Hey Danny, 1st of all thanks for sharing this video. I have a 2006 Murano which died in the middle of the highway on my wife the other day. I couldn't figure it out it went into limp mode driving about 5-7 mph. She cruised it to the shoulder and we had it towed home. Fast forward to today after testing it out again it was still going into limp mode. I'm watching a number of vids related. Your video saved me a lot of work. My brake and ABS lights were flashing. I checked my fluids and the psf was low. I added atf to the reservoir and all the lights when of and it started driving normally again. Thanks a million man
Had to comment to say thank you. Coolant level was extremely low in my car, never realized it. Filled it up, cleared the "camshaft" code, running great ever since.
it’s nice when it’s just something simple! My father in law took our car in without me knowing since the lights came on and the dealership wanted $75 to add some power steering fluid! I told them no, added some and was on my way.
Life saver! I got the slip, abs and vdc off lights on my 03 coupe after trying to skirt skirt. I added some coolant because i was basically empty and that did the trick! Thank you!!
Thanks! My 2008 pathfinder stalled after making a left turn. I restarted and noticed VDC and Slip came on at the same time. Watched this video and then checked my fluids. My Power Steering was at min level so I added power steering fluid. I then disconnected battery for 10 minutes to reset computer and voila problem has gone away! Thanks again !!
Also check your ABS sensor on your rear differential it can wiggle out and throw all three lights. Or you can just take the sensor out of its spot if you want the lights to come on
Thanks so much for your video! My 2006 Infiniti G35 just did that on me. I had to remove the battery cable to save power. I plan to take to the shop this weekend but it seems like I what did would reset the sensors. Again! Your video is a real life saver for me!
Wait so let me understand this.. this isnt fixing your car its just patching it for a couple weeks? Does this method still work and how long do the VDC Lights and stuff stay on for? Would this also work buy using a diagnostic device and deleting the codes.
It is just resetting the system later on driving it will pop up again. This does not fix, it’s a common problem with the Infiniti’s, it is a sensor issue that without it it takes off ur ABS VDC slip and another one I can’t remember.. change the sensor if u want ann bc permanent fix.. another one is the gally gasket in the engine behind the timing belt.. big job, but a common problem for g37s, the factory gasket was a defect n most engines will be leaking out from that gasket.. if u change all that it’s like a new car again.. hope this helps someone...
I am the original owner of a 2004 armada, I would usually get the ABS effect when I had done a jump start to another vehicle, but lately I have been getting a brake light indicator on the dash then VDC and slip lights would turn on and then later get the ABS effect. I checked all three fluids and they were within ranges. I decided to add brake fluid to the max line and this has stopped my issues. I too had watched other you tubers saying they replaced the brake booster or the ABS module with no benefit. Thanks for placing this video on yt
I'm 3 for 3 on this procedure. It works GREAT! Thanks for the video. I have a 2005 Infiniti G35 manual transmission sedan. This has happened 3 or 4 times in the last couple of months. In at least two cases, lights came on after hitting a speed bump. Today, I didn't even bother to disconnect the battery. I just started the engine, did a sharp left hand circle. Pump stopped but lights still on. Turned off the car. Started it, did the left turn again and lights cleared. Tested the VDC control button and it functions on/off again. Fluid levels look OK but I'm going to top them off to see if things improve.
@@scottyscott1898 I never got around to it yet, but things have been fine for the last 2 weeks. It's only a matter of time before it does it again. The majority of threads point to the relay as the issue. It's just an expensive gamble. For now I'll keep doing the occasional cheap reset until it gets too frequent. I need to do the control arm bushings, so I'll look for a loose sensor or wiring. Seems odd that every time it happens corresponds to hitting a speed bump.
Thanks bro was looking for this everywhere for a easy quick basic fix or an idea on what to do you were the only video!!!! thank you keep up the great work
I usually get rid of the lights and the buzzing by putting it into neutral while driving 10+ mph and shutting the car off and starting it again- yes while driving. It’s a little sketch but it works every time. My car just needs a new abs module.
I've been dealing with this on my 2005 G35 Coupe 6mt under 70k miles. Having found a few videos and tips on G35 forums... I have seen people talk about 1. low fluid levels (no for me) 2. rusted or impaired sensor contaminates on the brakes (not sure), 3. Fix- High G maneuvers to trigger the ABS to reset. I've had success after 2-6 times going at idle at 5-10 mph (with no one behind me) and SLAMMING ON THE BRAKES and having it skid (no ABS) to a stop. Luckily, I live in a place with lots of empty streets and stop signs... (I've heard of people going to parking lots and doing a hard turn plus the stomping on the brakes) to get the high G's. I've also heard of guys going backwards and slamming on the brakes.). Some guys even take a pair of pliers and hit the ABS humming motor if not shut off will kill your battery and itself - if you can't stop it when you shut off the car and it keeps going. Back up solutions - pull the ABS circuit breaker next to the battery... and or disconnect the battery - that will then continue to screw itself when re-connected the next day itself unless you get it to reset. This is pissing me off now... as I need a car to work and not drive around like a drunk slamming on my brakes, screeching to a stop, turn off and on, and hope it resets... today was 6 times... slick parking garages don't work as well. You really need the hood to dive at taxing speed or 5-10mph... full stop for it to reset. Grrr... If this continues it is time for a dealer to screw me or an semi-competent Shell dealer as there are multiple possible solutions.
Yeah, they are triggered easy for anything with a sensor or fluid level. Mine turned off with the circle technique th-cam.com/video/L8S0MjvGP3I/w-d-xo.html
I have a 2006 G35X and the Slip, VCD Off and Brake lights all came on this morning. I read it can be as simple as being the car needs break fluid to worn break pads etc. I had mine towed to a trustworthy mechanic and hopefully I’ll have it back in a few days. Cars are fun...until they start things like this.
