It's not a proper helical tooth when cut this way. There is only one point of contact at the very center of the tooth, and this creates a lot of friction because of the high pressure at that point. It will wear rapidly if it is transmitting very much power. You should cut less depth and then finish the gear with a hob. But if that is not an option, then cut shallow, and move the workpiece over one tooth pitch, and plunge again. This will shave the top of one side of the tooth. Do again on other side of the tooth. Then increase the table angle a few degrees more, and shave the corners of the tooth so it will clear the worm, while not excessively cutting away the center of the tooth. You necessarily have to overcut the depth by a lot to get the worm to seat deeply enough.
The finished worm gear is beautiful. Thank you for showing us this. Watching you with your beard so close to spinning machinery made me nervous. I'd have it tied up and pulled close under my neck while I was working. And yes, I used to have a long beard.
Caracas, fui fresador por muitos anos, fiz muitas coroas igual a essa, mas pra mim é novidade fazer dessa maneira, sempre fiz, com bits, e caracol. Parabéns, ótimo trabalho
В 67 году я работал на заводе фрезеровщиком. А мой брат зуборезчиком. Там закладывалась обойма заготовок под шестеренки, от пяти до восьми штук. Включил станок и сиди смотри. Работа не бей лежачего. Как у Револьверщика! А фрезеровать по одной заготовке сегодня. Это полный отстой!
Se um cidadão pessar mesmo não vai soltar de aramcos a embreagem saber usar mesmo tai senão vai ter que tirar escorpião do bolssso mesmo engrenagem são caras pra fazer mais aimda top
Это мягкий металл . Шестерня в редуктор , должна такая быть , поливается маслом , в случае отказа подачи масла съедает только её а остальное остаётся целым
Очень распространённое заблуждение и восторженные отзывы безграмотных "мастеров"... Это червячное колесо лишь похоже внешне на то, что должно быть. Невозможно нарезать методом копирования дисковой модульной фрезой то же, что должно быть нарезано методом обката червячной модульной фрезой, причём полностью повторяющей геометрическими параметрами рабочий червяк передачи. Внешне будет похоже, но не будет правильного пятна контакта в зацеплении и очень быстро сначала появится люфт, а затем и износ. Но для продажи непонимающим пойдёт на ура, ибо товарный вид на должном уровне!
I guess if you want to be real machinist you have to live in India now… this does not happen in the states. Everyone is lazy. Cnc machines have definitely depleted our skilled workforce.
It's not a proper helical tooth when cut this way. There is only one point of contact at the very center of the tooth, and this creates a lot of friction because of the high pressure at that point. It will wear rapidly if it is transmitting very much power.
You should cut less depth and then finish the gear with a hob. But if that is not an option, then cut shallow, and move the workpiece over one tooth pitch, and plunge again. This will shave the top of one side of the tooth. Do again on other side of the tooth. Then increase the table angle a few degrees more, and shave the corners of the tooth so it will clear the worm, while not excessively cutting away the center of the tooth.
You necessarily have to overcut the depth by a lot to get the worm to seat deeply enough.
Да тут мало кто понял, что это не шестерня, а червячное колесо
I was a fitter machinist for 12 years and I always wanted to learn how to use a dividing head but never got that chance. Nice work!!
It's not so hard a a machinest an then die maker I got a lot of hard jobs at a young age the dividing head is not.
That hard we make it sound hard all the answers you need are in your machinist hand book all the tables now you know
😂😂😂Тоесть с выработкой старая деталь и сделал он так же новую
The finished worm gear is beautiful. Thank you for showing us this.
Watching you with your beard so close to spinning machinery made me nervous. I'd have it tied up and pulled close under my neck while I was working. And yes, I used to have a long beard.
Сделал такуюже изнощеную шестерню , только с нового метала😂
Если вы считаете радиусную впадину по окружности износом, то ошибаетесь.
Странно, что с такой бородой работает на таких станках. Это не смелость, это безрассудство.
