How to Program a new Nice Transmitter using another programmed Nice Transmitter
ฝัง
- เผยแพร่เมื่อ 22 ส.ค. 2024
- Program an Inti transmitter remote for your Nice or Apollo gate opener in seconds. Looking to program a Nice transmitter to a plug-in receiver- view • How to Program a Nice ...
- วิทยาศาสตร์และเทคโนโลยี
For all for whom this doesn't work. Try this solution: place both transmitters next to them (not like in this video, just next to them). On new transmitter, press button you want to map and hold for around 8 seconds, then release it. Now old transmitter press the same button three times each time for around 1 second. After that, press once the same button on new transmitter also for around 1 second. From now on button should be mapped to new transmitter. You have to do the same operation for other buttons as well as this doesn't copy whole transmitter but only button you press.
Thank you. It worrked for me. Just put them next to each other.
Worked for me back to back rather than top to top but button presses worked as per your video thank you! Mine are Nice ON2E transmitters.
Press and hold button on new transmitter for 6 seconds. Then press button 3 times on old transmitter. Then press button on new transmitter ones. Now its programmed. Always works
Good
4444
Do you have to hold them close like the video?
This didn't work for me either
The above method didn't work. your method worked for me. Thanks!
I was not able to program a new transmitter following this video for an older version of the transmitter with the new model transmitter. But I followed the programing procedure for older Nice motors and I was able to program the unit with the following steps: You need to make sure you are close to the receiving unit (motor)
• Procedure with OLD transmitter memorized in Mode 1:
01. Draw near the control unit with the two transmitters: Wait 1 second between one step and the next.
02. On the NEW transmitter press and hold any key for at least 8 seconds then release it.
03. On the OLD transmitter press and hold any key to be copied for at least 2 seconds then release it.
04. On the OLD transmitter press and hold any key to be copied for at least 2 seconds then release it.
05. On the OLD transmitter press and hold any key to be copied for at least 2 seconds then release it.
06. On the NEW transmitter press and hold a key to be memorized for at least 5 seconds then release it.
Repeat the procedure for each transmitter to be memorized
Steps 3&4 are identical.. I dont think this is correct. Also I tried it and it did not work
Worked perfectly for me thank you
After that, you'll need to wait for 10 seconds, and it works.
@@aaronstately it is correct, you need to press the button 3 times at this point, that's why steps 3. - 5. are identical
Hey thanks buddy. I failed with the Nice instructions both on the booklet & this video.... then saw your post and that's worked perfectly! 👍
If this doesn't work, do the following: on the new remote, hold down the button you want to program for 8s, after that press the button on the old remote three times (about 1s per click), then press the same button on the new remote again for one last time. Wait 5s and the remote should work. I was standing right next to my gate, not sure if that is required. I had an ERA1 transmitter already programmed and used it to program an ERA2 transmitter.
Worked great on my Nice remote. Thanks for the video!
You need to make sure the battey in the donor transmitter is new/good. I tried several times without success but changed the donor battey and worked first time.
Man I have the same exact models, & I can’t get my new remote to work. I didn’t think about the battery. I hope that’s what’s wrong with mine, because I’ve wasted hours upon hours trying to program these dam remotes.
I have tried to program a Nice Era 2 as a new device against Nice Era 1, and it doesnt work
Hello Do they have to be the exact same? For example I have a 4 bottom Nice can I copy to a 2 button Nice?
Does not always work. There is another way
Hi. How do you reset a remote. I have two new ones that just will not communicate. I’ve pressed the remotes 10 times as per your instructions but that’s not working either. Please can you help.
I am always getting the error flashes on the OLD remote, 6 flashes then 10,
Hello. It’s the same for Nice Flo2Re? With a Nice OX2 receiver?
Is there a way to make Nice devices to work with US HomeLink?
Great the instructions that you gave didn't work so now what
Hello- our tech support team is available to help you. You can reach them by phone or text at 253-201-2918.
@@texasredstotaloutdoors9818 hey how did you get it to work?
Yeah.. total BS. Doesn’t work. So I paid €25 for a gate fob saving €45, as the gate company wanted €70.
Now they still want €70 as a call out to come and program this one!!!