Low Battery and or "Low brake fluid" Fixed both. Than did the braking technique. Both Light's turned off after doing the braking technique while I was driving. "Sweet" Thanks.
This worked for my 2008 infiniti g35x. Thanks a lot was worried about these lights for a few months but thanks to u problem was fixed. Low break fluid. Saved me lots of money This guys the 🐐🐐🐐🐐🐐
Hey the light is flashing it means you have a tire low Make sure your 4 tires are at 35 psi It can make all that lights come on That happened on my car One of my tire was low on air I put 35 psi I turn off the car then turn on and not more lights!
Dear Danny Johnson, I had the exact problem shown in your above video. Fluid levels were all OK. I disconnected the battery negative and that did the trick! Very good outcome! I had to reset some electronics inside the car, like the radio, electric seats, etc... No big deal. Thanks a bunch. :)
@@dannyjohnsonsgarage Hi Danng! My name is Luis Urbieta and I have a question. What dos VDC and ABS stand for? Love how you explained what you have to do and we have a Nissan Centra that does that. Please answer my comment when you can. Thanks.
U saved me literally i got to work and the abs started running the test and i turned off the car and that noise came on i did what u said and it worked
I’ve had the same thing happened to me several times. Went with intuition once I learned where the noise was coming from and figured out a method that actually works ever time! Whenever I hear that sound and see all the lights come on, I quickly find a spot to pull over and turn my car off. I pump the brakes a few times and then start my car and put it in reverse. I drive back about 10 feet or so and then put it in drive and either drive to wherever I’m going or I will drive forward for a little bit and then stop and turn off my car again. Once you’ve done that and turned it back on, the sound will go away but the lights will stay on for a few minutes. If it doesn’t work, try it again. If it’s still on, you might need to look into it. Hope this helps you guys!
Good advice. Essentially you are having the car run an abs test. This is the concept for driving in a circle or starting the car and driving off. You’ll hear the psssssh sound as it tests.
Thanks Danny that really helped. I have a 2008 Skyline with that problem. So thank you very much. And ironically my name is Daniel and they call me Danny too.👊🏽👍🏾
I dont have that humming noise but ill try this later... I have had all these 3 lights the past 2 years lol... Car is running fine but of ocurse no traction control or ABS...
You’re the man! Thank you. I recently replaced camshaft sensor b1 on 2008 fx 35. Since then vdc, slip lights won’t turn off and its been stalling in motion. Added some coolant and battery was unplugged for 10+ minutes. Should be good now. Do you have recommendation on fuel saving? Recently changed both air filters and where am I is extremely cold with traffic jam. Do you recommend fuel injector cleaning additive?
I would only suggest adding some sea foam to the gas tank only (one gallon of gas for each ounce, so you’ll want to put it in when filling the tank). Otherwise, use the cruise control when you are driving steady and that’s the best milage you’ll get. It does make a difference
My 06 G35 does this sometimes. I just pull over and park, turn the car off and back on, put it in reverse and go about 15 feet and stop and the humming sound stops but the lights stay on until I turn the car back off and on again, I never have to disconnect the battery. Thanks for the video.
After turning my car on and off G35 2005 6mt, I backed out to drive it to Shell station (having not read your post). I decided one last time to turn it on/off and it worked like you said - I drove it back and parked it. I will find out tonight if it works. Thanks!
I tried to do this and it came back on so many times...I have had a problem for a year and a half and taken my car to several mechanics.... and had to do a manual reset everytime before I start the car just for me to figure out it was a position sensor...the position sensor fixed my problem and I can start my car like normal again
If the tire is full it’s most likely the sensor that is battery operated. The battery will die and it’s part of the valve stem so you have to remove the tire th-cam.com/video/nUNDvEzUjhI/w-d-xo.html
It just happened to mine this morning, didn't disconnect anything , mine is 2006 auto coupe , I just switched transmission (D) to tiptronic (manual) and they all disappeared at once lol
Great video. I started with checking fluids. My power steering was a little less than half full. Topped it off and it’s all good now. If it comes back on, I’ll try disconnecting the battery. I don’t know if it’s related but after VDC and Slip came on, I got a flashing air bag light. I found another video how to fix that and it worked. I have a 2008 Nissan Pathfinder so at this point it’s a 13 year old vehicle. It’s just gonna have issues. Luckily TH-cam helped me fix box of them. Great video!
My sparkplugs and coils were just replaced after that went home when I made turn car turned off engin light came on and all other lights did what your. Video showed lights came off but it still turned off as I'm driving
Abs relay . You need the codes scanned. What he did is just a system test and reset . It's not a fix. You need a scanner that reads abs codes. Just repaired mine and it was the abs relay
Thanks! Had 2 out of 3, low brake fluid & power steering. Topped off both and lights went out. I'm sure the Stealership would have told me I need to replace all bearings and ABS sensors for $1,200.
TOMCAT631 They wanted $80 for less than one ounce of brake fluid for the power steering- after I told them eagan was wrong (my father in law took our car in without us knowing when he borrowed it).
Vehicle dynamic control VDC means traction control. It’s automatically on when you drive, which helps the car with stability. Turning it off when you push the button is disabling it and now you’re in manual mode as if the car did not have any kind of traction control. Some vdc systems can apply the brakes on only one wheel to straighten the car out.
i have infiniti g35 and have this problem and your video helped but now my battery and brake light is on I changed the alternator and battery and its still on.
The brake light should just be some slack in the cable and the battery light (and the brake light) may just be coming on like mine do. Try gently pushing up on the gauge cluster visor hood and see if the lights turn off. Mine turn off when I lift on the gauge cluster visor
I got an M45 with the slip and engine light on. I’m going to top all the fluids and disconnect the negative battery terminal to see if that clears them because right now it’s in fail safe mode.
