Honestly...you ALMOST have me convinced I can do this to my ET2! 😉 (Well, not while the temp is 45 C/114 F outside...) Great work...I've come to depend on your expertise above other scooter channels. Thank you for being here...
Finally got mine running right, a big problem was the auto choke not performing correctly. I installed a manual choke and then i could see it was running lean on full throttle. Thankyou guys for your ongoing help, appreciate it. Final setup : 70cc replica kit with stage 6 exhaust 4.5 gram rollers 98 main jet stock pilot jet (32) purple torque spring stock clutch springs
I think the little zip will still run surprisingly well with the street pipe. But will be a while lot better with the Yasuni R. Looking forward to pads two.
Great Video Brad. Looks like I might have found another improvement for the TBG after I get the accelerator I ordered from you fitted... 70cc kit next!!.
Hey man I was wondering what fuel oil mixture premix for a euro 2 piaggio typhoon 50cc I have the following installed : Mhr replica kit 20.5 mil delorto carby Yasuni r Super compression crank And help on this would help me out heaps
Hello! How stock crank can handle that? Planning same with stock crank. Also jetting info with stock PHVA 17,5 would be nice. I am using Leovince TT exhaust.
Hello. This is a bit off topic but in my 2t air cooled peugeot speedfight 3 in the stock exhaust theres another "pipe" poking out off it. Im sure it is a secondary air injection mechanism or something. Does it do any good to block the system off and remove it completely?
@@scooterstreetau Yes its a "Pollutant emission control system" according to the manual. But I just took it off and did a small test drive on it and it doesn't feel like its doing any bad. Im not really sure if I should leave it like that or put it back.
Thank you brother🙌 You can use the oil if it is specified to your engine. The Aprilia you mention may be 15w50 so stay with the specified recommendation in climate.
What do you think my scooter has blue smoke with a 70 mainjet, but boggs on full throttle? My setup is a athena 70 sport, leovince tt and a dellorto 21mm carb, with a malossi digitronic cdi. my scoot is a piaggio typhoon 2020
@@scooterstreetau i havnt really focused on the needle since it doesent affect full throttle, but whenever i go up in jet, it lets me full throttle, but it sounds much deeper and slows down
Hey, i just got a zip yesterday, previous owner said its a stock 70cc zip directly from italy, it says 49cc on the papers, how would i check wether it actually has 70cc or not?
@@scooterstreetau yeah I know what they are for but you got different ones from the factory, I rebuilt a lot of piaggio engines for friends and for myself, i’m pretty sure I got a box of them somewhere 😂
@@scooterstreetau Oh they are really that rare in Australia? I just bought one some months ago and I am really in doubt where I should start tunning this machine since I plan on doing it over time. Engine or transmission? What are your future plans of this scooter? And could we get a little peak on it sometime?
@@Angerfisters Perhaps start by ensuring all systems running as best as possible, then it will depend on your budget and your plans. Exhuast and trans. We plan to make it a Street Scooter😜😜
Is part 2 of this video coming soon? Iv ordered the 70cc street kit from you and iv only got the stock exhaust ATM. I do won't the wild lione exhaust next.
I put a stage 6 pro replica chrome exhuast on my zip with dr70 witjh orignal carb. top speed is the same but accelration in terrible. What changes should be made to gain performance. Or is the exhuast jus too big for the cylinder.
@@scooterstreetau yessir ive seen the videos you guys are probably one of if not the best scooter channel on yt. Its just looking online generally everyone suggests changing the crank on the bike because the factory one maybe good but it isnt strong enough to withstand more rpms than 10-11k (I have a sr50 with the piaggio hiper2 lc) so thats why ive ordered a new doppler endurance crank to try and build up the bike slowly and now i think i probably should have got a kit first then replaced the crank but i guess you live and you learn lol
@@davidn6546 Thank you David🙌If you have the budget you should change the crankshaft to match the cylinder. Replacing the crank first as you have done is an excellent way to upgrade the engine, get it done and build on top, well done mate👍
yes so true. 99% without exagerration have leaked from what we have seen. It became part of the service to repair the oil leak, same for Aprilia, Vespa n Piag.
@@frankdaman9823 That is true but the Air cooled zip has no radiator and no cooling pump or cooling system, so why would you put the SP Cylinder on when it has no water cooling system?
