This was SO helpful! Mine were leaking and I didn’t realize that the sleeve/seat portion came out. I had pulled the spool, but didn’t realize the seats came out. After watching I went back and pulled them both since they were leaking. Im just pissed now that the friggin seal sets are like $80 each for a couple friggin o-rings and seals.
We have a 1845c and the left side will not move at all when we push/pull the joystick. Not sure if it’s the motor for the left side or what. We had to replace wheel bearings and drive chains not long ago. It’s been a major headache. It’s like the lever doesn’t even actuate anything all. The engine doesn’t even bog down like it’s under load. Really hoping it doesn’t need that hyd motor.
Same problem with mine bud.... pretty sure it’s the motor on mine. Swap the hoses over and see if it acts the same. That will confirm motor failure and pump function.
I was replacing the inner and outer sleeve seals. The machine worked fine. It was just leaking hydraulic oil out of the top of the tandem pump drive spool.
hello everyone, i have a problem with my case 1845c, could anyone advise me? When I lift the whole loader arm with a spoon, empty or full, it doesn't matter, it lifts up well, but down it goes very very slowly. It always jumps a little up when starting. The spoon can be opened and closed well. When I turn off the engine the loader arm goes down well. If I go down and at the same time open and close the spoon it goes a little lower it faster. Even if the loader arm does not move, the hydraulics sound as if they are hissing, as if the hydraulics are working. At the same time, the right side of the wheel control does not work properly. Please advise what the problem is. The hydraulic fluid is full. Thanks for the reply
I know this is an old video but if it leaks bad what happens...just a mess or does it affect the way it runs.. elaborate if someone could for me.I have one it leaks going to replace it but what did it do..mine warms up it becomes sluggish like it's leaking somewhere can only control one thing at a time not pushing force...leaks pretty bad on the top there..just curious
I've got a grey cab Case 1840. I have the same problem BUT can't find any seals. Can you help me find the parts I need to do this for my machine ? Id like to go a head a replace the sleeve, seals and drive spool seals too.
wow thank u so much i have one guy mechanic gut told me i have to rebuild this pump and he took 1.000$ and he just replace this what u do and nothing else Shame on him and we have Karma they will get back what he deserve and why stealing money from people Thank u body i have case 1840
This was SO helpful! Mine were leaking and I didn’t realize that the sleeve/seat portion came out. I had pulled the spool, but didn’t realize the seats came out. After watching I went back and pulled them both since they were leaking. Im just pissed now that the friggin seal sets are like $80 each for a couple friggin o-rings and seals.
Excellent instructional VIDEO. Thanks for valuable time. Keep up the video on the 1845C.
We have a 1845c and the left side will not move at all when we push/pull the joystick. Not sure if it’s the motor for the left side or what. We had to replace wheel bearings and drive chains not long ago. It’s been a major headache. It’s like the lever doesn’t even actuate anything all. The engine doesn’t even bog down like it’s under load. Really hoping it doesn’t need that hyd motor.
Same problem with mine bud.... pretty sure it’s the motor on mine. Swap the hoses over and see if it acts the same. That will confirm motor failure and pump function.
Hello. Have you resolved this issue?
I have the same problem in 1845b the left lever is loose and the left side responds poorly
@@michakoralewski2622 sadly no, life has gotten in the way and the project is on hold.
You can provide the stamp kit series please
What was it doing to make a replace that part? I have 1 that's not going backwards or forward
I was replacing the inner and outer sleeve seals. The machine worked fine. It was just leaking hydraulic oil out of the top of the tandem pump drive spool.
did you find out what was wrong? a friend has the same problem
Thanks for posting!
Phil, did you have to drain the hyd. oil first. I tried to remove mine and oil ran out
Yes, you have to drain the hydraulic oil first unfortunately.
@@phillambos im about to do this to my 1835c, did you have to drain the fluid from just the tandem pump? or the whole machine?
any one can help pleas my 1845 skid steer making grinding sound when turning
hello everyone, i have a problem with my case 1845c, could anyone advise me? When I lift the whole loader arm with a spoon, empty or full, it doesn't matter, it lifts up well, but down it goes very very slowly. It always jumps a little up when starting. The spoon can be opened and closed well. When I turn off the engine the loader arm goes down well. If I go down and at the same time open and close the spoon it goes a little lower it faster. Even if the loader arm does not move, the hydraulics sound as if they are hissing, as if the hydraulics are working. At the same time, the right side of the wheel control does not work properly. Please advise what the problem is. The hydraulic fluid is full. Thanks for the reply
I know this is an old video but if it leaks bad what happens...just a mess or does it affect the way it runs.. elaborate if someone could for me.I have one it leaks going to replace it but what did it do..mine warms up it becomes sluggish like it's leaking somewhere can only control one thing at a time not pushing force...leaks pretty bad on the top there..just curious
what are the symptoms of bad drive oil seals
bad drive spool seals don't cause a problem. They just leak hydraulic oil and create a mess inside the machine.
I've got a grey cab Case 1840. I have the same problem BUT can't find any seals. Can you help me find the parts I need to do this for my machine ? Id like to go a head a replace the sleeve, seals and drive spool seals too.
Part #'s here: th-cam.com/video/A7Dh6PR_vQs/w-d-xo.html
Where did you get the seal kit? And do you know the case part number?
Case #'s here: th-cam.com/video/A7Dh6PR_vQs/w-d-xo.html
wow thank u so much
i have one guy mechanic gut told me i have to rebuild this pump and he took 1.000$ and he just replace this what u do and nothing else
Shame on him and we have Karma they will get back what he deserve and why stealing money from people
Thank u body
i have case 1840
تعمیر پمپ بگو کامل ممنون
Hola alguien me puede ayudar tengo una case 1840 que cuando lleva un tiempo de trabajo deja de caminar para delante solo un lado
786sk