@@dannyjohnsonsgarage I’ve seen the speed sensor on auto zones site for like $25. That may be the culprit, if so I’ll do that but I do need the diag check, I tried checking the diag through the menu and it couldn’t complete it because their was a malfunction
I have a 2007 Infiniti fx35 and my mph just stopped working then the abs and slip light came on then I turned my car off and it went off but my mph still doesn’t work any suggestions?
So I have a 2005 6MT g35 and those three lights come on randomly as I drive the car and once I turn off the car, I hear the buzzing you talk about and I have to try and get the car to re-test the abs system by restarting it and driving a little then maybe the buzzing will go away. My fluids are all topped off but I do have 2 different codes coming up. I have one for an O2 sensor and another for the pnp switch. I changed the pnp switch but the code still comes up
I would start with the codes and get the 02 replaced, but if you are hearing the buzzing, it sounds like it’s the abs module/pump. You can try gently tapping on it, but if it just won’t go away it may need to be replaced
I have the same issue with my 2005 pathfinder. Took it to Nissan and they told me there was a circuit break on the left rear speed sensor. I replaced the sensor twice and still giving same error. My ABS/VD/SLIP and now my 4WD and Brake light is on. WTF.. Dealer want to replace my wiring setup for $1500... And it's not even a guarantee to fix the problem. I'll try checking the fluids and disconnecting battery when I get home. I need the 4x here in Wisconsin.
just got scammed out of a g35 and this slip light comes on and will limit power ( ABS , VDC OFF) are both staying on and the slip warning will flash when i drive sometimes
I have an m35x and while I'm driving it would shut off and those lights will come on after a few minutes it will start back up can I have the same problem
I have a Nissan Altima and it showed these three specific lights on the board. I was driving and I almost freaked out and it also did that humming noise. Then I turned the car on again and they were gone.
About to try this now.power steering fluid is right under minimum line.oil was crazy low (sons car), hopefully that fixes it.it also randomly stalls and drains battery.🤦
THANK YOU. GOING TO CHECK MY 2012 SRX - WHICH ABS AND STABILITRAK ARE BEING ON FOR A WHILE. AND A NOISE IS COMING FROM ON THE FRONT OF THE CAR LIKE SOMETHING IS RUBBING AGAINST SOMETHING. I JUST REPLACE THE ROTORS AND BREAK PADS ON THE FRONT, INCLUDING THE DRIVER SIDE WHEEL BEARING. I STILL HEAR THE NOISE AND SOMETIMES WHEN I BREAK IS LIKE A THE BREAKS ARE SKIPPING. I THINK I GOT AIR ON THE BREAK LINE.
Question random shutdown and trouble starting here and there. Same lights. 06 m35x infinity Changed crack shaft sensor no go. Cam shaft sensors next? Sez there is a left and a right one.
Question, When the slip and vdc lights go off on my daughters infinity m35x goes off there’s like a hesitation and scraping sound coming from the drivers side of the car. Things that have been replaced Axel(2) Drive shaft Carrier assembly Note: the vdc & slip light came on after this work. ANY insight would be very helpful
My 2007 m35 does this but sometimes while I’m driving the car turns off , I believe it can be my harness is damaged because I had to replace the fuse connecters to the battery terminal
thanks for sharing sir,i have a 2015 quest and after that freezing temperature here in chicago that light and brake light would come on on cold days,in the summer it would not..i have to try what you did..thanks so much
Hey Danny I hope to hear from you soon for I am stuck In a hard spot. This wouldn't be so hard if I had access to a code scanner but i do not.. none of my neighbors have one and I am almost an hour away from the nearest shop with the broken vehicle being my only one at the moment. My wife had the 03 Infiniti G35 at work and she called me saying there was a VDC, Slip & At Check and check engine light and the oil light was on. All the resivors were about half full and the oil maybe needed half a quart if that. The blinkers, taillights and the head lights (50%) of the time do not work. The car does not run very good cant make it to work until it's fixed. My neighbor is running me to advance 1 time get parts. If it's not fixed or I guess wrong im fuced. My final guess before I go is cam shaft sensor. Let me know what you think
Ok Danny just watched video today and you gave great info....but what you think the problem is if it's not starting back up. The security red light is not on and the key will not turn
For me I have an 07 6mt coupe g35 and the car just jerked and my check engine ,slip and vdc light came on i shut the car off i turned it back on all lights were still on later that day i disconnected the battery from the car and waited 10 min i connected it back and the check all lights went away but as i drove off the car jerked again and my vdc and slip light came on and to this day after i drive a few feet to the left the lights will come on
The lights all come on for any sensor or fluid level, so it could be from a throttle position sensor, crank position sensor, low fluid levels...you’ll have to find out which one is causing it. If you can get a code reader it may be able to tell you
My VDC, ABS, Slip and Brake lights in my Pathfinder come on when I reach 16mph, at the same time the doors auto lock. This started one day after I "slipped" at a red light on the wet street. I will make sure my fluid levels are ok but I am thinking its just a malfunction. Years ago in my Maxima my factory premium radio and CD player stopped working. I refused to replace it. It was rough. LOL!! About a month in when I actually was about to break down and buy something new, it just began working again flawlessly.
Misalignment or incorrect tire size from wear or wrong XXX/65/20 for example i had a VDC and ABS light come on... when i mis aligned my wheels... (rear). I realigned my wheels and the ABS system no longer noticed wheel ratios turning at different speeds... its most likely, incorrect tires/worn tires/ incorrect wheel alignment .. .or last a level suspension indicator(little plastic arm) is broken or popped off the frame.
