This was really fun to watch. And a pretty outcome, for sure. Might I make a couple of suggestions? I know it would be more work, but narration would be MUCH preferred over just music. You're a craftsman. I would love to hear your tips & tricks as you go through some of your steps here. Also, I'm an electronics guy and I HATE seeing wires splay out from the corner of such a nice piece! One thought would be to make one dowel hollow and route that power wire down through that. Now that wire would sneak almost invisibly out of the bottom of your base and off towards the back. Anyway, not to nit pick as this was a beautiful piece in its own right. regards, Dan
Fantastic. The only thing I would try to do is on a future one, have the cord come out near one of the posts and a groove carved in the post so as to “hide” the cord, then come out the bottom of the wood base with a groove so it lays smooth on the bottom and exits to the side. Hope that makes sense - just trying to not have the cord so obvious. In fact, if embedded in a post groove, it could be resined over with a color in the light to mask the cord. Each post could have grooves with resin color - might pick up light from the top and travel a bit into the post. But no matter - terrific and very imaginative work. Thanks for sharing. Can’t wait to watch more.
man would you please tell me what kind of usb charguer you are using for this work? I really need the info because I used a regular 5volts 1.0 amp and it burned the wired led
Да. классно! Но немного грустно выглядит, я бы веточки покрасила белой краской и приклеила искусственный снег и немного серебряных блёсток. Тогда получился бы зимний светильник :)
Increíble! Queda preciosa! Una pregunta, ¿la reacción térmica de tanta resina a la vez no deshace el molde? ¿no se debe aplicar en varias capas? Lo pregunto por que a mi me ha pasado. Muchas gracias y fantástico trabajo!!!
Tengo un problema, las dos veces que he intentado hacer una, el epoxy se ha calentado mucho y me ha quedado el circuito del Led, algún consejo o resina que no coja tanto calor??. Gracias
Si la fiebre es intensa, puede encontrar formas de bajar la temperatura, como poner en el refrigerador, soplar aire o poner un poco de hielo o agua fría fuera del molde.😉
Buonasera... Che resina usi!? La mia ha un rapporto diverso... 100gr.+60 gr. di indurente... Ma la tua è molto più brillante!!! 👍👍 Puoi inviarmi il link?... Grazie e congratulazioni
Good night, a question I live in Mexico and I can not find these lights, could you tell me with what name I look for them only in the center LED strips are obviously not used for your beautiful works or they are only sold in your beautiful country as I do my dear friend my name is Adrián Martínez I would appreciate your comments, thank you
THAT ITS AWESOM :-) Cant u tell which is the mixture you use to make since it is totally unknown to me. It does not exist or does exist in my country, but it is so inaccessible or too expensive, so no one uses it and it is not seen often. Thank you
![[BAEMON NEWS 7] NEW ALBUM COMING IN](http://i.ytimg.com/vi/wtVeAPimOyo/mqdefault.jpg)
This is one of the nicest resin cast lights I've seen yet.
Thanks a lot Ted Weddell 😊
Even without the branches put in just the coloured lights in clear resin would be stunning.
Good job!
It's good when the hands are synchronized with the head !!!) It turned out great !!!)
This lamp is so pretty and unusual. Amazing!
Thanks a lot kath oakes 😊
Slightly organic modern
I have a new hobby now thank you for sharing this! My parents gonna love this artwork 😍😍😍😍
Super tare 👍👍👍👍🌽🌽
Красивый получился кубъ👍😉
напомнило мне детство...как зимой по льду ходил на реке и там такое видел!
Such beauty. I'm truly in love with it. Many blessings
Thanks a lot Olga Colón 😊
Beauty in simplicity. Thanks for sharing.
Thanks a lot Yolanda Fernandes 😊
Una verdadera belleza. Felicitaciones!!👏👏👏. Saludos desde Argentina🇦🇷
Omg, this is unimaginable 😲 excellent💫🌟
Beautiful
Необычный светильник, 😍Хорошее , смелое решение.
Молодец 👍👍👍💖
Большое спасибо Светлана Глазова 😊
This is so cool! I think I might try to follow this video to make something like this for my sister next Christmas
Шикарный светильник, спасибо за мастер класс
You can try to make it. I think everyone can do better than me. If you have any questions, you can leave a message on my channel at any time. 😊
А если перегорят лампочки внутри!?? 🤔
Beautiful as usual
Thanks a lot Ganesh TN 😊
QUITE BEAUTIFUL NIGHT LIGHT
Awesome bro
Very nice
Thanks a lot Nihad Kadhim 😊
روعه ..جميل ..مذهل ..انت مبدع
This was really fun to watch. And a pretty outcome, for sure. Might I make a couple of suggestions?