@@scooterstreetau can put a electric pump on, reduces motor friction to by not using the usual engine powered pump, and i think malossi makes a better mount for the sp it wouldnt be hard to put it on a ac zip, can let you know within next six months slowly started buying parts untill i can go for a rt95 kit
Thanks for the best scooter channel on TH-cam, interesting to follow your projects. / Per Lidberg Sweden
Thank you, love the support from you guys🙌
Honestly...you ALMOST have me convinced I can do this to my ET2! 😉 (Well, not while the temp is 45 C/114 F outside...) Great work...I've come to depend on your expertise above other scooter channels. Thank you for being here...
If you have a video request we may be able to arrange.
Finally got mine running right, a big problem was the auto choke not performing correctly. I installed a manual choke and then i could see it was running lean on full throttle. Thankyou guys for your ongoing help, appreciate it.
Final setup :
70cc replica kit with stage 6 exhaust
4.5 gram rollers
98 main jet
stock pilot jet (32)
purple torque spring
stock clutch springs
Great result, good work.🙌
I think the little zip will still run surprisingly well with the street pipe. But will be a while lot better with the Yasuni R.
Looking forward to pads two.
yes for sure, we have a new Yasuni R sitting in the box on the seat, we plan to show the fitting tuning video very soon.
Great Video Brad. Looks like I might have found another improvement for the TBG after I get the accelerator I ordered from you fitted... 70cc kit next!!.
Good stuff, check that crank first..
Would you be able to make a vid on taking off and breaking down the Aprilia SR50R engine
We are actively looking for an SR50R at the moment for a SR50R Series.
@@scooterstreetau That would be so helpful as i’m putting a new cylinder kit and crankshaft into it
Hey man I was wondering what fuel oil mixture premix for a euro 2 piaggio typhoon 50cc
I have the following installed :
Mhr replica kit
20.5 mil delorto carby
Yasuni r
Super compression crank
And help on this would help me out heaps
Start at 30:1 and lean off as required.
@@scooterstreetau how many tanks do I run 30:1 and then what do I lean it off too ?
Thanks heaps for getting back to me 👍
@@frazenin9637 Check the plug on a regular basis, monitor how the engine is performing.
Have you disenegaged the oil pump?
@@scooterstreetau yes I have and removed the oil tank
is it ok to remove all of the secondary filter/box system , putting a blanking plug at the crank case?
Yes we have done this before .
Hello! How stock crank can handle that? Planning same with stock crank. Also jetting info with stock PHVA 17,5 would be nice. I am using Leovince TT exhaust.
Yes and yes but upgrade the crank soon.
Hello. This is a bit off topic but in my 2t air cooled peugeot speedfight 3 in the stock exhaust theres another "pipe" poking out off it. Im sure it is a secondary air injection mechanism or something. Does it do any good to block the system off and remove it completely?
Hello, I would have to see this pipe your describing. I would assume it is part of the emission system.
@@scooterstreetau Yes its a "Pollutant emission control system" according to the manual. But I just took it off and did a small test drive on it and it doesn't feel like its doing any bad. Im not really sure if I should leave it like that or put it back.
Hey mate I love your videos, just a question, can I use motorcycle oil in my 125cc Aprilia scooter for the engine oil?
Thank you brother🙌 You can use the oil if it is specified to your engine. The Aprilia you mention may be 15w50 so stay with the specified recommendation in climate.
What do you think my scooter has blue smoke with a 70 mainjet, but boggs on full throttle? My setup is a athena 70 sport, leovince tt and a dellorto 21mm carb, with a malossi digitronic cdi. my scoot is a piaggio typhoon 2020
small amount of smoke is ok. Bogging? have you tuned the main jet? Test for rich setting and then change the needle set up.
@@scooterstreetau i havnt really focused on the needle since it doesent affect full throttle, but whenever i go up in jet, it lets me full throttle, but it sounds much deeper and slows down
Can you do a video about the gear up kits for the piaggio zip please ..I'm watching from Dominica , love the video's.
Hello 👋, how is the weather is Dominica? Ok we try, did you see the gear up kit video we did, check in the catalogue under Gears Explained.
The weather's alright .thanks I'll look for the video
Hey, i just got a zip yesterday, previous owner said its a stock 70cc zip directly from italy, it says 49cc on the papers, how would i check wether it actually has 70cc or not?
You can remove part of the engine or Ride it, how fast?
@@scooterstreetaureally quick, not fast, already blew the bearings on crank, full polini build on the way 💪
@@CokieZip Haha ok, sounds like a plan👌
Great video but do you realize the long nuts you used on the head are actually exhaust nuts?
Thanks for the props🙌.Not really, the are to hold the cover from touching the head vanes. They are the same as the exhaust nuts on some scooters.
