ฝัง
- เผยแพร่เมื่อ 3 พ.ค. 2024
- In today's video I will help you solve the arduino uno problem with uploading to the board in windows 10. This video simply contains a guideline in helping you figure out how to solve the arduino uploading problem
arduino intro: • Arduino uno basics exp...
esp32 board: • Sparkfun ESP32 thing I...
arduino troubleshooting: goo.gl/VGHuAd
arduino forum: forum.arduino.cc/
driver 1: • Fix Arduino "Unable to...
driver 2: • Arduino UNO and Mega W...
driver explanation: • Fix Arduino "Unable to...
bootloader arduino: goo.gl/14Kjpb
bootloader: • How to Burn Arduino bo...
All my code will be available on my Patreon page:
/ 23349519
www.patreon.com/asali
Arduino kits:
Arduino Uno Starter Kit (original version)
Affiliate link: amzn.to/2H4femD
Normal link: goo.gl/v4NFAU
Arduino Uno Starter Kit (cheap version)
Affiliate link: amzn.to/2R2a6Uu
Normal link: goo.gl/Z3Ekup
Arduino Uno
Affiliate link: amzn.to/2R47IwA
Normal link: goo.gl/mdSGRH
Credits:
Music:
Classique - Francis Preve
Thumbnail & video icon's:
arrow: www.flaticon.com/authors/pixe...
Hello sir! Huge thanks to you. It's 3am here and I am having exhibition of my Arduino project in 8am morning, I was frustrated as hell. Lost all hopes and went off to bed. Then I saw your video and came to know that 0 and 1 are serial port pins and they didn't allow my program to update. I got up and tried and succeeded. You helped me like a miracle, will never forget this moment. Thank u so much for posting this video! 😇
Happy to hear my video helped you out buddy! :)
exactly the same thing happening to me rn but its 6;50 am
Unplugging from pins 0 and 1 just ended hours of frustration for me. Thank you so much!
I too had the pins plugged in the Arduino as well. As soon as I unplugged my servo from it I was able to upload my sketch. Thanks so much!
Vic
Canada
THANK YOU! My PORTS were all connecting blutooth. So I turned it off and re-opened the program to get my USB port to recognize my UNO. It finally uploaded that damn blinking sketch after 2 days. I am very green at this and your video was extremely helpful!
Sir Thank you a lot! I just wanted to learn something on my own and if I would have failed in just starting the ARDUINO UNO my confidence would be lost before going any further and I would have thought I can't do this !! THANK YOU ALOT!! GOD GIVE YOU LOT OF SUCCESS IN THE FUTURE!! I AM SUBSCRIBED!! (problem was drivers )
Thank you so much. I use Uno with Labview for Bluetooth communication program. So I used Tx and Rx pins. That was the problem! I unplugged Arduino's 0 &1 pins and it's done!
you tube algo is making me cry, i got you like after 3-4 days of continuous hunt for my problem , thank you bro !
i haven't updated the drivers...now my arduino is working properly...thanks bro..good tutorial
THANK YOU. Solved my (NOT) uploading problem by turning off firewall (win10) for a little while.
Thank you a lot! i was making esp32 and it cracked arduino programme settings. now i fixed it! Thank you!
I struggled with esp for along time until I started using python. I would seriously recommend doing all ESP projects with python. It’s fast, clean and so much easier to work with.
Thank you so much! This helped me A LOT with my problem
Thanks for the video after installing the drivers my port option came back!! Thank You
Thank you I unsuccessfully tried to program the arduino for one year thanks
Really thank you!!!!! I am making project useless box and this video saved me hours of working again thanks.
hey dude you're the best, i did a stupid mistake by using a charging cable and i did everything from installing the drivers all of them even the ones that my board is not concerned with, but it was the DAMN cable.
you are great sir u saved my money i thought my arduino had problem but it was port thank you so much sir...
Suberb, i was facing problem from a lot of time. i also watched a lot of videos but you give the solution in this video
i cant thank you enough my good sir youve helped me
You're welcome buddy!