И не только из нового металла, а из какой-то латуни
Они там моются в Индии в реке где трупы плавают, какая ещё техника безопасности)
They mistake is to use the mill as a lathe in a moment...do the turning of the Center with a lathe before the milling!
Perfect, such a beautiful gear.
Beautiful work manual machines I love it
Caracas, fui fresador por muitos anos, fiz muitas coroas igual a essa, mas pra mim é novidade fazer dessa maneira, sempre fiz, com bits, e caracol.
Parabéns, ótimo trabalho
В 67 году я работал на заводе фрезеровщиком. А мой брат зуборезчиком. Там закладывалась обойма заготовок под шестеренки, от пяти до восьми штук. Включил станок и сиди смотри. Работа не бей лежачего. Как у Револьверщика! А фрезеровать по одной заготовке сегодня. Это полный отстой!
Making worm gears was one my favorite gears to make.I just can"t remember how I use to do it.
Tolle Arbeit! Bin begeistert wie man sowas herstellt! 👍💪💪
Вот , что мне нравится , так это их оптимизм и краствые ПЕСНИ !!!
Угол винтовой линии считается по формуле , а для этого нужен червяк, деаметр фрезы также выберается по диаметру червяка .
Mantap bang Gani...thegyuse Chanel sll nyimak..😅
Крепление заготовки конечно.... Имея такой токарный станок, можно было втулку выточить, чтобы закрепить как надо заготовку
Coś piięknego takie umiejętności. Pozdrawiam.
Thanks 🥰
Un buen trabajo todo un profesional fantástico 👌
Отличная работа 😃👍
Excelent work man!
Thx🥰
Excelente fresador. 🎉🎉🎉
Nice work man 😊👍
Thx 🥰
Як довго прослужить та шестерня ? Зробили з дерева чи на принтері 3 d
All by hand 🤚 no Cnc stuff there
Yes
No CNC, how do you think this stuff was cut 30+ years ago? It's not rocket science
A lot more people would die if CNC wasn't developed
Wow
Really?? by hand ??
И снова волшебные тапочки в действие! Я знал что все дело в тапочках!
❤
分度頭會有偏差!
That's what you call a real machinist...all by hand...no programing no computers
I was taught to use a manual lathe in metal shop...still remember a few things
A real machinist just does it by program because it's faster and much more precise.
Machinists machine shit, use the right tool, and make sure it is done roght
@@panda3d180what are u telling? What he's doing isn't entirely precise.
Merci,pour la démonstration pratique mais si c'est possible je cherche une explication théorique
www.youtube.com/@VintageMachinery
Борода на шпиндель намотаться может!
Им пох.
What's the application of this gear?vehicle?
I don't think this how you make worm gears. You should get a proper hob comb, and it is not that expensive compare to other cutter.
Minute 2 10 and forward
Hát ! Vannak kifogásom, de majd bele jössz .
Tive frisadora igual a essa. Pedras-ímãs da Dinamarca
Servisso top mas não admite erros e tudo milimetramemte emsima do mosquito se erarperde todo o servisso e babal very good
Great !
Fine job
Se um cidadão pessar mesmo não vai soltar de aramcos a embreagem saber usar mesmo tai senão vai ter que tirar escorpião do bolssso mesmo engrenagem são caras pra fazer mais aimda top
👌 👍
Только с
делай в точ точ такую же😂
Good job
И где приминяется эта шестерëнка из бронзы? 🤔
Gear box
Шестерёнки из цветмета применяются там где на них нет большой нагрузки.
Zabardast
Awesome 👏
Super nice 😊😊😊
BEAUTIFUL❤❤❤
MACHINE"WIRE CUT"
由莉真中古藤四郎藤咲
Milling cutting
Индусы я так понимаю.. Вечно они выдумывают как сделать на коленке
Im from Pakistan
Индусы теперь на коленках не работают. По технике уже нас превзошли.
Is this brass?
Yes
@@GhaniEngineeringworkраспространённая ошибка применять латунь вместо бронзы. Но это не антифрикционный материал!
Vn cách đây 20 năm dùng mai fai lăn sx tốt hơn này…..
