Oh snap! I only just finished saying how I couldn’t figure out a pedestrian gate with an auto gate…and you’ve only gone & solved it. You’re a freaking genius as well as an artist & skilled tradesman. Impressive stuff.
I'm love this. Do you have a video that shows you how to put the runner across the bottom so the slide the hardware the gate slides on I'm trying to do this to my backyard so I can park my van inside.
Please complete by flashing off the gap between the access gate and the main gate, using 30x3 galv flat bar and tack weld or tek screw for privacy. Gorgeous job mate 👍
Very nice,.. I’d be interested in knowing how the steel weathers at the joints over time where you had to clean up the welds and the galv will be missing?
I love it. But a question for you: why not build a pedestrian gate in the static section of the fence beyond the mailbox? Then the gate could open all the way right to the ground, rather than have 15cm of timber horizontally above the ground to step over.
I like it a lot. How much does something like this cost? Also if the driveway would be fixed up or redone in the future, would it be necessary to do that first before a gate like this?
Great man! Wish it was out of hardwood battens your attention to detail would be showcased by being even prettier. Did you pour a concrete pad underneath the brickwork in the driveway?
Hey Jason, do you have any advice what screws or anchors to use to install the v-track into asphalt? I would like to do it right the 1st time and not have them come loose down the road. Thanks!
The thumbs down votes are not thinking correctly this was beautiful work .... this was a great inspirational video. How did you do the pyramids on the posts? I instantly sub thanks for the video
Thanks Ryan. I appreciate that. The pyramids are done by squaring a line around the post, then using a 9 1/4 circular saw upside down and following the line on all 4 sides.
what if the gate got stuck open or someone left it open then would it get damage from the gate opener. then u have a step over the the gate when getting in and out. what if u have to drag a trash can then u'd have to carry it over? And u have to duck to go in and out
Why would you bother? In order for you to enter the gate it needs to be unlocked. Isn’t that the whole point to the sliding gate to have security. It only costs a couple dollars to get an automatic gate jigger to give to your whole family. Just open the gate a meter and then close it
The pedestrian gate needs a dead man on to stop the gate operating when in the open position, again you must start to install safety edges due to the resent fatalities.
Looks great but in the USA it’s against national building code. The pedestrian gate must be always from the vehicle gate. Several people have been killed because of designs like this. Although I love it! Ul325 & ASTM F2200 documents clearly say this can’t be done
Oh snap! I only just finished saying how I couldn’t figure out a pedestrian gate with an auto gate…and you’ve only gone & solved it. You’re a freaking genius as well as an artist & skilled tradesman. Impressive stuff.
Bravo just getting started this is clean work man thanks for sharing
Much appreciated 😁
That is a very smooth transition. Love the idea of the walk gate on the rolling gate.
ProfessorRiper thanks. It’s pretty cool
I'm love this. Do you have a video that shows you how to put the runner across the bottom so the slide the hardware the gate slides on I'm trying to do this to my backyard so I can park my van inside.
Please complete by flashing off the gap between the access gate and the main gate, using 30x3 galv flat bar and tack weld or tek screw for privacy. Gorgeous job mate 👍
Oww, The nicest one so far on you tube. I am doing one now for me just like your prototype.
That’s awesome. All the best with your project
Nice job and good result 👍
Thank you
Outstanding job, very nice.
Thank you. Very kind
Nice smooth operation. Very clean work, Nicely Done!!
Bill Baggins thank you very much. Glad you like it
So beautiful!!! ❤
Thanks 😊
This is excellent work
That’s awesome and beautiful! Love it! Want it!! How much would something like this cost?
Thanks heaps. I don’t discuss price online sorry.
What sliding rail system did you use?
Jason what motor do you use on your sliding gates?
Very nice,.. I’d be interested in knowing how the steel weathers at the joints over time where you had to clean up the welds and the galv will be missing?
Wow,..sweet set up,..only one on the block I bet,..very unique,..is it solar power or was that an extension cord I seen?
