i use this ir sensor but it's sensitive on the normal sun light & yellow light to if i want to detect only candle flae how cn i do it from using this module. if i cannot user this sensor in open light only detect candle light what are the suggestions . thank you.
have been tested a flame blue sensor module and i noticed that this one turns LOW when becomes active, compared to your red tested module which turns HIGH. The maximum range of the detection is 0.9 meter. Bringing in the front of the IR detector a remote control similar to those who can be found for some kits which include an IR receiver for some applications such as remoted control car, the range becomes 0.5 meter and for TV remote control, becomes again 0.9 as in case when an igniter appears.
Is this also applicable with the 5 way flame sensor? And if no, can you suggest 5 way flame sensor codes where once the LED lights up, it immediately detects it on the Serial Monitor
Hi Sir, can i ask you that my buzzer and led is on directly after the code is uploaded to the board before the sensor was detected by fire but once the sensor is detected buzzer and led was off so it is like reverse. Can you please reply me what is am i wrong with this ?Thank you Sir Robotjax.
Hi, you should not have updated the code. First use the code as is and once it works, then modify it. I have explained it in the code and clearly shown that digitalWrite(ALARM,HIGH);// set the buzzer ON digitalWrite(ALARM,LOW); // Set the buzzer OFF just switch the location of the two line lines above.
Sorry I have not experience with industrial sensors . But this how it is is done, flame 🔥 always has smoke and carbon dioxide associated with it. Infrared can be added to it. So you would need to combine them all to make your own sensors that is trusted and accurate.
Thank you for the vid . I want to ask . This module can detect 700nm -1000nm spectrum of the fire, ummm so can we display that Spectrum in number in Arduino ? If can how ?
you are welcome. No you can't because it doesn't distinguish exact spectrum. But if you want to display test instead of relay or turning on an alarm, that would be doable. here the LCD1602 video robojax.com/learn/arduino/?vid=robojax-LCD1602-I2C
Hello robojex, can you tell me why my aurduino uno boards power jack is not working, i tried it many ways from 5 to 12 v dc but it not working, one more question can aurduino be used as 24 hour timer so that i can power on 4 stepper motor for different set of time?
Arduino power: it should work. Check your power adapter using multimeter to see if it produces anything above 6V. When you connect the power adapter, Arduino has voltage regulator that converts it to 5V. But when you use USB, it gets the exact 5 Volts from USB. So if your power adapter is providing thing 6V or more then it is possible that the voltage regulartor on the Arduino is defective. Timer with Arduino: Yes you can use it . But you need DS1302 Real Time Clock which has battery and keeps the time. then you can use read the time and trigger an event like turning stepper motor ON or OFF.
Robojax thank you for reply, my aurduino power jack is ok now. Can you please do me One more favour. If you can do the 24 hour real time project with aurduino and ds1302 real time clock then please make a video so that i can learn from your video. Actually i am quiet weak at code writing. Many thanks sir.
the value you read it the intensity of flame which would be very hard to use. Analog pins have value from 0 to 1024. where 0 is 0V and 1024 is 5V. you can use map function to convert it to voltage like this: Serial.print(matp(300, 0,1024, 0,5) and you can put a variable in place of 300
It depends how far, but the best option would be to have laser beam or image processing with raspberry Pi with camera. Camera can detect the the flame and trigger an alarm.
Can you give me a link to a flame sensor on AliExpress please. There are so many and some are in different colours, I'm new to electronics to its a little confusing.
Just type "flame sensor arduino" and you get tones. here is link to ebay www.ebay.ca/sch/i.html?_nkw=flame+sensor+arduino&_sacat=0 and on AliExpress www.aliexpress.com/wholesale?catId=523&initiative_id=AS_20190503035947&SearchText=flame+sensor+arduino
Hello, I have shown how do you define pins for this. do exactly the same for 2 other sensor. Define pins and code. All my videos and codes are free. but if you pay for custom code, you can contact me via robojax.com contact page. I will charge $100/hour for work. Don't forget your email in the body of message if you contacted me.
nothing will happen. As shown in video, it is the infrared elements of flame that makes the module to detect. if you try remote control of your TV, it should turn on.
@@robojax that's very interesting! I want to use the flame sensor for a school project, but I don't want to bring a real flame into the classroom. What could I use in place of a flame?