Hi Danny. I have the same problem with my 2005 G35x. Big problem is the ABS pump keeps going even with the engine shut off, and after about 1 hour the battery has run down so car won't start Any idea what causes this problem in the first place? I have to disconnect the battery when I park the car or it won't start when I want to drive it. This is a real pain in the ass. I have a few ideas that I will try tomorrow.
My 05g35 is doing the exact same thing. I heard the abs module running the other day and disconnected the battery to stop it and i guess reset it. I didn't hear it in the thunderstorm last night and car was dead as hell this morning UGGHHHH... did you figure out why the abs module would constantly run all night with the key off? ?????
I hit a pot hole hard once and all the lights came on and then it came off after making like 3 runs with my car to places and I guess I went over “rumble” speed bump regular speed and these lights came on again and it’s annoying to me. I haven’t made any runs anywhere so I wanted to see if I can get these lights off by pressing somthing on my 08 Infiniti G35x…I guess I’ll just wait till they go off on it’s own like last time.
I have a 05 Nissan psthfinder both lights are on so we unhooked the battery cable for like 20 minutes they arevdtill on so im going to find a place where I can drive 20 mph. Fir about 15 minutes and the stop and turn it off and then start it up again. I can t afford to put any more money in it
Please help...is this what I need to do I am a woman ive put new breaks all around new tires all around new rotors all around and the front end lined up. Right St 1700.00 bucks not counting what I paid fir it
![[UNCUT]"ตุลามรณะ"ย้อนฟังคำทำนาย หมอดูทุกสาย ดวงเมืองร้อน (หมอปลาย ฟองสนาน อ.โอเล่)I คนดังนั่งเคลียร์](http://i.ytimg.com/vi/lE5az5VvT9M/mqdefault.jpg)
I have a 2010 Infinity QX56. I tried these steps today and it actually worked. All of my lights went out. Thanks for sharing.
Hey Danny, 1st of all thanks for sharing this video. I have a 2006 Murano which died in the middle of the highway on my wife the other day. I couldn't figure it out it went into limp mode driving about 5-7 mph. She cruised it to the shoulder and we had it towed home. Fast forward to today after testing it out again it was still going into limp mode. I'm watching a number of vids related. Your video saved me a lot of work. My brake and ABS lights were flashing. I checked my fluids and the psf was low. I added atf to the reservoir and all the lights when of and it started driving normally again.
Thanks a million man
So glad you found the video! Thanks for watching
Having the same problem in my infinity g35 you added power steering and what else?
Had to comment to say thank you. Coolant level was extremely low in my car, never realized it. Filled it up, cleared the "camshaft" code, running great ever since.
it’s nice when it’s just something simple! My father in law took our car in without me knowing since the lights came on and the dealership wanted $75 to add some power steering fluid! I told them no, added some and was on my way.
Life saver! I got the slip, abs and vdc off lights on my 03 coupe after trying to skirt skirt. I added some coolant because i was basically empty and that did the trick! Thank you!!
How long did it take for the lights to disappear?
Yes how til it disappeared?
@@aaronpruitt5814 Disconnect battery! Wait 5-10 minutes.
Thanks! My 2008 pathfinder stalled after making a left turn. I restarted and noticed VDC and Slip came on at the same time. Watched this video and then checked my fluids. My Power Steering was at min level so I added power steering fluid. I then disconnected battery for 10 minutes to reset computer and voila problem has gone away! Thanks again !!
Glad it helped! Many things can trigger it. Kind of annoying lol. But at least it makes us verify things are safe
I bet it was the crankshaft sensor or cam sensor lol i had to replace both of those with my pathfinder.
Also check your ABS sensor on your rear differential it can wiggle out and throw all three lights. Or you can just take the sensor out of its spot if you want the lights to come on
Thanks so much for your video! My 2006 Infiniti G35 just did that on me. I had to remove the battery cable to save power. I plan to take to the shop this weekend but it seems like I what did would reset the sensors. Again! Your video is a real life saver for me!
I’m glad to hear that it was useful. Good luck- as you see it can be a number of things
Wait so let me understand this.. this isnt fixing your car its just patching it for a couple weeks? Does this method still work and how long do the VDC Lights and stuff stay on for? Would this also work buy using a diagnostic device and deleting the codes.
It is just resetting the system later on driving it will pop up again. This does not fix, it’s a common problem with the Infiniti’s, it is a sensor issue that without it it takes off ur ABS VDC slip and another one I can’t remember.. change the sensor if u want ann bc permanent fix.. another one is the gally gasket in the engine behind the timing belt.. big job, but a common problem for g37s, the factory gasket was a defect n most engines will be leaking out from that gasket.. if u change all that it’s like a new car again.. hope this helps someone...
Hi everyone my Nissan Murano 2006 it's on ABS ,VDC,Also slip light on I need to turn off please
@@xxxko4532 abs relay
I am the original owner of a 2004 armada, I would usually get the ABS effect when I had done a jump start to another vehicle, but lately I have been getting a brake light indicator on the dash then VDC and slip lights would turn on and then later get the ABS effect. I checked all three fluids and they were within ranges. I decided to add brake fluid to the max line and this has stopped my issues. I too had watched other you tubers saying they replaced the brake booster or the ABS module with no benefit. Thanks for placing this video on yt
I'm 3 for 3 on this procedure. It works GREAT! Thanks for the video.
I have a 2005 Infiniti G35 manual transmission sedan. This has happened 3 or 4 times in the last couple of months. In at least two cases, lights came on after hitting a speed bump. Today, I didn't even bother to disconnect the battery. I just started the engine, did a sharp left hand circle. Pump stopped but lights still on. Turned off the car. Started it, did the left turn again and lights cleared. Tested the VDC control button and it functions on/off again. Fluid levels look OK but I'm going to top them off to see if things improve.
Arctic Minibike so, how did it work? Everything back to normal with topped off fluid levels?