I know it would be more work, but narration would be MUCH preferred over just music. You're a craftsman. I would love to hear your tips & tricks as you go through some of your steps here.
Also, I'm an electronics guy and I HATE seeing wires splay out from the corner of such a nice piece! One thought would be to make one dowel hollow and route that power wire down through that. Now that wire would sneak almost invisibly out of the bottom of your base and off towards the back.
Anyway, not to nit pick as this was a beautiful piece in its own right. regards, Dan
Good idea
Superb work
Fantastic. The only thing I would try to do is on a future one, have the cord come out near one of the posts and a groove carved in the post so as to “hide” the cord, then come out the bottom of the wood base with a groove so it lays smooth on the bottom and exits to the side. Hope that makes sense - just trying to not have the cord so obvious. In fact, if embedded in a post groove, it could be resined over with a color in the light to mask the cord. Each post could have grooves with resin color - might pick up light from the top and travel a bit into the post.
But no matter - terrific and very imaginative work. Thanks for sharing. Can’t wait to watch more.
Thank you for your advice, I learned more from you rosebudforglory😊
Bello sus trabajos quiero aprender
Fantastic job
Beautiful!!!
عجبتني كيتير جميله 😀👍👍👍
Que belleza ,quiero una!!!!
Muchas gracias Iricel Albarenque 😊
beautiful ❣
Very nice work 👍😎, I like it 😊
Thanks a lot Schwarzer Sternenstaub 😊
Wow amazing
Amazing. It would look even better if you make it round
Thats eleanour rigby in the background music!
The only draw back as I c it, is the lights if they go off, can't be replaced.
WOW! You are amazing.
Ultimate
It's just beautiful 💫💗
Beautiful fairy-forrest...
Thanks a lot Monique B. 😊
Beautiful work thank u for sharing 😍
Awesome ❤️
superb !
Numero 1
👍
Muy hermoso, intentaré hacerlo,mil gracias por compartir 🙏
Muchas gracias Mariela Betancur Ochoa 😊
МАСТЕР 👍👏👏👏💖🌹
Amazing i love it 💖💖
Wauw i love it 😘, i gonna try it , i gonna seal the stands in the Cube i think 👍
Haha, I think you are great, I believe you can do it😜😜
Wundervoll 👍
Bubumop, du bist willkommen, ich bin froh, dass dir meine Harzarbeit gefällt, danke. 😊
Wow the amazing lamp i like it and will try this at home thanks
i love your work. It's too bad I don't have the same tools you do...
I think everyone can do better than me. You can use existing tools to make some simple resin works 😊
Красиво!
Es hermosooo ♡
👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏Me encanta!!!👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏
grabies, de nada, me alegro de que te guste mi trabajo de resina, gracias. 😊
Real 👍🏻⭐️⭐️⭐️⭐️⭐️
Thank you A I. 😊
Hanep! ILike it👍
Thanks a lot Gray minded! 😊
Beautiffuulll 😍😍😍👍👍
Thank you M H Airin. 😊
Wonderful
Thank you Taher Nasser. 😊
@@BuzzingFish 👍🍒😅 really wonderful
Que material son las láminas transparentes y q medidas se usan de resina y endurecedor.
Muchas gracias
Good job! 好漂亮哦！
Thank you Mama Miaw Channel. 😊 谢谢你
SUPER
Thanks a lot Люба Цукерман 😊
i love it :) this is sooooo beautiful
AWESOME!!!!!!!!!
Thanks a lot Melissa McDaniel 😊
Es ist mega schön anzusehen, was mich jedoch stört...warum macht man das kabel nicht durch den standfuß ?
Lo hubieras llenado todo... hasta arriba... te hubieras ahorrado todo ese trabajo de lijar
❤
Awesome work but i cant let those crooked pegs go unnoticed
Haha, It bothers me yet 😊
Great!! Fantastic😵
Thanks you so much 센T멘탈 😊
your works are great.. new subscriber here..
Very pretty. (I think it would have been prettier if you left the twigs out, though. ) ~Great video!