The potentiometer is multi-turn. You have to turn it 8 or 10 time before you see the change. So turn it 8 turn then test with lighter. Then then turn more and test again. in both direction and you should get it.
this module is so cheap that it would cost you 10 to 20 times more to build. But you can do it. This is infrared receiver. Search on google "infrared receiver circuit" and click on images after than and you will see 100s of projects. Good luck.
you don't need it because if you try to build it, it would cost you 10 times. But if you want to have the schematic, you can use this free program fritzing.org/
@@robojaxthank you for giving information. 🙏 can i ask another question? how about when i'm done installing the code. It is okey, that i'll use battery to my arduino? To turn it on 🤔
if you see #include.... then then there might be a library. so there is no library. Just use the provided code. The link for the code is in the description of the video.
this device could be placed closer to the a machine that might create flame and this would trigger alarm. Other application, in gas heater the igniter can be turned automatically, when gas started burning, this device could turn the igniter OFF. Or could be programmed to turn the igniter ON when there is no flame.
what diagram? the sensor schematic or the wring? Schematic may be found by doing image search or bing/google but wiring has been explained fully. but if you need it for project to show, you can get this free software and draw it fritzing.org/
at 00:44 (click on 00:44) I have explained the connections. and at 02:17 I have explained the flame pin. Which I will update the code. You will connect DO pin of the sensor to pin 2 of Arduino.I should have shown it. Thanks.
Hi :) Same question: Timeindex 4:45 where you explain the code you show a top view. What I mean is the resistor for the red LED ;) Thanks a lot. It is kind to share your knowledge with us. Big like and I subscrie to your channel (if I could I would give you 2 likes)
i use this ir sensor but it's sensitive on the normal sun light & yellow light to if i want to detect only candle flae how cn i do it from using this module. if i cannot user this sensor in open light only detect candle light what are the suggestions . thank you.
I was also wondering why it doesn't work properly when I use it as an IR receiver. This video explains well why this is so. Thanks😉
What did you understand? :)
@@goku445 Things you didnt understand😎
@@muratatatoyran6419 Well thanks a lot, that is really helping me and others that will read! Have a nice day in your bubble.
@@goku445 HaveANiceDay
@@muratatatoyran6419 Don't fart in it tho.
have been tested a flame blue sensor module and i noticed that this one turns LOW when becomes active, compared to your red tested module which turns HIGH. The maximum range of the detection is 0.9 meter. Bringing in the front of the IR detector a remote control similar to those who can be found for some kits which include an IR receiver for some applications such as remoted control car, the range becomes 0.5 meter and for TV remote control, becomes again 0.9 as in case when an igniter appears.
Thank you for sharing the infor.
Simple and extremely informative.
Thank you.
You are welcome.
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0xa2
An error occurred while uploading the sketch
avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x10
avrdude: stk500_initialize(): (a) protocol error, expect=0x14, resp=0xa2
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x10
Can we add water pump for safety in this
thank you bro u help me to finish my project..dont understand shit about coding
You are welcome. I just started a new course of Arduino for absolute beginners. Check it out. I can assure you that you will learn it.
And yes please subscribe as it helps my channel to grow. Thanks
Is this also applicable with the 5 way flame sensor? And if no, can you suggest 5 way flame sensor codes where once the LED lights up, it immediately detects it on the Serial Monitor
Never heard of 5 way flame sensor.
Hi if this sensor cant use for production what fire sensor i need to use if i use this to production ?
test it, it it works for you, make 3D print case and proper wiring. yes then you can use it if you do proper wiring to keep it safe.
Great video needed
Hi Sir, can i ask you that my buzzer and led is on directly after the code is uploaded to the board before the sensor was detected by fire but once the sensor is detected buzzer and led was off so it is like reverse. Can you please reply me what is am i wrong with this ?Thank you Sir Robotjax.
Hi, you should not have updated the code. First use the code as is and once it works, then modify it.
I have explained it in the code and clearly shown that
digitalWrite(ALARM,HIGH);// set the buzzer ON
digitalWrite(ALARM,LOW); // Set the buzzer OFF
just switch the location of the two line lines above.
Very helpful. Thanks
You are welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you
sir i am using 3 fire sensors so how i can write the code for because the buzzer only turns on with 1 sensor while all the three sensors are sensing.
if you have 3 different buzzer connected to different pen, make sure turn them ON . I don't know your code to comment.
