I wantedbto get your opinion. I have just a regular 2" water pump from the local hardware store. What size nozzle outlet and inlet should I use, or would a regular 2" pump support? Thanks
Well, I’d say most likely you could run a 2 inch suction nozzle. Your reduction would be a half inch. If I had more to go on like the specs of your pump, I could go into better detail.
Sorry I didn’t get a notification that you reposted. I think you could safely run a 2 1/2 inch suction nozzle with this pump. I think if you try to run a 3 inch nozzle you’re going to have issues with lift. I would suggest that you only go up to 2 1/2 inch suction nozzle. It’s a good in between. And you have to use a maximum of 5/8 inside Diameter Jet reduction. Your pump puts out 9000 gallons an hour, and a maximum of 39 psi.
yeah that nozzles really gonna suck in a good way. I went to work today and I usually walks quite a bit. But that's good for stretching muscles out but I still have some weak points.
Well done Tye, can't wait to see how it performs with a full length of hose. We've learned a lot from these videos. We might return to the 3D printed nozzle since it was definitely a too low a power pump to get material moving. Thanx!
My plans were to throw engine and pump together on the cheap. The pump I used to test this with I use it on my 4 inch dredge, so it's rather large for a 2 1/2 inch Suction Nozzle. The weight isn't too awful bad but what I have plans on putting together engine and pump should be half the weight or at least a third less. The best chance I have to test out this new nozzle is a buddies permission over on the other side of the state. But I don't know how the water flow is in his creek it's been dry everywhere.
It kind of all depends, on the suction nozzle at the point where the pressure incoming water tubing is welded onto the suction nozzle. There is a reduction in pipe size. What that reduction does is increased pressure at that location going in to the nozzle. That reduction is restricting the flow of water thus increasing the pressure. You can have whatever size input, water, plumbing you want but it’s hard to tell by the outside what the restriction is.
I’ve seen some suction nozzles that are pretty decent in size and they have a tiny little pressure in-line tube. Personally, I like having a larger tube or a pressure in line to whatever size comes off the pump. That’s what I want welded onto the suction nozzle tubing. I believe that gives me more strength if I have a 3 inch nozzle. I’ll have a 2 inch pressure in tubing welded onto that main body assembly. That doesn’t mean I have 2 inch Diameter of water coming into that nozzle. At the point that that incoming pressure tubing is welded onto the main body. I will have a reduction right there. For a 3 inch nozzle your minimum needs to be .75 or three-quarter inch reduction. I usually run a larger pump so I increased my reduction size just slightly maybe to 7/8 or 15/16. That is just something I do. It creates a stronger, sucking nozzle. I know some people reduce the size of the reduction in Jet. That’s why I build my own.
Oh, one last thing it’s very easy to make your own suction nozzle. All you need is the components. They’re easy to find a drill and a welder. And the determination to accomplish this task. I would rather match a suction nozzle to my pump than to wonder if the nozzle I buy is going to work right.
Great! I have watched several "nozzle" videos and haven't seen any body use a vacuum gauge to fine tune their homemade unit. You can't accurately determine how much suction your unit is generating. Also, a double venturi design makes for a more efficient nozzle.
Well you're probably right about my suction accuracy on my nozzle. I work for Construction rental company (for 22 yrs) and I check in pumps almost every day we have this gauge that I use that we put on the front side of the pump it measures suction in Hg its mounted on a round rubber plate. There's been times that I've put my hand in front of the pump to see what that suction feels like and then put the gauge on there and see what it reads. And as far as a double Venturi yeah you can do that but I am in America and I believe in brute force. So when I make an a suction nozzle I make my Jet a quarter larger than required.