@@scottyscott1898 I never got around to it yet, but things have been fine for the last 2 weeks. It's only a matter of time before it does it again. The majority of threads point to the relay as the issue. It's just an expensive gamble. For now I'll keep doing the occasional cheap reset until it gets too frequent. I need to do the control arm bushings, so I'll look for a loose sensor or wiring. Seems odd that every time it happens corresponds to hitting a speed bump.
@@arcticminibike4033 definitely the abs relay . I replaced mine today with 1 from the junkyard it was 10 bucks compared to 220 new
Thanks bro was looking for this everywhere for a easy quick basic fix or an idea on what to do you were the only video!!!! thank you keep up the great work
Have had my car 15 years and always wondered what that “fart” sound was…ABS system testing. Thanks
FACTS
my 350Z is doing the same thing, I will try those tomorrow
I usually get rid of the lights and the buzzing by putting it into neutral while driving 10+ mph and shutting the car off and starting it again- yes while driving. It’s a little sketch but it works every time. My car just needs a new abs module.
I've been dealing with this on my 2005 G35 Coupe 6mt under 70k miles. Having found a few videos and tips on G35 forums... I have seen people talk about 1. low fluid levels (no for me) 2. rusted or impaired sensor contaminates on the brakes (not sure), 3. Fix- High G maneuvers to trigger the ABS to reset. I've had success after 2-6 times going at idle at 5-10 mph (with no one behind me) and SLAMMING ON THE BRAKES and having it skid (no ABS) to a stop. Luckily, I live in a place with lots of empty streets and stop signs... (I've heard of people going to parking lots and doing a hard turn plus the stomping on the brakes) to get the high G's. I've also heard of guys going backwards and slamming on the brakes.). Some guys even take a pair of pliers and hit the ABS humming motor if not shut off will kill your battery and itself - if you can't stop it when you shut off the car and it keeps going. Back up solutions - pull the ABS circuit breaker next to the battery... and or disconnect the battery - that will then continue to screw itself when re-connected the next day itself unless you get it to reset. This is pissing me off now... as I need a car to work and not drive around like a drunk slamming on my brakes, screeching to a stop, turn off and on, and hope it resets... today was 6 times... slick parking garages don't work as well. You really need the hood to dive at taxing speed or 5-10mph... full stop for it to reset. Grrr... If this continues it is time for a dealer to screw me or an semi-competent Shell dealer as there are multiple possible solutions.
Yeah, they are triggered easy for anything with a sensor or fluid level. Mine turned off with the circle technique th-cam.com/video/L8S0MjvGP3I/w-d-xo.html
I have a 2006 G35X and the Slip, VCD Off and Brake lights all came on this morning. I read it can be as simple as being the car needs break fluid to worn break pads etc. I had mine towed to a trustworthy mechanic and hopefully I’ll have it back in a few days. Cars are fun...until they start things like this.
What was the issue? My g35x is doing it rn
OMG JUST GOT A 05 & THOUGHT MOTOR WAS SLIPPING SOON😂😂😂😂THANKKKK YOUUUU!
🤣🤣😂😂🤣😂🤣😂🤣🤣🤣😂😂😂🤣🤪 me tooo I’m like ooh lard not so soon the transmission or engine slipping 🤣🤣🤣🤣😂😂
@@phenomenaljone ++p 0po0
@@phenomenaljone ++p 0po0
🤣🤣🤣🤣🤣
@phenomenaljone
Low Battery and or "Low brake fluid" Fixed both. Than did the braking technique. Both Light's turned off after doing the braking technique while I was driving. "Sweet" Thanks.
what is the breaking technique?
@@theotf4lifemgtteam450 You brake while turning a sharp turn than drive straight.
Stacy the Rooster its ok i fixed it witout needing to do any of this lol
Thank you so much! It happend as soon as I got home from work while driving in the rain thanks for the explanation I was able to turn of the lights
Thanks mind started wondering hard, gave me a sign relief and that’s exactly what it was piece broke off
Check your brake lights. The fuse (10 amp) was blown causing the safety feature to lock the transmission.
E Gonzalez That’s crazy!
The heck!
Wheres all those fuses at? Under the hood? I drive a 03 g35
@@red_day6097 They're behind the driver's side kick panel to the left of the foot pedals.
I love this car and the battery disconnect advice is fantastic....
This worked for my 2008 infiniti g35x. Thanks a lot was worried about these lights for a few months but thanks to u problem was fixed. Low break fluid. Saved me lots of money
This guys the 🐐🐐🐐🐐🐐
Hey the light is flashing it means you have a tire low
Make sure your 4 tires are at 35 psi
It can make all that lights come on
That happened on my car
One of my tire was low on air
I put 35 psi I turn off the car then turn on and not more lights!
Omg thanks I always heard that weird sound now I k ow its just the abs test
Dear Danny Johnson, I had the exact problem shown in your above video. Fluid levels were all OK. I disconnected the battery negative and that did the trick! Very good outcome! I had to reset some electronics inside the car, like the radio, electric seats, etc... No big deal. Thanks a bunch. :)
Lowry Pierce Glad it helped out!
@@dannyjohnsonsgarage Hi Danng! My name is Luis Urbieta and I have a question. What dos VDC and ABS stand for? Love how you explained what you have to do and we have a Nissan Centra that does that. Please answer my comment when you can. Thanks.
@@luiselapostolfeliz2421 vehicle dynamic control, anti-lock braking system
@@vortecturbo OK thank you.