Awesome really great work we’re you located
Thanks. You can check out my service areas on my website 😊
Man I really wish to know how to do this from start to finish
I love it. But a question for you: why not build a pedestrian gate in the static section of the fence beyond the mailbox? Then the gate could open all the way right to the ground, rather than have 15cm of timber horizontally above the ground to step over.
Simple answer. Not what the client wanted 👍
That's bad ass. Great Job
Lol. Thank you. I think so too
Nailed It!😎
Thanks heaps 😊
This is awesome
NICELY DONE,,, where are the pLans ???
I like it a lot. How much does something like this cost? Also if the driveway would be fixed up or redone in the future, would it be necessary to do that first before a gate like this?
that PA gate in the slider in a great idea
When there isn’t really other options, it is a great alternative 😁
Love it!!! Mines next 😂😂
🥰🥰
How much ? For this fence
What a great fence! Good on ya mate!
Justin Tackett thanks mate
Good idea... Australia I presume?
@naileditfencing:
Vey nice end product! like to build similar w/ no motor and with wood framing.would you recommend? All replies welcomed. Thanks!!
Thank you. Wood frame for the fence is fine but not for the gate
What make and model of motor is that?
Powertech 500
Can you make a gate for me like this .
Depends if you are in my service area. Check out my website. 👍
that's badass!
Thanks 😊
Great man! Wish it was out of hardwood battens your attention to detail would be showcased by being even prettier.
Did you pour a concrete pad underneath the brickwork in the driveway?
Yeah I agree but I’ll bet after buying the concrete work, motor and gate install they really liked the look of treated pine.
Hey Jason, do you have any advice what screws or anchors to use to install the v-track into asphalt? I would like to do it right the 1st time and not have them come loose down the road. Thanks!
6mm galvanised dino bolts should do the trick.
The thumbs down votes are not thinking correctly this was beautiful work .... this was a great inspirational video. How did you do the pyramids on the posts?
I instantly sub thanks for the video
Thanks Ryan. I appreciate that.
The pyramids are done by squaring a line around the post, then using a 9 1/4 circular saw upside down and following the line on all 4 sides.
How much in materials?
Are you in South Florida?
I’m a little more south than that. Melbourne Australia 😂😂
🔥🔥🔥👍
what if the gate got stuck open or someone left it open then would it get damage from the gate opener. then u have a step over the the gate when getting in and out. what if u have to drag a trash can then u'd have to carry it over? And u have to duck to go in and out
The pedestrian gate has an automatic hinge so it won’t get stuck open. If you want to take your wheelie bin out, open the sliding gate.
Hi there I really want one like this installed at my home can I get more information?
Rodrigo AP what sort of information?
Cold gal will rust thru. HDG is a superior option. Treated pine will bow. Look good for a year or 2.
Yeah nah mate. 😂🤦♂️
If USA and near by, I would ask your price for a fence here....
I hear that all the time. I appreciate that. I’d love to move to the US.
Why would you bother? In order for you to enter the gate it needs to be unlocked. Isn’t that the whole point to the sliding gate to have security. It only costs a couple dollars to get an automatic gate jigger to give to your whole family. Just open the gate a meter and then close it
I agree with you. But, what the client wants, the client gets 👍
Genius mate. Looks very Aussie work standard to me.
Bluegem Videos thanks mate. I appreciate it. 😃
its a sliding gate!
The pedestrian gate needs a dead man on to stop the gate operating when in the open position, again you must start to install safety edges due to the resent fatalities.
Good way to diss the neighbors that aren't weLcome,,, hehe🧐LoL
Frame needs a coat of paint
JP a lot of people prefer the gal steel look
Looks great but in the USA it’s against national building code. The pedestrian gate must be always from the vehicle gate. Several people have been killed because of designs like this. Although I love it!
Ul325 & ASTM F2200 documents clearly say this can’t be done
Thanks for the heads up. Should have added it to the constitution. 😂
Oh I thought that handle was a glory hole. Is that an optional extra?
Anything can be done for a price. 😂
Could have installed the letterbox in the gate, just make it bigger and flatter.
Janette Francis I could have. Alternatively, I could install it where the customer preferred it. Like I did. 😉
@@naileditfencing Good for you.
Janette Francis good for the client. They got what they asked for. 👍