Yes I need to get my 2 1/2 inch dredge going this year. On my initial testing in my water tank this nozzle prove to be substantially better than any other nozzle I've made. Quite a bit more suction with one little modification
Your tub really worked out good for your testing that’s pretty cool now you know where you need to put your welds I would suggest using that a white piece of chalk or something like you mark tires with so you can know right where your leak is so you don’t forget otherwise pretty cool glad you’re feeling better bud
Yeah the first thing I thought was oh crap I hope this aint serious I got a trip to go on soon And I thought about marking them holes but they're pretty obvious holes
Дружище нельзя просто соеденять две трубы под углом . Соеденяй трубы полуатводом с чуть большим диаметром а в месте сваривания трубы развольцуй по внутреннему диаметру полуотвода , струйник - форсунку нужно точно центровать от этого будет зависеть работа гидроэлеватора . И на последок входное отверстие на гидроэлеваторе заужай на 1/4" . Когда ты выполнишь все эти не сложные условия ваш гидроэлеватор будет хорошо работать и проктически не будет засоров .
ну, сэр, моя насадка работает. То, что вы хотите, чтобы я сделал, немного сложнее. Я видел, как люди делали насадки, как вы предлагаете. Если бы у меня был инструмент, позволяющий сделать то, что вы говорите, я бы сделал это. Билл Дальк делал насадку с входным отверстием меньше, чем секция, к которой присоединяется шланг. Я не совсем понимаю насчет уменьшения на четверть дюйма. nu, ser, moya nasadka rabotayet. To, chto vy khotite, chtoby ya sdelal, nemnogo slozhneye. YA videl, kak lyudi delali nasadki, kak vy predlagayete. Yesli by u menya byl instrument, pozvolyayushchiy sdelat' to, chto vy govorite, ya by sdelal eto. Bill Dal'k delal nasadku s vkhodnym otverstiyem men'she, chem sektsiya, k kotoroy prisoyedinyayetsya shlang. YA ne sovsem ponimayu naschet umen'sheniya na chetvert' dyuyma.
I hope I translated to the right language. There’s always better ways of making a Suction Nozzle. There are ways to increase your performance. What I am doing here, and showing a basic construction of a suction nozzle is to give people the basics of making one their selves. A better main body would be a mandrill bent 45. I’m just using what I have at hand.
Oh, also I did get the jet dead centered, I probably made 14 suction Nozzles in the last 12 years and I’ve had a few that weren’t dead centered. This one was perfectly centered and aligned.
Yeah that's true maybe on a hot day it would be refreshing to get sprayed with a little creek water. I'm still going to get the wire feed out and drop a little hot metal in those two spots
I had something like this happened to me 25 years ago in the gym. But my joint was actually popped out for almost a year. I think i just need some rest. But it's not gonna keep me out of the creek. That's how I get all my exercise
@@IowaGoldProspectors I blew my shoulder out digging a trench to the garage for electric, snapped a ligament, this was like 7 years ago, thought it would heal on it's own but never did and sometimes it reminds me lol never fun to get wounded and these days I avoid going to any doctor at almost any cost, i am one who does not agree with what's going on last two years, have fun
@@diggindiggenit6540 I severely twisted an ankle and I broke many bones in my foot back in 2007 and I took close to five years to heal up. I should've had an MRI done but I never did. I actually had a appointment to see a doctor today at 10 o'clock but canceled because my hip feels so good.
Well, I made this two years ago I went down to my local muffler shop bought about 16 inches of 2 1/2 inch pipe. I had them cut it at a 60° angle rotate those two pieces 180° and re-weld it. If I were to do that pipe again, I would buy a mandrel bent tube. What’s the prices on this? I don’t know it’s gone up because of inflation. Don’t have a freaking clue. I’m pretty sure if you’re looking to make a suction nozzle you should already know, roughly how big things are going to be. The only problem people have is knowing that you need to put a Jet or reduction in on your suction nozzle. I explained well enough how to put your nozzle together, the only thing you need to know is what size your Jet needs to be if you’re going to make a suction nozzle.
motorum 2,5 hp gücünde. 1,5 inch su çıkışı var. 2 inch emme bölümü olan bir nozul uygun olur mu. Bu motor için en uygun nozulu yapmak istiyorum. uygun ölçüleri bana yazarsanız minnettar olurum. Hyundai hpw15
inçlik bir emme memesini gayet iyi çalıştırabilmelisiniz. 2 inçlik emiş başlığınız için jetinizin yarım inç olması gerekir. İsterseniz biraz daha büyüyebilirsiniz ama çok değil. Pompa çıkışınız 1 1/2 inç olduğundan, ağzınıza doğru 1 1/2 inçlik bir hortum çalıştırın.