It could also be the abs relay if the lights keep coming back
U saved me literally i got to work and the abs started running the test and i turned off the car and that noise came on i did what u said and it worked
I’ve had the same thing happened to me several times. Went with intuition once I learned where the noise was coming from and figured out a method that actually works ever time! Whenever I hear that sound and see all the lights come on, I quickly find a spot to pull over and turn my car off. I pump the brakes a few times and then start my car and put it in reverse. I drive back about 10 feet or so and then put it in drive and either drive to wherever I’m going or I will drive forward for a little bit and then stop and turn off my car again. Once you’ve done that and turned it back on, the sound will go away but the lights will stay on for a few minutes. If it doesn’t work, try it again. If it’s still on, you might need to look into it. Hope this helps you guys!
Good advice. Essentially you are having the car run an abs test. This is the concept for driving in a circle or starting the car and driving off. You’ll hear the psssssh sound as it tests.
Girrlll..... Thank you! I did it and it worked!!
I have a 2009 Infiniti FX35 that is making this the buzzing sound a few seconds after I drove off. This fix method did not work, unfortunately.
Thanks Danny that really helped. I have a 2008 Skyline with that problem. So thank you very much. And ironically my name is Daniel and they call me Danny too.👊🏽👍🏾
I have a 2003 Nissan murano. With the same problem. I Just add brake fluid and took care of the problem
Juan Burciaga Nice! 👍🏼
How low was your fluid?
I dont have that humming noise but ill try this later... I have had all these 3 lights the past 2 years lol... Car is running fine but of ocurse no traction control or ABS...
this just happened the other day to me it's the craft shaft position sensor all the lights gone now the shop fixed mines yall welcome 🎉🎉❤
That, as well as many other sensors or fluid levels can cause the lights to come on. Great job finding the issue 👍🏼
@@dannyjohnsonsgarage u right I forgot to add that in 🤜🏿🤛
Bruh... ive wondered what that pffff noise was for years 🤣🤣🤣.. thankyou!!
Every morning at pulloff the car would go pffff and i just got used to it.
hello, i tried what you mentioned, my lights are still on.... HELP
You’re the man! Thank you. I recently replaced camshaft sensor b1 on 2008 fx 35. Since then vdc, slip lights won’t turn off and its been stalling in motion. Added some coolant and battery was unplugged for 10+ minutes. Should be good now. Do you have recommendation on fuel saving? Recently changed both air filters and where am I is extremely cold with traffic jam. Do you recommend fuel injector cleaning additive?
I would only suggest adding some sea foam to the gas tank only (one gallon of gas for each ounce, so you’ll want to put it in when filling the tank). Otherwise, use the cruise control when you are driving steady and that’s the best milage you’ll get. It does make a difference
Thanks Danny, it worked and my OCD can rest again.
Glad you found the video. I have more videos like this you may enjoy th-cam.com/play/PLIjr-uSYDZi6cuomOpHL7rGWNEbQUmbvy.html
Love the way you explain what to do
Brake fluid was low (almost time for new brakes). Thanks!
Thank you. The solution to my issue was an easy fix when I discovered that it was a low coolant level that was causing my ac to blow hot air. 👍
Richard Herrera I’m glad the video helped 😉
Im having to fill up my coolent over and over and i seen on ac line like if coolent was coming out of it idk what to do
It could be the brake pedal switch, any ground wire under the hood or loose battery
Gracias !!! Me ayudo mucho su video y me ahorro mucho dinero 😊.
You’re a lifesaver!! It was the coolant. I’m back on the road 😎🙏🏾
I was actually low on all 3 😂 but how low was yours? I tried everything and I can’t get the lights to go off.
My 06 G35 does this sometimes. I just pull over and park, turn the car off and back on, put it in reverse and go about 15 feet and stop and the humming sound stops but the lights stay on until I turn the car back off and on again, I never have to disconnect the battery. Thanks for the video.
After turning my car on and off G35 2005 6mt, I backed out to drive it to Shell station (having not read your post). I decided one last time to turn it on/off and it worked like you said - I drove it back and parked it. I will find out tonight if it works. Thanks!
ok thank you Danny I was trying not to spend so much on it I was told it might cost me 12 to 15 hundred just to replace it
Thanks for your video . Just now that happens to my car . And I was serah for the meaning .
Thanks you give my the reason.
Bad brake pads can cause this and a broken wire near a wheel
I tried to do this and it came back on so many times...I have had a problem for a year and a half and taken my car to several mechanics.... and had to do a manual reset everytime before I start the car just for me to figure out it was a position sensor...the position sensor fixed my problem and I can start my car like normal again
Before changing it did it crank long?
Thank you so much for all the information you shared with me.
Good s!#! Sir, Quick fix on my Gf's daughters car I appreciate thanks for the tips! 👊🏼⚡️
I saw the flat tire sign ON. Please let us know if you have info on that to put Off. Thanks brother
If the tire is full it’s most likely the sensor that is battery operated. The battery will die and it’s part of the valve stem so you have to remove the tire th-cam.com/video/nUNDvEzUjhI/w-d-xo.html
My daughter cat did this when the temperature got down to 19 degrees.
We will try to unhook the battery and see what it does.
Thanks for the input.
Just got my fixed to day to stop all this get ur crank angle sensor fix.and car back up to power runs fine
Thanks sir.. valuable video👍👍👍
If you cannot take off the light with scanner tool does it refer to faulty sensor?
It just happened to mine this morning, didn't disconnect anything , mine is 2006 auto coupe , I just switched transmission (D) to tiptronic (manual) and they all disappeared at once lol
Very help for my car ABS😁😁😁
Great video. I started with checking fluids. My power steering was a little less than half full. Topped it off and it’s all good now. If it comes back on, I’ll try disconnecting the battery.
I don’t know if it’s related but after VDC and Slip came on, I got a flashing air bag light. I found another video how to fix that and it worked. I have a 2008 Nissan Pathfinder so at this point it’s a 13 year old vehicle. It’s just gonna have issues. Luckily TH-cam helped me fix box of them. Great video!
