Wrapping and installing the 77 C10s custom console
ฝัง
- เผยแพร่เมื่อ 22 ก.พ. 2023
- Part 1 of the console build
• Building a custom cons...
Black Suede
www.ebay.com/itm/172176910248...
Black leather
www.ebay.com/itm/363806710490...
3m super 90
(Used 3 cans)
3M Hi-Strength Spray Adhesive 90, 14.6 oz. a.co/d/fy2hKhn
L brackets
16 Pcs L Bracket Stainless Steel... www.amazon.com/dp/B0B2LG2XXZ?...
I'd say stop overthinking and doubting yourself. You got the skills
Glad to see the power probe being useful to you. You and your dad are doing a great job!
Thank you!
Awesome build!
Looks killer! Nice work.
Looks good. Nice job.
awesome job mate looks great
The best way to apply fabrics with contact adhesive is to place the fabric on top of where its to be installed, being sure to allow around 10-15% extra around all edges then to apply the glue simply fold the material in half with it remaining in it's install location, revealing half the surface to be be glued as well as half the material to be glued. If you're worried of any overspray getting on the face, newspaper works well to quickly mask spots off. Now once the glue has tacked, just need to flip the folded fabric back over into the glue, rubbing it out along the way, removing any wrinkles to the edges. Then fold the other half back, and apply the glue again.
Once the entire surface is glued and fabric is in place, you can flip the board face down, spray the edges, and once ready using the extra material that was allowed to run past the edges you can stretch the fabric around the edges, and once everything is good use a razor to trim the excess off .
Just watched the video and you are a rockstar brother ! I see the tubing you used on the air vents and man that is such a great idea
Thanks man!!
@@kesselsgarage what's the idea? Isn't that the normal flex tubing that runs to the vents?
Gotta say u did a fantastic job for your first time . I'm laughing at you saying its heavy mine I'm building one now that's 3\4" almost a whole sheet with 6 speakers and a sub and 40000 watt amp and breakers wires fuse books it takes two guys to even move it still great job bro love the truck I would love to have 1 some day
😂 yeah you make mine look like a paperweight. Sounds like your going to be slamming! Thanks man!
I put power and ground fused distribution block on the support under the radio
I need one like that..Nice
looks great! I'm going to try to build one for my 85 with a bench seat. Couple of questions though, how deep are those cup holders and what size speakers did you use? Thank you
Thank you!! I don’t have an exact measurement but they will hold a large yeti cup. Here is the link www.basspro.com/shop/en/tigress-stainless-steel-cup-insert. The speakers are 6.5” and the buttons are 3/4” buttons from billet automotive buttons.
I was thinking I'd use some thin foam between my board and vinyl.
Thanks!! Yeah if I was going to do it again I think I may put it around the areas where you would lean against
What size button switches did you use?
How tall is it from the floor to the top of the storage compartment?
Hey buddy looks great where did you get your cup holders from
Thanks! They are actually boat cup holders but they are the only big ones that would hold a yeti cup. Here’s a link to them
www.basspro.com/shop/en/tigress-stainless-steel-cup-insert
What size chamfer router bit did you use? Thanks
It was a 1/2”
Where did you get your seats. Or what are they out of.
They are new cipher bucket seats.
What is the price for that Center consolé for a 06 single cab Chevy
Sorry man as of right now I don’t sell them
Where did you get the exhaust cutoff bottons?
They are from Billet Automotive buttons
How wide is it?
How is it all attached?
(After the pieces were wrapped)
All of the side pieces and braces are attached with L brackets. The radio bezel and cup holders are just placed in and they are held down by the armrest angled piece that is held in by strong magnets.
@@kesselsgarage awesome idea thank you for the reply. Looks great!
What type of material did you use for the upholstery?
It’s just black suede and vinyl from eBay
@@kesselsgarage Thank you for taking the time to answer. By the way, your job turned out great.👍
U got a video with it all put together?
Big Block C10 gets fresh heads and goes on it Maiden voyage!!
th-cam.com/video/3vvqwPDYFuw/w-d-xo.html
This it all put together.
Do you have the pattern?
No I’m sorry
Where’d you get the leather
We order just black vinyl rolls from eBay
@@kesselsgarage thanks and great work 🔥
Wrong magnets
What magnets should I have used?
@@kesselsgarage need neo