Tekrardan merhaba. 1 1/2 inclik nozul yapmaya karar verdim. Risk almak istemiyorum. Pompam yakin zamanda elime ulasacak. Jetin ölçüsü ne olmalı. Emme kisminin dörtte biri kadar olmasi uygun olur mu.
Thanks for the add, yeah I've been making Suction a Nozzle for myself on different dredges I've been tinkering around with for quite a few years. I did a little something different this year on making that nozzle and I really think it increased the suction quite a bit. I hopped over to your channel And subscribed also, I left you a comment on a video that you posted recently about thermal city. I don't remember I wanna say that I was there a couple years ago is that in North Carolina or is that in Georgia?
I wantedbto get your opinion.
I have just a regular 2" water pump from the local hardware store.
What size nozzle outlet and inlet should I use, or would a regular 2" pump support?
Thanks
Tell me the specs on your regular pump. What’s the gallon per hour and feet of head.
Well, I’d say most likely you could run a 2 inch suction nozzle. Your reduction would be a half inch. If I had more to go on like the specs of your pump, I could go into better detail.
@@IowaGoldProspectors mine says a max flow of 150 gallons and shut off feet 92.
Sorry I didn’t get a notification that you reposted. I think you could safely run a 2 1/2 inch suction nozzle with this pump. I think if you try to run a 3 inch nozzle you’re going to have issues with lift. I would suggest that you only go up to 2 1/2 inch suction nozzle. It’s a good in between. And you have to use a maximum of 5/8 inside Diameter Jet reduction.
Your pump puts out 9000 gallons an hour, and a maximum of 39 psi.
@@IowaGoldProspectors thank you.
Glad you feeling better. Thank your video
Thanks Barb👋
That looks like a fun toy. Cool to see the jet inside the nozzle. Glad you're feeling better!
yeah that nozzles really gonna suck in a good way. I went to work today and I usually walks quite a bit. But that's good for stretching muscles out but I still have some weak points.
Well done Tye, can't wait to see how it performs with a full length of hose. We've learned a lot from these videos.
We might return to the 3D printed nozzle since it was definitely a too low a power pump to get material moving. Thanx!
My plans were to throw engine and pump together on the cheap. The pump I used to test this with I use it on my 4 inch dredge, so it's rather large for a 2 1/2 inch Suction Nozzle. The weight isn't too awful bad but what I have plans on putting together engine and pump should be half the weight or at least a third less. The best chance I have to test out this new nozzle is a buddies permission over on the other side of the state. But I don't know how the water flow is in his creek it's been dry everywhere.
Thankyou sir I learn what I can do you have a great day
you're welcome
do you have a great day as well?
great work fam. keep at it fam. that was cool. GOLD SQUAD OUT!!!
Thanks for watching Gold Squad
I see nozzles with different size input water. What is the difference? Does the larger input water give more suction?
It kind of all depends, on the suction nozzle at the point where the pressure incoming water tubing is welded onto the suction nozzle. There is a reduction in pipe size. What that reduction does is increased pressure at that location going in to the nozzle. That reduction is restricting the flow of water thus increasing the pressure. You can have whatever size input, water, plumbing you want but it’s hard to tell by the outside what the restriction is.
I’ve seen some suction nozzles that are pretty decent in size and they have a tiny little pressure in-line tube. Personally, I like having a larger tube or a pressure in line to whatever size comes off the pump. That’s what I want welded onto the suction nozzle tubing. I believe that gives me more strength if I have a 3 inch nozzle. I’ll have a 2 inch pressure in tubing welded onto that main body assembly. That doesn’t mean I have 2 inch Diameter of water coming into that nozzle. At the point that that incoming pressure tubing is welded onto the main body. I will have a reduction right there. For a 3 inch nozzle your minimum needs to be .75 or three-quarter inch reduction. I usually run a larger pump so I increased my reduction size just slightly maybe to 7/8 or 15/16. That is just something I do. It creates a stronger, sucking nozzle. I know some people reduce the size of the reduction in Jet. That’s why I build my own.