Nice explaination sir🙌✨, can you please suggest me a flame sensor for industrial applications ?
Sorry I have not experience with industrial sensors . But this how it is is done, flame 🔥 always has smoke and carbon dioxide associated with it. Infrared can be added to it. So you would need to combine them all to make your own sensors that is trusted and accurate.
@@robojax ok thanks 🙌✨
Thank you for the vid . I want to ask . This module can detect 700nm -1000nm spectrum of the fire, ummm so can we display that
Spectrum in number in Arduino ? If can how ?
you are welcome. No you can't because it doesn't distinguish exact spectrum. But if you want to display test instead of relay or turning on an alarm, that would be doable. here the LCD1602 video robojax.com/learn/arduino/?vid=robojax-LCD1602-I2C
Robojax thanks for ur reply , then can we display the resistance of the sensor ? How the flame will efc the resistanc btw it is same with NTC ?
Hello robojex, can you tell me why my aurduino uno boards power jack is not working, i tried it many ways from 5 to 12 v dc but it not working, one more question can aurduino be used as 24 hour timer so that i can power on 4 stepper motor for different set of time?
Arduino power:
it should work. Check your power adapter using multimeter to see if it produces anything above 6V. When you connect the power adapter, Arduino has voltage regulator that converts it to 5V. But when you use USB, it gets the exact 5 Volts from USB. So if your power adapter is providing thing 6V or more then it is possible that the voltage regulartor on the Arduino is defective.
Timer with Arduino:
Yes you can use it . But you need DS1302 Real Time Clock which has battery and keeps the time. then you can use read the time and trigger an event like turning stepper motor ON or OFF.
Robojax thank you for reply, my aurduino power jack is ok now. Can you please do me One more favour. If you can do the 24 hour real time project with aurduino and ds1302 real time clock then please make a video so that i can learn from your video. Actually i am quiet weak at code writing. Many thanks sir.
Hello I have a question
At 6.32 (analog read) what is the meaning of 0 to 300? Is it distance of flame or different thing?
the value you read it the intensity of flame which would be very hard to use. Analog pins have value from 0 to 1024. where 0 is 0V and 1024 is 5V. you can use map function to convert it to voltage like this: Serial.print(matp(300, 0,1024, 0,5) and you can put a variable in place of 300
Thank you very much. I will try it.
What kind of module can be used to have a larger distant detection of flame?
It depends how far, but the best option would be to have laser beam or image processing with raspberry Pi with camera. Camera can detect the the flame and trigger an alarm.
@@robojax is there another sensor that has the farther distance detection of fire for arduino?
I don't have the rasp berry
Can you give me a link to a flame sensor on AliExpress please. There are so many and some are in different colours, I'm new to electronics to its a little confusing.
Just type "flame sensor arduino" and you get tones. here is link to ebay www.ebay.ca/sch/i.html?_nkw=flame+sensor+arduino&_sacat=0 and on AliExpress www.aliexpress.com/wholesale?catId=523&initiative_id=AS_20190503035947&SearchText=flame+sensor+arduino
Will it work outside properly? Sunlight?
Unless you test it in your particular condition, it would be hard to say. So test it.
@@robojax I doesn't actuallly
Can you please provide circuit diagram for this?
I have not seen it but here is google search result www.google.com/search?q=flame+sensor+module+schematic you may click on "image" to see more.
What if we use 3 flame sensors, what pins will we connect? We will use it for our fire fighting robot :>>
Hello, I have shown how do you define pins for this. do exactly the same for 2 other sensor. Define pins and code. All my videos and codes are free. but if you pay for custom code, you can contact me via robojax.com contact page. I will charge $100/hour for work. Don't forget your email in the body of message if you contacted me.
Hi. Nice experiment. How about if you put a hot object (eg. soldering iron or glass of hot water) in front of the sensor instead flame?
nothing will happen. As shown in video, it is the infrared elements of flame that makes the module to detect. if you try remote control of your TV, it should turn on.
@@robojax that's very interesting! I want to use the flame sensor for a school project, but I don't want to bring a real flame into the classroom. What could I use in place of a flame?
I have 3 pins for buzzer can u please tell me how to connect
Fiat try your buzzer by connecting two of its wires to +and - and find out connecting which wire turns it on, the use those two wires
What is the output voltage and current of flame sensor
I have shown the chip name. check the datasheet for the opAmp chip.