I’d look into this just as an option th-cam.com/video/wrqENuNtngM/w-d-xo.html
I saw that 10mm craftsman wrench 🔧
Thanks so much! Worked like a charm on my son's 2005 Infinity G35X with 135k miles. All fluid levels were correct - not sure what causes this.
It can also be a dirty wheel speed sensor or a sensor like the cam position, crank position, mass airflow, etc
My sparkplugs and coils were just replaced after that went home when I made turn car turned off engin light came on and all other lights did what your. Video showed lights came off but it still turned off as I'm driving
when you start you car are you pressing the brake?? because i have these lights now and i didnt have them before
Abs relay . You need the codes scanned. What he did is just a system test and reset . It's not a fix. You need a scanner that reads abs codes. Just repaired mine and it was the abs relay
Just bought a used one. Thanks for the heads up on the system testing itself. 👍🏼
Thank you. That's great demo with clear explanation
Thanks! Had 2 out of 3, low brake fluid & power steering. Topped off both and lights went out. I'm sure the Stealership would have told me I need to replace all bearings and ABS sensors for $1,200.
TOMCAT631 They wanted $80 for less than one ounce of brake fluid for the power steering- after I told them eagan was wrong (my father in law took our car in without us knowing when he borrowed it).
TOMCAT631 make sure you see my other videos on this car! th-cam.com/play/PLIjr-uSYDZi6cuomOpHL7rGWNEbQUmbvy.html
Ok
Question..
Traction control "vdc" ..
Please explain ,what's the difference on
Drive on vdc on, and driving on vdc off.
Thank you
Vehicle dynamic control VDC means traction control. It’s automatically on when you drive, which helps the car with stability. Turning it off when you push the button is disabling it and now you’re in manual mode as if the car did not have any kind of traction control. Some vdc systems can apply the brakes on only one wheel to straighten the car out.
@@dannyjohnsonsgarage
Thank you very much.. "👍
i have infiniti g35 and have this problem and your video helped but now my battery and brake light is on I changed the alternator and battery and its still on.
The brake light should just be some slack in the cable and the battery light (and the brake light) may just be coming on like mine do. Try gently pushing up on the gauge cluster visor hood and see if the lights turn off. Mine turn off when I lift on the gauge cluster visor
You get it fixed?
I got an M45 with the slip and engine light on. I’m going to top all the fluids and disconnect the negative battery terminal to see if that clears them because right now it’s in fail safe mode.
You can also have the codes run at just about any auto parts store for free and they might be able to tell you a sensor you need to buy that is bad
@@dannyjohnsonsgarage I’ve seen the speed sensor on auto zones site for like $25. That may be the culprit, if so I’ll do that but I do need the diag check, I tried checking the diag through the menu and it couldn’t complete it because their was a malfunction
I have a 2007 Infiniti fx35 and my mph just stopped working then the abs and slip light came on then I turned my car off and it went off but my mph still doesn’t work any suggestions?
I came here to learn how to make my car less safe, i learnt how to keep it safe
So I have a 2005 6MT g35 and those three lights come on randomly as I drive the car and once I turn off the car, I hear the buzzing you talk about and I have to try and get the car to re-test the abs system by restarting it and driving a little then maybe the buzzing will go away. My fluids are all topped off but I do have 2 different codes coming up. I have one for an O2 sensor and another for the pnp switch. I changed the pnp switch but the code still comes up
I would start with the codes and get the 02 replaced, but if you are hearing the buzzing, it sounds like it’s the abs module/pump. You can try gently tapping on it, but if it just won’t go away it may need to be replaced
THANK YOU MY G! MAKE SUM VIDEOS LIKE THIS SO FCKING HELPFUL THE EXPLANATION CLEAR AF
I have the same issue with my 2005 pathfinder. Took it to Nissan and they told me there was a circuit break on the left rear speed sensor. I replaced the sensor twice and still giving same error. My ABS/VD/SLIP and now my 4WD and Brake light is on. WTF.. Dealer want to replace my wiring setup for $1500... And it's not even a guarantee to fix the problem. I'll try checking the fluids and disconnecting battery when I get home. I need the 4x here in Wisconsin.
just got scammed out of a g35 and this slip light comes on and will limit power ( ABS , VDC OFF) are both staying on and the slip warning will flash when i drive sometimes
I have an m35x and while I'm driving it would shut off and those lights will come on after a few minutes it will start back up can I have the same problem
Facts same for me, did you fix it by any chance if yeah what was the issue, this recently happened to me when I tried to switch a fuse.
Thank you thank you!💜💜💜💜💜💜💜💜💜💜💜💜
I have a Nissan Altima and it showed these three specific lights on the board. I was driving and I almost freaked out and it also did that humming noise. Then I turned the car on again and they were gone.
Thanks so much man this helped when I was out driving my family
Thanks so much bro good Chanel
About to try this now.power steering fluid is right under minimum line.oil was crazy low (sons car), hopefully that fixes it.it also randomly stalls and drains battery.🤦
Hey, I have a 2010 infinity qx56 , I change 3 tires after that around 3 hours I got the SLIP VDF off lights on
Are they all the same size or different size wheels?
After the buzzing is off you can turn off your car and turn it back on again you don’t have to disconnect the battery.
It depends. I’ve turned the car off and it continued to buzz with the car off
THANK YOU. GOING TO CHECK MY 2012 SRX - WHICH ABS AND STABILITRAK ARE BEING ON FOR A WHILE. AND A NOISE IS COMING FROM ON THE FRONT OF THE CAR LIKE SOMETHING IS RUBBING AGAINST SOMETHING. I JUST REPLACE THE ROTORS AND BREAK PADS ON THE FRONT, INCLUDING THE DRIVER SIDE WHEEL BEARING. I STILL HEAR THE NOISE AND SOMETIMES WHEN I BREAK IS LIKE A THE BREAKS ARE SKIPPING. I THINK I GOT AIR ON THE BREAK LINE.