That reduction will determine what the throttle setting of your pump needs to be.
Oh, one last thing it’s very easy to make your own suction nozzle. All you need is the components. They’re easy to find a drill and a welder. And the determination to accomplish this task. I would rather match a suction nozzle to my pump than to wonder if the nozzle I buy is going to work right.
@@IowaGoldProspectors Thanks
Great!
I have watched several "nozzle" videos and haven't seen any body use a vacuum gauge to fine tune their homemade unit. You can't accurately determine how much suction your unit is generating. Also, a double venturi design makes for a more efficient nozzle.
Well you're probably right about my suction accuracy on my nozzle. I work for Construction rental company (for 22 yrs) and I check in pumps almost every day we have this gauge that I use that we put on the front side of the pump it measures suction in Hg its mounted on a round rubber plate. There's been times that I've put my hand in front of the pump to see what that suction feels like and then put the gauge on there and see what it reads. And as far as a double Venturi yeah you can do that but I am in America and I believe in brute force. So when I make an a suction nozzle I make my Jet a quarter larger than required.
I will happy to see it work
Yes I need to get my 2 1/2 inch dredge going this year. On my initial testing in my water tank this nozzle prove to be substantially better than any other nozzle I've made. Quite a bit more suction with one little modification
Your tub really worked out good for your testing that’s pretty cool now you know where you need to put your welds I would suggest using that a white piece of chalk or something like you mark tires with so you can know right where your leak is so you don’t forget otherwise pretty cool glad you’re feeling better bud
Yeah the first thing I thought was oh crap I hope this aint serious I got a trip to go on soon
And I thought about marking them holes but they're pretty obvious holes
nice video.can u help a little bit.For regular pump how much has to be the smallest pipe diameter if the suction nozzle is 3"?
for 3 inch nozzle your jet needs to be at least 3/4", or if you're across the pond, your millimeter size is going to be 19.05 mm
if any of this is helpful to you, I would appreciate it if you give me a subscription it helps my channel
Дружище нельзя просто соеденять две трубы под углом . Соеденяй трубы полуатводом с чуть большим диаметром а в месте сваривания трубы развольцуй по внутреннему диаметру полуотвода , струйник - форсунку нужно точно центровать от этого будет зависеть работа гидроэлеватора . И на последок входное отверстие на гидроэлеваторе заужай на 1/4" . Когда ты выполнишь все эти не сложные условия ваш гидроэлеватор будет хорошо работать и проктически не будет засоров .
ну, сэр, моя насадка работает. То, что вы хотите, чтобы я сделал, немного сложнее. Я видел, как люди делали насадки, как вы предлагаете. Если бы у меня был инструмент, позволяющий сделать то, что вы говорите, я бы сделал это. Билл Дальк делал насадку с входным отверстием меньше, чем секция, к которой присоединяется шланг. Я не совсем понимаю насчет уменьшения на четверть дюйма.
nu, ser, moya nasadka rabotayet. To, chto vy khotite, chtoby ya sdelal, nemnogo slozhneye. YA videl, kak lyudi delali nasadki, kak vy predlagayete. Yesli by u menya byl instrument, pozvolyayushchiy sdelat' to, chto vy govorite, ya by sdelal eto. Bill Dal'k delal nasadku s vkhodnym otverstiyem men'she, chem sektsiya, k kotoroy prisoyedinyayetsya shlang. YA ne sovsem ponimayu naschet umen'sheniya na chetvert' dyuyma.
I hope I translated to the right language. There’s always better ways of making a Suction Nozzle. There are ways to increase your performance. What I am doing here, and showing a basic construction of a suction nozzle is to give people the basics of making one their selves. A better main body would be a mandrill bent 45. I’m just using what I have at hand.
