Big Thankyou from Houston Texas!!! Hurricane Beryl wiped out the power and we couldn’t get our generator started. Followed what you did step by step and now we have our refrigerator and AC unit going. 🎉
It’s smart to have a extra new carb , fuel hose and filter plus a tank cut off valve along with 8/12 gts of oil Usually the air filter lasts for years but still might as well get one 😮
This video was exactly what I needed. My generator was sitting with gas in it for a couple years. I had to clean the tank and gas valve but this tutorial on the carburetor was what started her right up. Thank you!
Thank you for the tutorial. This worked like a charm for me. Once I pulled out the carburetor, it was exactly like yours. Could not see through the jets. I did buy an ultrasonic cleaner, but had to run sewing bobby pins through the jet to clear it out. Once reassembled, it took only one pull to start it. I decided to let then entire tank a fuel run through it rather than stopping the engine and letting old fuel gum up the carb again.
Thank you for this video. Was having a carb issue most likely from the ethanol in the gas I was using. This video helped me take the carb apart and clean it so I could get this generator running again. Appreciate all the visuals and the time you take explaining. Great video. And also thank you for your service and sacrifices
Your Video was a life saver! Had a power outage and I went to use my Predator 6500 and it would not start. Got online , found your channel and bam, works like new! Took me all of 45 min. Thank ya much!
Excellent video. Pulled my generator out preparing for Hurricane Helena. I didn't work. Found your video and followed your steps. Got it running great. Now crossing my fingers hoping I won't need it. Thanks for the video
I have its big brother the 7,000/8750 Predator I purchased in 2016. It is always nice seeing Predator troubleshooting/repair videos on TH-cam. I've been pretty careful running ours dry and shutting off the fuel valve after I do the typical 3-month testing cycle. So far so good.
I'm really glad to hear that you maintain your generator. It's always wonderful to hear of someone who shares similar techniques and values when it comes to upkeep. Thank you for sharing your knowledge and experiences!
Another issue that seems to plague these predator gensets is a partially clogged combination fuel tank shut off valve/filter on the bottom of the tank . They will often start, but not stay running or will run only with the choke on. Also, they may run fine at idle, but when any load is applied, will stumble and die due to insufficient fuel flow.
My carburetor was badly corroded so I replaced it. Actually twice. All jets are clear and clean , properly installed. The replacement carb has a mixture scew where the original had a plug. The machine fires well on brake cleaner but refuses to run on gas. Gas is fresh 91 octane pure gasoline. I replaced the fuel tank, cut-off, added a fuel filter, lines and carb. What can my problem be ? I have set the mixture screw open 1-1/2 turns and varied it up to 3 turns with no results. This one has me baffled. Help if you can. Thanks
LOL, Sometimes it's easy to fix for some people. while sometimes it's easier for others to fix it. Knowing one's extent for repairing it themselves is a key part. I hope you'll get it back up and running either way. Cheers!
I have a brand new carb, new tank, new battery, new plug, still wont start, thing is the generator ran for fifteen munutes when I got it brand new, so I didn't use it for seven years, just sat in the garage until now, everything is new what should I do, thank you...
Just found your channel. This video is what I was looking for. I have the 9000 version that I have left sitting for 1yr. If people can't understand that that some people need to use ai voice to communicate sorry for them. You adapt and over come obstacles put in your path. Add one more subscriber to your list. 👍👍👍👍
Im starting to work on my sister's 6500 got spark pretty sure its the fuel but it gas an electric part at the bottom of the bowl so I think I need to test that first, do you know how I do that?
There is a spring on the accelerator rod that is un hooked. It was when you started working on it. It keeps the rod from falling out of it;s hole. If you look close at the engine side of the rod. it is flopping there. I had to do my carb about a week ago. That is why I spotted it.
Thank you for the video was very informative. My problem is I could get the carburetor off if I took it apart I wouldn't be able to go back together again.... LOL
What is a good budget friendly ultrasonic cleaner and solution to buy/user? I'm running into the same issue, and would like to repeat this tutorial, but I do not own an ultrasonic cleaner
I truly appreciate your understanding. It means a lot to me. It can be disheartening to receive comments focused solely on the use of an AI voice in my videos, especially when they don't offer constructive feedback on other aspects. So, I want to express my gratitude for your acknowledgment and support. Thank you for recognizing the effort and content beyond just the voice. Your understanding is truly valued.
Man I have a predator generator 6500 amp 301 thats not starting I'm thinking I need to do this with the carborator I've had it for about 4 years it's been there for me through the freeze and hurricane beryl. It stopped working right after the storm.where can I get the cleaning solution for soaking the carborator?
Big Thankyou from Houston Texas!!! Hurricane Beryl wiped out the power and we couldn’t get our generator started.
Followed what you did step by step and now we have our refrigerator and AC unit going. 🎉
It’s smart to have a extra new carb , fuel hose and filter plus a tank cut off valve along with 8/12 gts of oil
Usually the air filter lasts for years but still might as well get one 😮
This video was exactly what I needed. My generator was sitting with gas in it for a couple years. I had to clean the tank and gas valve but this tutorial on the carburetor was what started her right up. Thank you!
Thank you for the tutorial. This worked like a charm for me.
Once I pulled out the carburetor, it was exactly like yours. Could not see through the jets. I did buy an ultrasonic cleaner, but had to run sewing bobby pins through the jet to clear it out.