Your video been very helpful. Great👍
Thanks man, you saved me a shit ton of time
Thank you this helped me a lot
Thank you a lot . It really helped me
Thanks a lot. I solved the problem because of this video.
Disconecting 5V and GND while uploading worked for me. when I tried again to do it while plugged, I've got the same issue as before.
Honestly, Thank you so much!
thanks for the help mate
Thank you very much it worked
Thx thumb up for this video u helped me
OH MY GID THANK YOU SOOOOOOOOOOOOO MUCH
You are a genius bro
You're genius!
this is permenent flashing ? or restart then erace ?
thanks a lot super helpful
I love you bro ! Its working..
Thats Right ...Thanks
Thanks and godbless 😍 very helpful tutorial .. done subscribed 😊
thenks
What you have done for the port??? Please reply
Maraming salamat sir
This video help me .Thanks
hello sir. In my pc's device manager ,there is neither port option nor other devices option..what should i go for?
THank you so much man
thank you
tnx a lot solve my problem
Sir i am doing a voice controlled robot and my arduino is not getting the code uploaded.Should i remove the 0 and 1 pins and try uploading???
Thank you thank you thank youuu
You're welcome welcome welcomeee
Eu tive um problema de comunicação com o meu Arduino, após vários meses de funcionamento sem problemas, resolveu dar um problema de comunicação com a Porta COM CH340. Depois de muito verificar e tudo estava bem, cheguei á conclusão que tinha sido uma atualização do windows que atualizou os drivers CH340. A única maneira de resolver, é ir à respetiva porta e reverter para os drivers anteriores. Espero que ajude.
In my case I am getting
Sketch used 3796 of program storage space.maximum is 32256 bytes global variables use 190 byte of dynamic memory leaving 1858 byte for local variable.
Hello sir,I saw your video but instead of getting com3 i'm getting com7,and doing the steps u said its still not working..please tell something..thanks
I have question
when I enter code in arduino and save it before saving the code it closed I mean ide closed
Sir I have facing a problem in degitalwrite declaration please tell me how I can fix it
Hi sir
I have tryed all your methods of trying to get it to work put not even the COM its plugged into is showing can you help me
I am using mega 2560 with python using pyfirmata
Since i made communication with my program i was using it through its port no ttyACM0 ( i can see it by its ide installed in my pc) with board selected as Arduino mega 2560 nd all was working fine
But from last two days suddenly and automatically it changes its port no continuosly
Means lets say currently the Port no is ttyACM0...
Now if i do power on and off then i try to connect it then it shows errror in communication
Then if i check it then it showing that its port no is ttyACM1 now
Similarly next time ttyACM2 and so on
May i know why this is happening?
Any idea?
Good
sir in my one i cant upload a file to the arduino can you solve this problem
thanks alot
Hello Valued Expert,
May you help me to get a sketch for reading and changing SDcard CID.
Thanks in advance!
Try closing Ultimaker Cura if you have it running, that was my problem
Hello
I'm facing the avrdude:stk500v2_RevieveMessage(): timeout error.
This is a common problem online with no definite solution
I tried update driver but still it showing programmer is not responding my board is arduino uno plz help
Sorry for the late response! What brand is your Arduino made of? This is important for installing the correct drivers!
Love u broo
My led on my arduino uno board is not blinking on pressing the reset button and code is not uploading to it can you please help me 🙏🙏
hello sir,
i have a case....
arduino uno: "error connecting to the avr! retrying in 10s (no response from the board: list index out of range, please check the connection, port setting or reset the avr)"
how is the solution ..... Thanks
i have driver, i removed RX and TX wires, i have bootloder and still not uploading
i have two arduinos and two cables one of the arduinos work properly while the other does not
the other arduino does not even light up its on led
its like its dead
can someone help
my arduino leonardo the COM 7 is gone and i can't install or erase a new code
good research
hey pls help
i have this arduino uno, it always error when uploading, i check everything on the software and everything was right. but my arduino LED always blinking even though i reset it. is this one of the problem that might be the cause i can't upload?
