Might have been better when aligning the 3 disks to use DTI on tack weld then position them before final weld! I do love these videos watching how someone gets over a problem with ingenuity.
I too wish to build a pellet machine and small hammer mill .. but I dont have a lathe and am not confident enough in my fabrication skill to build a machine that slings blades at 1700 rpm 😆 maybe one day. I do enjoy watching yours, though. Thanks so much for sharing!
A lathe is very useful for a household. I have never built a grinding mill either. I wanted to try and I see that I succeeded. Thank you for your support.
Супер , молодец!! Я изготовил дробилку такого же плана,-молотковую дробит зерновые,сено,початки кукурузы,на вал установил вентилятор и дробленная масса уходит в мешок через цыклон. Заходите в гости имею дробилки разных конструкций, экструдеры,веялка зерновых,пресс для брикетов, чертежи..и другие поделки..
I have one almost same, but with square blades. I switch side of blades because side that hits become rounded. So, side that hits is square again but I can see that parts of wood that comes out are a bit bigger than before. At start it was like in your video at 1st seconds of video. What can be a reason for that?
@@DorelBorlea merci , asha fac shi eu dar se mananca diuzele prea repede. Am cumparat un pistol cu masa incorporarata dar nu am apucat sal probez. Salutari din Spania
@@igotbricotools2035 la materiale pana in 6mm grosime duzele merg foarte bine. Am taiat aproximativ 3 metri de tabla.de 6 mm cu o singura duza si inaca mai merge.
Might have been better when aligning the 3 disks to use DTI on tack weld then position them before final weld! I do love these videos watching how someone gets over a problem with ingenuity.
I too wish to build a pellet machine and small hammer mill .. but I dont have a lathe and am not confident enough in my fabrication skill to build a machine that slings blades at 1700 rpm 😆 maybe one day. I do enjoy watching yours, though. Thanks so much for sharing!
A lathe is very useful for a household. I have never built a grinding mill either. I wanted to try and I see that I succeeded. Thank you for your support.
Супер , молодец!!
Я изготовил дробилку такого же плана,-молотковую дробит зерновые,сено,початки кукурузы,на вал установил вентилятор и дробленная масса уходит в мешок через цыклон.
Заходите в гости имею дробилки разных конструкций, экструдеры,веялка зерновых,пресс для брикетов, чертежи..и другие поделки..
Nc project, can i ask what is the size of those nuts? and also the thickness of the plates?
Thanks. The plates are 6mm thick, the nuts are 16mm but I drilled them with a 19mm drill.
I want the mill, my wife wants the dog!
Is it possible to make a hammer mill from an old dust blower fan? Must the "hammers" be movable or can i weld them directly to the fan blades?
I think you can build a straw grinding mill out of a dust fan. The hammer mill is built with movable knives.
@@DorelBorlea I want to grind wood chips into smaller particles like sawdust so i can use it in my pellet press
I ground wood chips with this hammer mill. It's going super well.
@@DorelBorlea Can you grind wood chips with a mill with fixed knifes?
@@theodorranebo2909 I don't know.
Hello sir, can it cut coconut husk?
Hello. I don't know.
Good work?
But Mill for which material ?
straw, grass, alfalfa
I have one almost same, but with square blades. I switch side of blades because side that hits become rounded. So, side that hits is square again but I can see that parts of wood that comes out are a bit bigger than before. At start it was like in your video at 1st seconds of video. What can be a reason for that?
The type of wood and the humidity of the sawdust. The mill should grind the same, only the sawdust is different.
Sir could u please suggest this type hammer mill grind the waste printed circuit boards in to powder
Nice video
Good work
Thanks!
Mai montezi inca doua axuri cu cutite s-au ramane in doua?
4 axuri cu cutite am vrut sa montez dar merge bine si cu doua.
I wonder why you not cut the hair around the Dog eyes?
Bun vídeo 👍
0:37 cand tai cu plasma la ce distantza tzii diuza de placa?
O tin lipita de material
@@DorelBorlea merci , asha fac shi eu dar se mananca diuzele prea repede. Am cumparat un pistol cu masa incorporarata dar nu am apucat sal probez.
Salutari din Spania
@@igotbricotools2035 la materiale pana in 6mm grosime duzele merg foarte bine. Am taiat aproximativ 3 metri de tabla.de 6 mm cu o singura duza si inaca mai merge.
How much does it cost
Is not for sale.
Berapa harga satu unit pak
Ok bien
what size are those blades sir?
96mm × 40mm x 3mm
thank you very much! how about the plates and steel rods?@@DorelBorlea
@@denjaspersilorio7621 plates are 230mm , steel roads are 19 mm.
Moter HP?
5kw
@@DorelBorlea production per hour
@@user-dl7ip9mt6e I don't know
❤🎉❤🎉