All these installs never show what to do with the two adapter type cables they give you, does anyone know what they are for? You showed them in the video but never used them?
MonkeySharkFilms apologies. They were not needed on this truck. They are to plug the new light into the factory OE harness. The blue end attaches to the OE harness and the other to the new light plug. If you have any other questions about this or any of the other 500000 plus accessories we sell feel free to contact our knowledgeable Customer Service folks at 877-216-5446
These where on my truck when I bought it and now I have a low beam on the driver side that quit working how do I go about changing the bulb? Or would it be something else? High beam still works
Hey Geoffrey, the rubber boots on the back side of the housing is what covers the bulbs. You will need to remove the rubber boot to replace the bulb. Depending on how much room you have to work with in the engine compartment, this may require removing the lamp from the truck. Hope that helps!
J&R Contracting no. Just remove the old ones and install the new ones. If you have any other questions about this or would like more info on this item or any of the other 500000 plus accessories we sell and would like to speak to a person directly feel free to contact our knowledgeable Customer Service folks at 877-216-5446
Spec-D would be the best option for any adjustments. I know with projectors you are not able to adjust just the normal setting but you have to adjust the inside as well. They should be able to walk you through everything, though. Their number is 909-839-2533.
Do you sell the LEDs for the LED strip? My spec- D DRL DRL went out. They seem to be T10s but I plugged some in and didn't work. I don't know if it's because of the wattage or the resistor not letting enough power to get to new T10s
I would change those splice connectors to the type that have a female blade connector. Then put a male blade connector on the new wires. Removing the headlight assembly would be simple unplug, instead of trying to open a connector, or cutting wires.
Nice looking install but buyer beware . . these lights do not come with ANY instructions on how to adjust them. After looking them over closely, I am not doing the install but returning them for a better made set of projector headlamps that you CAN adjust.
@@kasken719 ok I'm confused because the instructions say connect white to white and splice it to the power on headlight wire, so I have to go back then.... thanks
@@demetrilee5246 Yeah man. I did the same thing. I ended up using a multimeter to find out which is which. I didn't want the leds flashing with my blinker. Also check your ground. I ended up having to ground the hole system because it's an old truck.
Esdras Martinez i purchased these and adjusting them is a pain, they were facinh the sky when i first put them in... i had to pull them out multiple times to get them close.
WOW AN INSTRUCTION VID I CAN ACTUALLY UNDERSTAND!!
I just wanted to say thank you sir for making this video it helped me out installed new highlights
How do u adjust the beams then
I have an 06 GMC and I got some of these halo lights and this video is better than spec-ds
To install these headlights was there any trimming done?
All these installs never show what to do with the two adapter type cables they give you, does anyone know what they are for? You showed them in the video but never used them?
MonkeySharkFilms apologies. They were not needed on this truck. They are to plug the new light into the factory OE harness. The blue end attaches to the OE harness and the other to the new light plug. If you have any other questions about this or any of the other 500000 plus accessories we sell feel free to contact our knowledgeable Customer Service folks at 877-216-5446
So these aftermarket lights come with bulbs?
Mine has 2 black 2 whites then another black and a thicker guage white wire with a black stripe through it. What is that used for?
I am having this same issue. I’m thinking it’s for a resistor kit? Really struggling with this part of the install.
Can you run regular halogen bulbs in them?
Hi Polie! Great question. Yes you can use regular halogen bulbs. Thank you!
These where on my truck when I bought it and now I have a low beam on the driver side that quit working how do I go about changing the bulb? Or would it be something else? High beam still works
Hey Geoffrey, the rubber boots on the back side of the housing is what covers the bulbs. You will need to remove the rubber boot to replace the bulb. Depending on how much room you have to work with in the engine compartment, this may require removing the lamp from the truck. Hope that helps!
do the head lights come with those blue clips?
Travis,
According to the instructions these do show to come with the blue wire connectors.
Is there any cutting to do to make the headlight fit properly?
J&R Contracting no. Just remove the old ones and install the new ones. If you have any other questions about this or would like more info on this item or any of the other 500000 plus accessories we sell and would like to speak to a person
directly feel free to contact our knowledgeable Customer Service folks at 877-216-5446
***** OK thanks
realtruck.com
they should make headlights like that for a 2000 GMC jimmy I would buy it right away
I'm having a horrible time adjusting these. Any ideas I'm not sure what to adjust
Spec-D would be the best option for any adjustments. I know with projectors you are not able to adjust just the normal setting but you have to adjust the inside as well. They should be able to walk you through everything, though. Their number is 909-839-2533.
Do you sell the LEDs for the LED strip? My spec- D DRL DRL went out. They seem to be T10s but I plugged some in and didn't work. I don't know if it's because of the wattage or the resistor not letting enough power to get to new T10s
Unfortunately, we do not have the LED's that go into the strip. You would really need to contact the manufacturer to ensure you get the proper set up.
I would change those splice connectors to the type that have a female blade connector. Then put a male blade connector on the new wires. Removing the headlight assembly would be simple unplug, instead of trying to open a connector, or cutting wires.
I like it!
Nice looking install but buyer beware . . these lights do not come with ANY instructions on how to adjust them. After looking them over closely, I am not doing the install but returning them for a better made set of projector headlamps that you CAN adjust.
my halo lights arent lighting up ?
Mine either, you ever figure out why?
Make sure you splice them into the brown middle wire on your light connector. White is for the turn signal and black is your ground.
@@kasken719 ok I'm confused because the instructions say connect white to white and splice it to the power on headlight wire, so I have to go back then.... thanks
@@demetrilee5246 Yeah man. I did the same thing. I ended up using a multimeter to find out which is which. I didn't want the leds flashing with my blinker. Also check your ground. I ended up having to ground the hole system because it's an old truck.
@@kasken719 💪🏿💪🏿💪🏿thank you for the info, fixed it
Too bad I can't find a complete video on how to adjust the headlights after the installation
Clue . . YOU CANT ADJUST THEM. What a PITA.
Not working
guaoooo
I just don't see how to adjust the aim.
Esdras Martinez i purchased these and adjusting them is a pain, they were facinh the sky when i first put them in... i had to pull them out multiple times to get them close.
@@Jester12036 how?