Oh, also I did get the jet dead centered, I probably made 14 suction Nozzles in the last 12 years and I’ve had a few that weren’t dead centered. This one was perfectly centered and aligned.
Feel free to post how to video on TH-cam on how to make a suction nozzle. Send me a link when you do.
That thing sucks 👍🏻pretty good I would say 👍🏻👍🏻can’t see or feel leaks when in water lol
Yeah that's true maybe on a hot day it would be refreshing to get sprayed with a little creek water. I'm still going to get the wire feed out and drop a little hot metal in those two spots
Working real good, take care of that hip ouch
I had something like this happened to me 25 years ago in the gym. But my joint was actually popped out for almost a year. I think i just need some rest. But it's not gonna keep me out of the creek. That's how I get all my exercise
@@IowaGoldProspectors I blew my shoulder out digging a trench to the garage for electric, snapped a ligament, this was like 7 years ago, thought it would heal on it's own but never did and sometimes it reminds me lol
never fun to get wounded and these days I avoid going to any doctor at almost any cost, i am one who does not agree with what's going on last two years, have fun
@@diggindiggenit6540 I severely twisted an ankle and I broke many bones in my foot back in 2007 and I took close to five years to heal up. I should've had an MRI done but I never did. I actually had a appointment to see a doctor today at 10 o'clock but canceled because my hip feels so good.
Spek?
I need more information on what you’re asking
@@IowaGoldProspectors how much is the pipe? how many degrees is the curve? how long is the front and how long is the back?
Well, I made this two years ago I went down to my local muffler shop bought about 16 inches of 2 1/2 inch pipe. I had them cut it at a 60° angle rotate those two pieces 180° and re-weld it. If I were to do that pipe again, I would buy a mandrel bent tube. What’s the prices on this? I don’t know it’s gone up because of inflation. Don’t have a freaking clue. I’m pretty sure if you’re looking to make a suction nozzle you should already know, roughly how big things are going to be. The only problem people have is knowing that you need to put a Jet or reduction in on your suction nozzle. I explained well enough how to put your nozzle together, the only thing you need to know is what size your Jet needs to be if you’re going to make a suction nozzle.
motorum 2,5 hp gücünde. 1,5 inch su çıkışı var.
2 inch emme bölümü olan bir nozul uygun olur mu. Bu motor için en uygun nozulu yapmak istiyorum. uygun ölçüleri bana yazarsanız minnettar olurum.
Hyundai hpw15
inçlik bir emme memesini gayet iyi çalıştırabilmelisiniz. 2 inçlik emiş başlığınız için jetinizin yarım inç olması gerekir. İsterseniz biraz daha büyüyebilirsiniz ama çok değil. Pompa çıkışınız 1 1/2 inç olduğundan, ağzınıza doğru 1 1/2 inçlik bir hortum çalıştırın.
@@IowaGoldProspectors çok çok teşekkürler.
iyi şanslar ve rica ederim
Tekrardan merhaba. 1 1/2 inclik nozul yapmaya karar verdim. Risk almak istemiyorum. Pompam yakin zamanda elime ulasacak. Jetin ölçüsü ne olmalı. Emme kisminin dörtte biri kadar olmasi uygun olur mu.
Cevabınız evet, emişin 1/4'ü kadar. Ondalık olarak .375, yani 9.525 mm ama ben 10 mm'ye giderdim. Jet boyutunuz için.
Wow wonderful
thank you
Awesome design that thing looks like it would suck the warts off a toad lol new to your channel
Thanks for the add, yeah I've been making Suction a Nozzle for myself on different dredges I've been tinkering around with for quite a few years. I did a little something different this year on making that nozzle and I really think it increased the suction quite a bit. I hopped over to your channel And subscribed also, I left you a comment on a video that you posted recently about thermal city. I don't remember I wanna say that I was there a couple years ago is that in North Carolina or is that in Georgia?
@@IowaGoldProspectors its in North Carolina thank you sir I'm courious how well that nozzle works
I'm going to get it out here in two weekends and do some dredging with that nozzle
@@IowaGoldProspectors can't wait to see