I love it! 💕
Thanks a lot HM Creations 😊
th-cam.com/video/6X95OU9P_EQ/w-d-xo.html
💕💕💕
😍😍😍🙏🙏🙏😘😘😘
tuyệt vòi 👍👍👍
Thank you Gỗ Lũa. 😊
Wow, from the comments you reach a wide Audience.
Thanks a lot Lana Signal 😊
Just as it should be.
th-cam.com/video/vGUBsXrRW9Y/w-d-xo.html Very good
Yes so beautiful
Очень сказочно🥰😘😍 подскажите какая смола у вас для толстых заливок, и как называются эти фонарики на проволочке
Muito bom
man would you please tell me what kind of usb charguer you are using for this work? I really need the info because I used a regular 5volts 1.0 amp and it burned the wired led
Да. классно! Но немного грустно выглядит, я бы веточки покрасила белой краской и приклеила искусственный снег и немного серебряных блёсток. Тогда получился бы зимний светильник :)
вау, твое творчество удивительно 👍
th-cam.com/video/6X95OU9P_EQ/w-d-xo.html
Adorei muito lindo ❤❤❤
Muito obrigado Francineide Justino 😊
👍👍👍💯💯💯💯💯☕
Hermosa!!!!!
Muchas gracias Sara Granje ranje
Wow
Thank you DINU CS. 😊
تجنن مااسم ملمع الخشب هل هو وارنيش
Increíble! Queda preciosa!
Una pregunta, ¿la reacción térmica de tanta resina a la vez no deshace el molde? ¿no se debe aplicar en varias capas? Lo pregunto por que a mi me ha pasado.
Muchas gracias y fantástico trabajo!!!
Después de verter la resina, solo necesita encontrar una manera de enfriarla, como ponerla en el refrigerador o poner cubitos de hielo a su alrededor.
BuzzingFish Fantástico truco, lo probaré! Actualmente lo hago en capas pero se hace eterno 😂
Muchas gracias por el consejo!! 😊
Tengo un problema, las dos veces que he intentado hacer una, el epoxy se ha calentado mucho y me ha quedado el circuito del Led, algún consejo o resina que no coja tanto calor??. Gracias
Si la fiebre es intensa, puede encontrar formas de bajar la temperatura, como poner en el refrigerador, soplar aire o poner un poco de hielo o agua fría fuera del molde.😉
Buonasera... Che resina usi!?
La mia ha un rapporto diverso... 100gr.+60 gr. di indurente... Ma la tua è molto più brillante!!! 👍👍
Puoi inviarmi il link?... Grazie e congratulazioni
Absolutely beautiful, well done !! How do you get your resin / acrylic liquid so clear from the start. No bubbles from the only pour ?
I think he was degassed resin before pour it into mold
😍😍😍😍😍😍
So beautiful :'(
Thank you, don't sad, you are the best, you can do it well ✊
What is the brand of the resin and hardener you used?
Шикарный светильник. А веточки перед заливкой чем нибудь обрабатывали?
Нет лечения, просто убедитесь, что ветви сухие 😊
Hi, what is the thing u used to to make a cube
이뻐요 ^^
고마워요 TV 감성 팔이 😊
Önerebileceğiniz bir reçine markası var mı acaba ayrıca muhteşem bir kanal emeklerinize sağlık teşekkür ederiz
Good night, a question I live in Mexico and I can not find these lights, could you tell me with what name I look for them only in the center LED strips are obviously not used for your beautiful works or they are only sold in your beautiful country as I do my dear friend my name is Adrián Martínez I would appreciate your comments, thank you
I bought this at a hardware store, but there is a led link in the description area below my video
Классно!
Спасибо Самоделки ForestLamp. 😊 Твоя работа тоже отличная
THAT ITS AWESOM :-) Cant u tell which is the mixture you use to make since it is totally unknown to me. It does not exist or does exist in my country, but it is so inaccessible or too expensive, so no one uses it and it is not seen often. Thank you
Que cantidad aproximadamente utiliza de resina epoxi?
حلوو كثير nice
Thank you عمر العلوي Omar AL_aloi. 😊
How did you get the bubbles out? It’s so beautiful and clear.
Very beautiful. I love your job. What is the name of the material you use for molding?
What is the difference using plexiglass and a pre-made square mold?
There is no difference, the plexiglass can be cut according to the size of the work you want to make, and the mold is a fixed size
😊
What are you using for the polish