Hey bro i have already seen your video but why my Led wont turn on as the video
The potentiometer is multi-turn. You have to turn it 8 or 10 time before you see the change. So turn it 8 turn then test with lighter. Then then turn more and test again. in both direction and you should get it.
Thank you. What is the analog pin (AO) for on this module?
In most module it will output the variation of level of flame 🔥 it receives will be outputted.
@@robojax Ok thanks, big fire or small fire.
Bro is this sensor works for only fire or it also works at heat please reply broo please
Just fire and any source of Infrared. I have not tested but heat reflects infrared. So you would have to test it to find out.
Which flame sensor you use in this video?
Please tell me for my project
this is called flame sensor. The did not assign model number to it. On Amazon or eBay search for "flame sensor" and you will find it.
its called ky-026 flame sensor
Please share the mathematical modelling of flame sensor?
this is just infrared sensor as I have explained in the video. To get know how infrared sensor work, search the datasheet of the infrared sensor.
Is the code in Java
it is Arduino code . Get if free from arduino.cc
can you explain the wiring sir?
th-cam.com/video/R5LsKd1Rw-I/w-d-xo.html
Nice tutorial...Thanks
Glad it was helpful!
bro please help me....
how can i connect output of the Arduino do relay...
Watch my video th-cam.com/video/58XWVDnB7Ss/w-d-xo.html
I just want to make one for myself. Where should i start
this module is so cheap that it would cost you 10 to 20 times more to build. But you can do it. This is infrared receiver. Search on google "infrared receiver circuit" and click on images after than and you will see 100s of projects. Good luck.
@@robojax thank you dear
You are welcome.
What will happen if there is no flame but only gas is leaking ??
Nothing. it will not detect it.
Can you give me the circuit diagram of this?
you don't need it because if you try to build it, it would cost you 10 times. But if you want to have the schematic, you can use this free program fritzing.org/
@@robojaxthank you for giving information. 🙏 can i ask another question? how about when i'm done installing the code. It is okey, that i'll use battery to my arduino? To turn it on 🤔
What library did you use?
Please tell me 😢
if you see #include.... then then there might be a library. so there is no library. Just use the provided code. The link for the code is in the description of the video.
Thank you
It can also work in 3 pins? (Vcc,G,DO)?
I have explained that in the video.
It works, that you very much
can i use 12v relay..insted of buzzer
yes you can.
Thank you sir
you are welcome.
Have a look at the code and comments
pin number doesn't match
I check the code and even played the video. Both pin 8 and pin 2 are shown in video and in code. Where seems to be the problem?
what is its applications ??
this device could be placed closer to the a machine that might create flame and this would trigger alarm. Other application, in gas heater the igniter can be turned automatically, when gas started burning, this device could turn the igniter OFF. Or could be programmed to turn the igniter ON when there is no flame.
Circuit diagram please ...
See it here th-cam.com/video/R5LsKd1Rw-I/w-d-xo.html
Wiring diagram only. Do image search you will find tones .
Thank you 😊❤️
You are welcome.
@@robojax Why my flame sensor is in reserved/oposite ?. I mean it returns LOW when there is flame and HIGH when there is no fire ?
the output state is designed like that. this is normal.
@@robojax okay. Thank you
You are welcome.
Where is the diagram
what diagram? the sensor schematic or the wring? Schematic may be found by doing image search or bing/google but wiring has been explained fully. but if you need it for project to show, you can get this free software and draw it fritzing.org/
We cant see how you connected the module
at 00:44 (click on 00:44) I have explained the connections. and at 02:17 I have explained the flame pin. Which I will update the code. You will connect DO pin of the sensor to pin 2 of Arduino.I should have shown it. Thanks.
can help me about coding gsm correspond sensor temparuter and sensor smoke?
You even haven' t subscribed. Please subscribe. It is greatly appreciated. 🔔 😊
what resistors are you using?
At which part? If from the video, please point to the time on video and will look at it ( example 03:15)
Hi :) Same question: Timeindex 4:45 where you explain the code you show a top view. What I mean is the resistor for the red LED ;) Thanks a lot. It is kind to share your knowledge with us. Big like and I subscrie to your channel (if I could I would give you 2 likes)
Manuel Müller... Use a 1k ohm resistor.
❤😂