WD 40 cleans good too. Hand screw driver maybe better in this case. Never lend your trailer :-) Hope all ok after the looting etc. Do you connect a chain or wire rope from the trailer to the car? Very helpful. Tnx.
Hi The wires for my 7 pin Ford Ranger plug are different colours as to the standard colours mentioned. can you perhaps give me some advice on how to connect my 7 pin trailer plug (female) ?
Excellent video! After following all the steps, my left hand brake and park light is not working. Can anybody perhaps advise on how to check the wiring of the trailer lights? All other lights are working just fine.
Use a 12 volt power supply and connect the earth wire (white - if wired correctly) to the negative terminal of the power source and then use a probe from the positive terminal to power each of the plugs screws/holes and see how the trailer is wired.
Having just wired my trailer plug, not all lights/indicators/4 way flashers work. I only had the new tow bar fitted this week, how do I know if it's my wiring or the tow bar?? (Sorry, my excuse is I'm female and can't think outside the box!!! )
You might want to check the wiring is connected properly , if its not the trailer lights plug , then it might be the wiring of your jeep /car/van/truck or it could be a blown fuse or relay switch usually found in the engine bay or under the steering wheel.
@@seannolan3458 yeah, the wiring on the trailer blew the fuse on the car. Wiring was too old so I've bought magnetic lights to use until I rewire!!! not so much of a bargain buying something second-hand if you have to renew it all is it??? Thank you !
Nice movie, who shows the wiring diagram from the connector that is mounted on the towbar plate, everybody shows the trailer plug, can't find the wiring diagram for the other side. in other words, the wiring for the side with the dust flap on it.
@fishingkayakssa The plug with the flap is the female. The diagram to be used is exactly opposite to he male plug shown. ie. No. 1. 7. and 4. in the vertical always stay the same. No. 2. and 6. switch over and No. 3. and 5. This is the South African SABS standard.
The pin numbers and wire colours are the same. If you want to connect tow harness to your car and its a modern vehicle, you will need to go to the manufacturer or a reputable parts shop to interface unit to suit the Canbus system in your car. you cant just connect wires into the light circuits as they did on older cars.
Australia and New-Zealand use a different standard too. AS-2513 is different from ISO-1724, the key differences are that Pin-2 is for Reverse Lights and Pin-5 is for Electric Brakes. One Australian caravan manufacturer use dangerous non-standard wiring and encourage vehicle owners to dangerously modify their vehicles electrical system, making them incompatible with AS-2513 compliant trailers and caravans.
Thank you so much Sir for a very informative video. God bless you.
Great video, well explained.
Thanx so much buddy, your video was clear nd straight to the point. Presentation is awesome 👌🏿
Life saver. I know sweet FA about such matters. Thanks to this my trailer lights aglowing. Colours and numbers always works for me. Thanks 😁
Such a great video. Very informative. Thank you very much
excellent video, very clear and made simple, thanks
Realy great vid very instructive thankyou
Great Video
First class job well done!
Thanks a lot. I have to do this putting on a new plug for a borrowed trailer. The old one was wired wrong.
excellent, just what I needed, thanks 😊
thanks buddy, got it...
Wonderful and useful video, thank you for sharing. You have my like and a new subscriber.
Decent video
WD 40 cleans good too. Hand screw driver maybe better in this case. Never lend your trailer :-) Hope all ok after the looting etc. Do you connect a chain or wire rope from the trailer to the car? Very helpful. Tnx.
hi can you please show how to connect a aftermarket brake lamp to the plug on the car's side.
Hi
The wires for my 7 pin Ford Ranger plug are different colours as to the standard colours mentioned.
can you perhaps give me some advice on how to connect my 7 pin trailer plug (female) ?
Will that plug work if you have double wire ? 2 of each colours
Hi, I have a bike carrier with 8 wires and want to rewire it to a 7 pin connector, any help will be appreciated.
Excellent video! After following all the steps, my left hand brake and park light is not working. Can anybody perhaps advise on how to check the wiring of the trailer lights? All other lights are working just fine.
Use a multimeter and select dc voltage.
Use a 12 volt power supply and connect the earth wire (white - if wired correctly) to the negative terminal of the power source and then use a probe from the positive terminal to power each of the plugs screws/holes and see how the trailer is wired.
Having just wired my trailer plug, not all lights/indicators/4 way flashers work. I only had the new tow bar fitted this week, how do I know if it's my wiring or the tow bar?? (Sorry, my excuse is I'm female and can't think outside the box!!! )
You might want to check the wiring is connected properly , if its not the trailer lights plug , then it might be the wiring of your jeep /car/van/truck or it could be a blown fuse or relay switch usually found in the engine bay or under the steering wheel.
@@seannolan3458 yeah, the wiring on the trailer blew the fuse on the car. Wiring was too old so I've bought magnetic lights to use until I rewire!!! not so much of a bargain buying something second-hand if you have to renew it all is it??? Thank you !
Nice movie, who shows the wiring diagram from the connector that is mounted on the towbar plate, everybody shows the trailer plug, can't find the wiring diagram for the other side. in other words, the wiring for the side with the dust flap on it.
@fishingkayakssa The plug with the flap is the female. The diagram to be used is exactly opposite to he male plug shown. ie. No. 1. 7. and 4. in the vertical always stay the same. No. 2. and 6. switch over and No. 3. and 5. This is the South African SABS standard.
The pin numbers and wire colours are the same. If you want to connect tow harness to your car and its a modern vehicle, you will need to go to the manufacturer or a reputable parts shop to interface unit to suit the Canbus system in your car. you cant just connect wires into the light circuits as they did on older cars.
Thanks very much now I have taken my off I have only 5 wire and now ??????
if same colours then follow the tutorial, if different colours then use a multimeter on continuity to map them out.
How to buy please give link
Is this a U.K. wiring diagram.
how do you wire it to switch of the parking distance sensors
You need separate wire
I would say world wide save for North America. Of course we have to do it differently than the rest of the world.
Australia and New-Zealand use a different standard too. AS-2513 is different from ISO-1724, the key differences are that Pin-2 is for Reverse Lights and Pin-5 is for Electric Brakes.
One Australian caravan manufacturer use dangerous non-standard wiring and encourage vehicle owners to dangerously modify their vehicles electrical system, making them incompatible with AS-2513 compliant trailers and caravans.
How to by it online in India
Amazon pe milta hai bhai 600 se 1000 tak
Is jy afrikaans?.
nee
Ek dink jy jok
@@Jurgentaur ek sukkel self om vir n trailer nuwe ligte op te sit. die kleure verskil en die briek ligte het nou 3 drade en nie 2 nie
Model and specke
Bb
Black red brown green yellow
E
What if I don't have a white wire🥴
I only have green, blue, red, black, brown and yellow.
But on my plug it shows a slot for white🥴
Please We Have To Repent And Gives Our Life To JESUS CHRIST ❤️🙏 He's Worthy To Be Praise 🙏
Mujhe AP ka phone number chiya