I cannot thank you enough for showing how to setup, run, and perform essential calculations for this test. Plus those tips about accounting for friction from the bearings, as well as the load from the cell pressure... man, this is a life-saver. A lot of steps and setup - I can see why labs charge so much for this test.
Wish I would have had this 3 years ago. Here I am writing a procedure for my company following basically the same format you made these videos in. Great work!
Good morning thanks for this great lesson and I think that you tired because this test consists of more detailes so that I have a question that can we do test uu triaxial in the libratory only because it is quick
Thanks for the extensive videos. I'm learning alot. I have a question about the determination of the stiffness parameters. Based on the deviatric stress and the strain the E50 can be determined from a triaxial shear test. What if we would be doing a multi stage triaxial shear test. The testmonster would have 3 different stages where it is being tested. What stage is suited best for the determination of E50? Another question is about the reference stress. Alot of soil mechanics (in Holland) are based on a reference stress of pref = 100 kPa. Are the triaxial shear tests results based on a pref of 100 kPa, or does a correlation have to be used to determine the reference value of E50?
Sir, so far i know in CU test first comes saturation then consolidation then the undrained shear part. You have completed the saturation stage and then started the shear part. Why not consolidation?
Sir as we see this test is CU that means undrained at sharing stage excess pore pressure takes all the stress.... Due to that sample never gets fail...... Effective Stress on soil partical is same before and after loading... Sir plz explain I cannot understand... Consider S=100%
Very goes efforts sir, but i dont get it... How can we shear before consolidation. B value is for saturation,after that we consolidate it right??....May be you missed part of consolidation to include in video
For the purpose of my class I'm not really measuring consolidation. The soil tested here is a stiff silty sand. Very little consolidation. It saves time in getting the soil saturated if we start consolidation before 100% saturation and doesn't really matter for the purposes of my class. But you are correct. Normally, one should saturate the sample before consolidation.
The confining stress is kept constant by the pressure regulators on the panel. The drain line to the sample is closed during the shear portion of the test, but the line to the cell pressure is open, thus creating a constant total confining stress. The effective stress does change significantly due to shear induced pore pressures.
@@introductiontogeotechnical4976 can i perform the test by keeping prefix value of back pressure? i mean different effective stress? in that case, i have to keep drain line open which is connected to back pressure line. is it?
The best part of the videos is your voice ...very precise and clear
I cannot thank you enough for showing how to setup, run, and perform essential calculations for this test. Plus those tips about accounting for friction from the bearings, as well as the load from the cell pressure... man, this is a life-saver.
A lot of steps and setup - I can see why labs charge so much for this test.
Wish I would have had this 3 years ago. Here I am writing a procedure for my company following basically the same format you made these videos in. Great work!
Great work. Thank you so much!
Thank you so much!!
Good morning thanks for this great lesson and I think that you tired because this test consists of more detailes so that I have a question that can we do test uu triaxial in the libratory only because it is quick
Thank you
really amazing
Thanks for the extensive videos. I'm learning alot. I have a question about the determination of the stiffness parameters. Based on the deviatric stress and the strain the E50 can be determined from a triaxial shear test. What if we would be doing a multi stage triaxial shear test. The testmonster would have 3 different stages where it is being tested. What stage is suited best for the determination of E50?
Another question is about the reference stress. Alot of soil mechanics (in Holland) are based on a reference stress of pref = 100 kPa. Are the triaxial shear tests results based on a pref of 100 kPa, or does a correlation have to be used to determine the reference value of E50?
ok I have a question, you say you're saturating the sample but at the same time the sample is consolidated.... could you explain?
Thank you!
Sir, so far i know in CU test first comes saturation then consolidation then the undrained shear part. You have completed the saturation stage and then started the shear part. Why not consolidation?
Sir as we see this test is CU that means undrained at sharing stage excess pore pressure takes all the stress.... Due to that sample never gets fail...... Effective Stress on soil partical is same before and after loading... Sir plz explain I cannot understand... Consider S=100%
Very goes efforts sir, but i dont get it... How can we shear before consolidation. B value is for saturation,after that we consolidate it right??....May be you missed part of consolidation to include in video
For the purpose of my class I'm not really measuring consolidation. The soil tested here is a stiff silty sand. Very little consolidation. It saves time in getting the soil saturated if we start consolidation before 100% saturation and doesn't really matter for the purposes of my class. But you are correct. Normally, one should saturate the sample before consolidation.
Thank u
The speed up part really makes me lol
When we apply deviator stress... Due to addition of rod volume into specimen cell pressure get changed....so sir how we take cell pressure as constant
The confining stress is kept constant by the pressure regulators on the panel. The drain line to the sample is closed during the shear portion of the test, but the line to the cell pressure is open, thus creating a constant total confining stress. The effective stress does change significantly due to shear induced pore pressures.
This video will explain the triaxial test steps more clearly th-cam.com/video/hq4UlLm8oIs/w-d-xo.html&lc=UgxmQGdVCAiXCmSeBeB4AaABAg
@@introductiontogeotechnical4976 can i perform the test by keeping prefix value of back pressure? i mean different effective stress? in that case, i have to keep drain line open which is connected to back pressure line. is it?
learn from home XD
Thank You