the 3 days since, i cant set a speed on it. have you got any idea why it wont engage?
Erick mine is a 07 caliber, some times work and some times not, but when fail car is over 3000 rpm
and replaced crankshaft position sensor and after clear code and check engine light up again works fine one day even w/ engine light on but next day is hard stared and rpm fail again and when that happens, cruise control not working. I have disconnected battery and works fine again, what can I do??
Most of this video is just him using a device most people don't have lmao
anyone know where i can find a wire diagram for a 2013 accent. just for the cruise control system.
I have a 2008 Mercedes ml350 the cruise control is stuck how do I fix it
Okay so my cruise control does not work. I don’t have a bad brake light switch, the light comes on and off (can’t enable it) nor do I have any lights. I’ve also tore the steering wheel apart and all the wires look to be in good shape. I can’t figure it out for the life of me.
We’re you able to figure out the problem?
Great video! Just curious, where is your accent from?
Russia 🇷🇺 he the "CRAZY RUSSIAN HACKER'S COUSIN!
His accent is from his mouth.
I think he's dutch.
My cruise control quit working as i was driving and wouldn't come back on.
New brake switch installed....cruise control light is on...no abs lights on dash...this video is useless to me....
I have an notice that says check stop lamp
Is a stop lamp a break light on a fiat?
I hate videos with accents I can barely understand
Sounds fake
Ok
I'll rush right out and buy a scanner. 🤨
It would save you a lot more than it costs!
Uh...what was that last part?
My cruise control and speed limiter stopped working after I fixed my injector fault and when the throttle body was recalibrated. The CC/SL was working when the car was misfiring but I only noticed it wasn't working right after the throttle was recalibrated. I'm not entirely sure when it stopped working, or what exactly caused it to stop. The buttons don't work and the dash lights are completely dead.
I did have a check CC, Check SL message once and 1 fault code : consistent mulitplex signals for CC/SL.
Any ideas on what could have caused it? It's a renault Megane mklll
Not enough MIDROLL ads
😂
Guys, good guys video guys but guys too guys many guys guys.
Please stop saying 'guyz'..!! Hahaha
Евала, пичове!
2:35
My 2015 calorado is losing power an rev counter goes up down but still doing 100km..surging like no desil or air.
you talk way too fast
what a bull of crap..
I don’t understand shit this guy is saying
Very hard to understand his English.
🤷🏾♂️ What?? I don’t know what your talking about, I understood everything he said.