Here is how to bleed the air out of the brakes. th-cam.com/video/h5HV9D2sezs/w-d-xo.html
Danny your a real one
Question random shutdown and trouble starting here and there. Same lights. 06 m35x infinity
Changed crack shaft sensor no go. Cam shaft sensors next? Sez there is a left and a right one.
Great video and explanation
Question,
When the slip and vdc lights go off on my daughters infinity m35x goes off there’s like a hesitation and scraping sound coming from the drivers side of the car.
Things that have been replaced
Axel(2)
Drive shaft
Carrier assembly
Note: the vdc & slip light came on after this work.
ANY insight would be very helpful
Could possibly be the wheel bearing (make sure the axle nut is correctly torqued).
Danny Johnson thank you we’ll try that
My 2007 m35 does this but sometimes while I’m driving the car turns off , I believe it can be my harness is damaged because I had to replace the fuse connecters to the battery terminal
Thank you very much
thanks for sharing sir,i have a 2015 quest and after that freezing temperature here in chicago that light and brake light would come on on cold days,in the summer it would not..i have to try what you did..thanks so much
I’m glad it worked. Sometimes it just needs a reset when nothing is really wrong. Take care!
Hey Danny I hope to hear from you soon for I am stuck In a hard spot. This wouldn't be so hard if I had access to a code scanner but i do not.. none of my neighbors have one and I am almost an hour away from the nearest shop with the broken vehicle being my only one at the moment. My wife had the 03 Infiniti G35 at work and she called me saying there was a VDC, Slip & At Check and check engine light and the oil light was on. All the resivors were about half full and the oil maybe needed half a quart if that. The blinkers, taillights and the head lights (50%) of the time do not work. The car does not run very good cant make it to work until it's fixed. My neighbor is running me to advance 1 time get parts. If it's not fixed or I guess wrong im fuced. My final guess before I go is cam shaft sensor. Let me know what you think
What was your issue??? My cam and crankshaft sensors need replacing
Just had this, and this tips really work. Thanks man!!!
Ok Danny just watched video today and you gave great info....but what you think the problem is if it's not starting back up. The security red light is not on and the key will not turn
Gavin Hampton You were saying the key is blocked and will not turn? Try slightly turning the steering wheel and then trying to turn the key
For me I have an 07 6mt coupe g35 and the car just jerked and my check engine ,slip and vdc light came on i shut the car off i turned it back on all lights were still on later that day i disconnected the battery from the car and waited 10 min i connected it back and the check all lights went away but as i drove off the car jerked again and my vdc and slip light came on and to this day after i drive a few feet to the left the lights will come on
Thanks Danny
You’re welcome! Feel free to see my other videos on this car! th-cam.com/play/PLIjr-uSYDZi6cuomOpHL7rGWNEbQUmbvy.html
All 3 of these lights are on in my 05 fx35, my gas pedal has no pressure, is that suppose to happen when the abs, slip n vdc light turn on?
The lights all come on for any sensor or fluid level, so it could be from a throttle position sensor, crank position sensor, low fluid levels...you’ll have to find out which one is causing it. If you can get a code reader it may be able to tell you
A+
My VDC, ABS, Slip and Brake lights in my Pathfinder come on when I reach 16mph, at the same time the doors auto lock. This started one day after I "slipped" at a red light on the wet street. I will make sure my fluid levels are ok but I am thinking its just a malfunction.
Years ago in my Maxima my factory premium radio and CD player stopped working. I refused to replace it. It was rough. LOL!! About a month in when I actually was about to break down and buy something new, it just began working again flawlessly.
My issue just randomly went away just as I expected. Glad, once again, I didn't panic and go to the dealership.
Misalignment or incorrect tire size from wear or wrong XXX/65/20 for example
i had a VDC and ABS light come on... when i mis aligned my wheels... (rear).
I realigned my wheels and the ABS system no longer noticed wheel ratios turning at different speeds...
its most likely, incorrect tires/worn tires/ incorrect wheel alignment .. .or last a level suspension indicator(little plastic arm) is broken or popped off the frame.
Hi Danny. I have the same problem with my 2005 G35x. Big problem is the ABS pump keeps going even with the engine shut off, and after about 1 hour the battery has run down so car won't start Any idea what causes this problem in the first place? I have to disconnect the battery when I park the car or it won't start when I want to drive it. This is a real pain in the ass. I have a few ideas that I will try tomorrow.
Did you ever figure this out? I have the same issue I’ve been trying to fix.
My 05g35 is doing the exact same thing. I heard the abs module running the other day and disconnected the battery to stop it and i guess reset it. I didn't hear it in the thunderstorm last night and car was dead as hell this morning UGGHHHH... did you figure out why the abs module would constantly run all night with the key off? ?????
I hit a pot hole hard once and all the lights came on and then it came off after making like 3 runs with my car to places and I guess I went over “rumble” speed bump regular speed and these lights came on again and it’s annoying to me. I haven’t made any runs anywhere so I wanted to see if I can get these lights off by pressing somthing on my 08 Infiniti G35x…I guess I’ll just wait till they go off on it’s own like last time.
Many thanks. It worked on my infiniti fx35. All lights are off.
I have a 05 Nissan psthfinder both lights are on so we unhooked the battery cable for like 20 minutes they arevdtill on so im going to find a place where I can drive 20 mph. Fir about 15 minutes and the stop and turn it off and then start it up again. I can t afford to put any more money in it
Please help...is this what I need to do I am a woman ive put new breaks all around new tires all around new rotors all around and the front end lined up. Right St 1700.00 bucks not counting what I paid fir it
So I pray this works thanks all!!!