Are you getting any kind of errors when uploading? If so please tell me which one
@@asali-channel it says sync error, and programer not responding, do you know what's that mean?
I might know, can you tell me what type of arduino you have? Duemilanove, Genuino, etc? (I don't mean uno)
@@asali-channel i have genuino
Hlo sir This is Trilok Singh from India.sir my Arduino uno 3 is uploading show error again and again .and same nano .so please tell me about something
All I get is
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x27
please help me out i am making tiny sorter google experiment
If you or anyone in the comments can help me out, my takes a incredibly long time to upload it never finished uploading and I don't know what the issue is
how to fix if orange led not blinking
I'm getting this error while uploading the program.Please Help me.
"
Arduino: 1.8.5 (Windows 10), Board: "Arduino/Genuino Uno"
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
"
Hey I have also made video on this problem.
Oh great to hear, I'll check it out! :)
@@asali-channel Oh Thanks it will be pleasure for me.
Thankyou so much bro! you saved my ass lmao
opa, amigo, tenho arduino uno, e da erro quando tento carregar para a placa, como resolvo isso? como você resolveu o seu?
Happy to hear it worked out for you!
If your arduino still doesn't work, here's a link that I found helpful:
www.hobbyelectronix.com/2020/05/arduino-troubleshooting_20.html
why i always get AVRdude : stk500_getsync : programmer is not responding. my port and my board is on correct place ..??
Sorry for the late response! Have you tried to unplug all wires before uploading? Once it has uploaded try to reconnect the wires
@@asali-channel i already tired that
Perhaps yours is broken, I suggest you try again to follow every step I took in my video, from what brand is your Arduino Uno?
most probably his bootloader is destroyed.. that was the case in mine... I got another Arduino and used it as
ISP to burn the bootloader into the previous one.. @@@asali-channel
How to reset an arduino?
There should be a small red button on your Arduino Uno
ITS SHOWING
avrdude: ser_open(): can't open device "\\.\COM11": Access is denied.
Problem uploading to board. See www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
CAN ANYONE HELP ??????????/!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@@abrorbobomurodov2361 what???
My arduno is broken L light is not working
errors messages are typical than codes
its showing programmer is not responding please help
No wires are connected to pin 0 & 1?
@@asali-channel i am not understanding pin 0 and 1
@@asali-channel how to do please help i am new to aurdino its urgent
No wires should be connected to pin 0 & 1 as these are part of the serial interface so please unplug any wires connected to those pins
@@asali-channel i am only trying to upload program on aurdino nothing is connected but still showing error can i try that aurduino on win 10
Problem solved driver problem
Anyone having exit error 1
This means there is an error in your code:
forum.arduino.cc/index.php?topic=365466.0
no sound
hi, I am using arduino nano and could not get rid of the problem .
Here is Problem below.
Sketch uses 930 bytes (3%) of program storage space. Maximum is 30720 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x28
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x28
Problem uploading to board. See www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
Invalid library found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a: no headers files (.h) found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a
Invalid library found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a: no headers files (.h) found in C:\Users\Habib Daood Rathore\Documents\Arduino\libraries\sketch_dec11a
Can you please upload you're code into a pastebin aswell please? Apparently you have an invalid library somewhere so your code could be helpfull also have you imported the correct libraries?
@@asali-channel The invalid library has nothing to do with the programmer not responding. The problem is driver related. Windows sees it but incorrectly and the IDE only knows what com port.
@@mikelee1906 thanks for your response, I appreciate the help!
For Nano try using the ATmega328P(old bootloader) instead of the ATmega328P. Under Tools Menu then Processor: select ATmega328P(old bootloader). This solves the problem 80% of the time. Good luck!!
@@mikelee1906 well what about uno
Doesn't he sound a bit like Mr cheese?
Lol
Lost
Nope. Did not solve problem. Have about $200 in Arduino product and it's all bricks at this point. All worked last fall. My firm opinion of most of IT right now is it's all trash and what does work is broken by people making updates. It's not worth the time or head ache to even teach the next generation how to use it.
blah blah blah you talk to say nothing
Thanks Man
You're welcome!