@@scooterstreetau yeah I know what they are for but you got different ones from the factory, I rebuilt a lot of piaggio engines for friends and for myself, i’m pretty sure I got a box of them somewhere 😂
Hello mate! Great videos and super informal.
Have you ever had a Yamaha Jog R AC in your hands yet and what was your experience with it?
I do own a Yamaha Jog R but it is only one in Australia, we have not done any work on it as yet.
@@scooterstreetau Oh they are really that rare in Australia?
I just bought one some months ago and I am really in doubt where I should start tunning this machine since I plan on doing it over time. Engine or transmission?
What are your future plans of this scooter? And could we get a little peak on it sometime?
@@Angerfisters Perhaps start by ensuring all systems running as best as possible, then it will depend on your budget and your plans. Exhuast and trans.
We plan to make it a Street Scooter😜😜
cheers mate!
Ill look forward to your project on it (:
Is part 2 of this video coming soon? Iv ordered the 70cc street kit from you and iv only got the stock exhaust ATM. I do won't the wild lione exhaust next.
Ohh yes it is, sorry we have been side tracked with other projects.. Stay tuned.
I put a stage 6 pro replica chrome exhuast on my zip with dr70 witjh orignal carb. top speed is the same but accelration in terrible. What changes should be made to gain performance. Or is the exhuast jus too big for the cylinder.
Upjet the carb. Also adjust the needle aswell. Start with a 120jet then work down.
@@JDMz more fuel with neddle or less
lighter rollers 4-4,5g, malossi red sponge, yellow cluctch springs, main jet…
jet
Have you made changes to the transmission? What have you done to the variator and the clutch.?
can you make video installing 70cc on gilera runner new gen
We have a watercooled engne cylinder fitting coming soon.
Did you change the crank?
No, not for this build. We will get to doing on this Zip at one stage. New crank bearing seal kit.
@@scooterstreetau so you can run a mhr rep on a stock crank?
@@davidn6546 If you follow the guide you can. Have you seen any of our other videos?
@@scooterstreetau yessir ive seen the videos you guys are probably one of if not the best scooter channel on yt. Its just looking online generally everyone suggests changing the crank on the bike because the factory one maybe good but it isnt strong enough to withstand more rpms than 10-11k (I have a sr50 with the piaggio hiper2 lc) so thats why ive ordered a new doppler endurance crank to try and build up the bike slowly and now i think i probably should have got a kit first then replaced the crank but i guess you live and you learn lol
@@davidn6546 Thank you David🙌If you have the budget you should change the crankshaft to match the cylinder.
Replacing the crank first as you have done is an excellent way to upgrade the engine, get it done and build on top, well done mate👍
Never really saw a zip leak at the fuel level censor but holy f*ck did I see a lot of oil sensor leaks😂😂
yes so true. 99% without exagerration have leaked from what we have seen. It became part of the service to repair the oil leak, same for Aprilia, Vespa n Piag.
Cant you just put a zip sp cylinder on there?
I think the water cooled cylinder will fit. Seems a waste due to the SP having water cooling built in to the cylinder.
@@scooterstreetau that doesnt make sence to me, a zip is ac a zip sp is lc, my opinion lc is more relible keeps heat down better and can do long trips
@@frankdaman9823 That is true but the Air cooled zip has no radiator and no cooling pump or cooling system, so why would you put the SP Cylinder on when it has no water cooling system?
@@scooterstreetau can put a electric pump on, reduces motor friction to by not using the usual engine powered pump, and i think malossi makes a better mount for the sp it wouldnt be hard to put it on a ac zip, can let you know within next six months slowly started buying parts untill i can go for a rt95 kit
@@frankdaman9823 We have converted an Air cooled Zip to water cooled system using SP LC parts before, yes it works. Very expensive.
mhr replica is steetrace. its 70* of the mhr pay that bit more for 30% more power
nice
👍👍
ugh i wish the Netherlands werent as strict when it came to scooter/moped speed laws :/
Doe gewoon een skipper blokje eronder, en dan bewerk je gewoon je hitteschildje dan lijkt het op 4t samen met de 4t luchtfilter
Bitchmove gewoon minder huilen meer gassen lul
@@JustRicardoNL skipperblok nergens te koop of heel duur
god bess you. Thanks so much .
06 Bws
🙌Thank you brother.
No squish gap check ?? 🤯😱☹️ No ring gap check?? 😭😖 professional?
Thanks for commenting, I guess you didn't watch the videos where we demonstrate squish and checks?