Making a staple, pinning the plug, and carving a spout stopper | DIY black powder accoutrements
ฝัง
- เผยแพร่เมื่อ 29 มิ.ย. 2024
- ➽ ➽ Support the channel - nmlra.org/join ➽ ➽
Sign up for traditional craft classes taught by master artisans at NMLRA.org/education
In part 2 of this basic powder horn construction series, we head to the blacksmith shop to forge a "staple" to hook our horn to our hunting pouch, pin our plug to the horn, and create a plug for our horn spout
0:00 Introduction
0:03 My simple forge
0:23 If you don't have a forge - Supplies
0:46 Staple layout
1:36 Staple mockup
3:04 Forging the staple
4:48 Setting the staple
6:09 About pinning
7:28 Pinning the plug
13:16 Carving the spout plug
14:12 The completed horn
Visit hornguild.org to find out more about working with horn
Throughout this series, you will learn how to make your own simple powder horn from start to finish. Techniques used include but are not limited to filing, scraping, woodcarving, blacksmithing, metalworking, whittling, leatherworking, scrimshaw, and more.
Find your powder Horn and traditional craft supplies at nmlra.org/shop-small and NMLRA.org/advertisers
Tremont Cut Nails - [www.tremontnail.com/]
Build this project at your own risk, this video is not a substitute for reading the safety guidelines for your tools and materials.
➽ ➽ Muzzle Loading & Living History Books, Merch, and More - nmlra.org/store ➽ ➽
The NMLRA exists to promote, support, nurture, and preserve our nation’s rich historical heritage in the sport of muzzleloading through recreational, educational, and historical venues.
Since 1933, we have led the effort to preserve the history of the United States through muzzleloading shooting sports & living history events.
Website: NMLRA.org
Podcast: NMLRA.org/podcast
Instagram: muzzleblasts
Facebook: NMLRA
Facebook Group: groups/NMLRA
Good video. I enjoyed it a lot. Want to save yourself a little aggravation? I noticed your base seemed to be slightly tapered from the inside of the horn to the outside. That's good. When you get close boil the base of the horn in water. That will soften it and you will be able to drive the base into the horn. The horn will shrink and you won't have any of those open gaps to worry about and you won't need the epoxy. I made a horn like that 40 years ago and it's never leaked and my powder has never gotten damp. I made my staple pretty much the same way as you did. I pinned the base into the horn the same way too, except I used whittled wooden pegs instead of nails.
A hand forged staple 😁👍👏 very nice and now you will need a hand woven strap 😁😊
In place of a staple I always used a large threaded plug to which the strap is attached. The plug works to unscrew and insert powder into the horn.
Lookin Good
Nice looking horn , you did a fine job .
Coming along real nice, something to be proud of, heirloom.
For drilling pin holes.
Tape around horn base.
Measure around horn base and decide how far apart pins need to be so they are even
(Example, measurement around was 7.5 inches, pins look good to me at 3/4 an inch intervals, so I mark then drill 10 holes at 3/4 inch intervals).
Remove tape, put pins in holes....
I would have used the head end of the nails, cut nails look great and add legitimacy to replicas of older items...
Nice looking horn.
Thanks for this video
Nice job
I enjoyed the video. Thank you, Sir!
This is great!@
At your final point, which is nice, you could order a brass measuring spout to fit right to the horn.
Ok, non muzzle loader here (yet). Since you've glued, and pinned the plug into the horn. How much of a chore is it to fill the horn with powder through the spout?
CA: It's not a 'chore". But it probably takes perhaps five minutes or so. Remember, this sn't modern high speed warfare, and the frontier man carrying this rifle isn't going into combat.
Another simple way of making a staple is to use a romex (electrical wire) staple. You can buy them at Lowe’s, Home Depot, and most hardware stores. I heat them up with a simple propane or map gas torch, twist it 360 deg. and dip it in motor oil and it comes out looking old and forged. Your comiting blasphemy again, they didn’t have 5 minute epoxy back then. Of course they didn’t romex staples either, so I guess I’m just as guilty😬
ID raise the staple toward the upper part of the horn so as to balance it better let the weight drag the horn down Staple on the upper part of the but plate!
I like the way that you did this horn and I have a problem non 2 horns that I have one is for a powder horn that I want to make and the other is for one that I bought. The one that I bought is supposed to be fully functional with a powder measure spout on it but it does not seem water tight and when I blow thrue the spout with the valve open it leaked air from the plug end. Slightly how so I make this water tight or is it supposed to do so? And the one t h at I am making the open end where the plug goes needs to be cut square for the plug. What should I use or can I use a Drexel tool also I would like to make a wood screw plug. ccin the plug for filling the horn with powder how do I do this. I am an avid outdoors man Ang getting back into black powder hunting and want to make a lot of my own tools and horn for this I have a kit that I purchased for a rifle and am making my own shooting bag. I don't mind cheating on somethings and go with modern materials for some things but want my horns to be fully functional and keep my powder dry how do I seal them properly? Also what is the best wood to use for the plunge both at the spout and bottom end
But yes good video
How do you fill it?
I have the same question. funnell?
The whole idea of “ handmade”, at least in my opinion, is yours won’t look exactly like every one else’s. Individualism is important. If everyone looked exactly alike they would look more like soldiers than mountain men. It was a good winter job for them when they were waiting for the greenup.
I think you should have rounded your staple so it doesn't cut your shoulder strap.
Do you have a source for the nails you used
Thanks
Instead of the little wood plug take the end you cut of and drill a whole and put a wood rod in it just a little better looking
Gosh darn that's smart.
Птица Говорун.
I got a Antique coal forge & 3 Antique Anvils for sale or trade!!!!!!
Martin Corbitt what's the price and where do you live?
@@r.a.facklam4851 I live close to Douglas, Ga. I love to trade things or cash. There are 150 , 107, & 75 or close . A real nice turn of the century coal forge with complete blower. If cash make me and offer!
@@martincorbitt1979 sorry, I guess I'm not interested, I live in northern Wisconsin.
@@r.a.facklam4851 they are different size anvils. The antique coal gorge is 450.
@@r.a.facklam4851 I live in Doulas,Ga
5 minute Epoxy is not period correct, try some Pine Pitch.
And Brass / copper were easier to work back in the day so it was more likely to be used by the common man.
The propane he used to heat it is not period correct either, nor the artificial light. Get a life.