Once reassembled, it took only one pull to start it. I decided to let then entire tank a fuel run through it rather than stopping the engine and letting old fuel gum up the carb again.
Thank you for this video. Was having a carb issue most likely from the ethanol in the gas I was using. This video helped me take the carb apart and clean it so I could get this generator running again. Appreciate all the visuals and the time you take explaining. Great video. And also thank you for your service and sacrifices
Your Video was a life saver! Had a power outage and I went to use my Predator 6500 and it would not start. Got online , found your channel and bam, works like new! Took me all of 45 min. Thank ya much!
Excellent video. Pulled my generator out preparing for Hurricane Helena. I didn't work. Found your video and followed your steps. Got it running great. Now crossing my fingers hoping I won't need it. Thanks for the video
I have its big brother the 7,000/8750 Predator I purchased in 2016. It is always nice seeing Predator troubleshooting/repair videos on TH-cam. I've been pretty careful running ours dry and shutting off the fuel valve after I do the typical 3-month testing cycle. So far so good.
I'm really glad to hear that you maintain your generator. It's always wonderful to hear of someone who shares similar techniques and values when it comes to upkeep. Thank you for sharing your knowledge and experiences!
Just fixed my generator cause of you! Thank ypu so much! Hurricane milton on his way to me
Another issue that seems to plague these predator gensets is a partially clogged combination fuel tank shut off valve/filter on the bottom of the tank . They will often start, but not stay running or will run only with the choke on.
Also, they may run fine at idle, but when any load is applied, will stumble and die due to insufficient fuel flow.
great video...what liquid can i use to clean carb...?
...this is exactly what I need to do to my Predator 4000....your video will be of great help....thanks for posting... 🙂
My carburetor was badly corroded so I replaced it. Actually twice. All jets are clear and clean , properly installed. The replacement carb has a mixture scew where the original had a plug. The machine fires well on brake cleaner but refuses to run on gas. Gas is fresh 91 octane pure gasoline. I replaced the fuel tank, cut-off, added a fuel filter, lines and carb. What can my problem be ? I have set the mixture screw open 1-1/2 turns and varied it up to 3 turns with no results. This one has me baffled.
Help if you can. Thanks
Great video! What chemical agent did you use in your Ultrasonic Cleaner please?
As soon as you said "let's take it apart" I said to myself "let's call a professional" 😅
LOL, Sometimes it's easy to fix for some people. while sometimes it's easier for others to fix it. Knowing one's extent for repairing it themselves is a key part. I hope you'll get it back up and running either way. Cheers!
I have a brand new carb, new tank, new battery, new plug, still wont start, thing is the generator ran for fifteen munutes when I got it brand new, so I didn't use it for seven years, just sat in the garage until now, everything is new what should I do, thank you...
Just found your channel. This video is what I was looking for. I have the 9000 version that I have left sitting for 1yr. If people can't understand that that some people need to use ai voice to communicate sorry for them. You adapt and over come obstacles put in your path. Add one more subscriber to your list. 👍👍👍👍
Thank you so much for the comment! Let me know if you get it back up and running.
Got home and it took 40 minutes to clean the carburetor and the generator is running perfect. 👍👍👍👍🙏🙏🙏🙏@TheSmallEngineMechanic
Outstanding video! I love your step by step methods of troubleshooting. New subscriber here, keep up the great work:)
Im starting to work on my sister's 6500 got spark pretty sure its the fuel but it gas an electric part at the bottom of the bowl so I think I need to test that first, do you know how I do that?
Found a neglected generator took it apart wondering how to put throttle return spring back i noticed it was completely off both ends
There is a spring on the accelerator rod that is un hooked. It was when you started working on it. It keeps the rod from falling out of it;s hole. If you look close at the engine side of the rod. it is flopping there. I had to do my carb about a week ago. That is why I spotted it.
Thank you for the video was very informative. My problem is I could get the carburetor off if I took it apart I wouldn't be able to go back together again.... LOL
what can you suggest for overload light on when nothing is connected to the generator
The engain is jumping so what can I do
What is a good budget friendly ultrasonic cleaner and solution to buy/user? I'm running into the same issue, and would like to repeat this tutorial, but I do not own an ultrasonic cleaner
Personally, as I'm hearing impaired and must use headphones I find the "voice" very easy to understand.
I truly appreciate your understanding. It means a lot to me. It can be disheartening to receive comments focused solely on the use of an AI voice in my videos, especially when they don't offer constructive feedback on other aspects. So, I want to express my gratitude for your acknowledgment and support. Thank you for recognizing the effort and content beyond just the voice. Your understanding is truly valued.
So its dust in the carburator?
Thank you!
Very well done. Thank you!
🖖😎👍
Thank you brother this is a life saver
Man I have a predator generator 6500 amp 301 thats not starting I'm thinking I need to do this with the carborator I've had it for about 4 years it's been there for me through the freeze and hurricane beryl. It stopped working right after the storm.where can I get the cleaning solution for soaking the carborator?
Get carb acid but it’s costly or use can carb spray 😮
If you have a sonic cleaner dawn dish soap works well and it’s what we use in our shop 😮
Remove carb... Find 10mm socket... Failed
Thanks Brotha 👌🏻
Thanks man it worked ...yall just get yalls fingers dirty and it will fire up correctly