Очень похожа эта бронзовая шестерня на шестерню редуктора японских крановых установок
Это латунь. А если ты видел только шестерню в редукторе японских крановых установок то тогда это точно она😂
Если эта шестерня на редуктор. То у неё большая динамическая нагрузка на зуб. А значит она не из цветмета. Кран это напряжение всех шестеренок.
Cnc mãi đỉnh
This guy looks like he cuts twice and measures once
What kind of metal is that?
Gun metal
Isnt brass too soft?
@@danial_amini gun metal hard
@@danial_aminiit is, that's why it's cutting so fast. Won't last long this part.
ماشاءالله
At least this time they didn’t use methods that would be less than desirable great job
That's not a worm gear... that's what gets driven by a worm gear!
Coroa.....
This is the gear the mate that drives this is the worm.
Very crude
Хм, привсем уважении, но прослабили, Что-то мне кажится не долго ей работать.
Pakistan?
Yes Pakistan
Do not wear full sleeved shirt when operating machinery.
Есть здесь рулевые червяки?
Yes
Good
А почему без воды?
No
Потому что бронза латунь на сухую обрабатывается
Looks a mess, I'd be asking for a refund or a new one better made.
That's a pinion gear, not a worm gear.
Coroa pinhão é o eixo acoplado nela
Worm gear
Только наши неготив пишут
Когда нибудь ему бороду намотает
🤙🤙🤙🤙🤙
So Primitive.
Third world technology
Ok
Para mi su pieza esta mal echa la hizo igual que la pieza vieja gastada
Pederson da Dinamarca
Pakistan
Бешельмеки всё так же продолжают клепать всё на коленке 🤦
Язык самый опасный враг
Сам что небудь умеешь толком
Зато обеспечены работой
The whole geometry is wrong, why are the teeth so pointy??
Milling cutting
If it gets heat treatment, will last longer.
Latão....assimila têmpera???....acho ki não
Без закалки это сыромятина, час поработает и разлетится.
Это мягкий металл . Шестерня в редуктор , должна такая быть , поливается маслом , в случае отказа подачи масла съедает только её а остальное остаётся целым
Если всё норм , работает десятилетиями
A machinist here. I have made several similar gears using the same methods, over 14 years now and no problem, gearboxes still in operation.
Лучше молчи, за умного сойдёшь.
Очень распространённое заблуждение и восторженные отзывы безграмотных "мастеров"... Это червячное колесо лишь похоже внешне на то, что должно быть. Невозможно нарезать методом копирования дисковой модульной фрезой то же, что должно быть нарезано методом обката червячной модульной фрезой, причём полностью повторяющей геометрическими параметрами рабочий червяк передачи. Внешне будет похоже, но не будет правильного пятна контакта в зацеплении и очень быстро сначала появится люфт, а затем и износ. Но для продажи непонимающим пойдёт на ура, ибо товарный вид на должном уровне!
Sir mob no
+923107431798
I guess if you want to be real machinist you have to live in India now… this does not happen in the states. Everyone is lazy. Cnc machines have definitely depleted our skilled workforce.
Proud to be a pakistani🇵🇰🇵🇰🇵🇰🇵🇰🇵🇰
@@GhaniEngineeringworkкак можно гордиться тем на что ты повлиять не мог? Это не достижение...
Начало положено..как ляжет на червяк дело второе
Как они работают, спец одежды нет, борода до колен, техника безопасности ноль,
А ты на ихний бороды не смотри тут работу показывают
@@FANTA769 им нужно станки хорошие, ребята башковитые, что такое станки очень знакомо, сам машиностроитель, жаль их что в таких условиях работают,
@@user-yw1bn7ml9d они этим довольны,
Çok kötü olmuş.
Why ?
@@GhaniEngineeringwork her yerinde çapak var onları niye temizlemedin??
it won't conjugate at all, rubbish !
что за наркомания?
?
@@GhaniEngineeringwork шиза
Eww
?
Is this accurate? , garbage
Прослабил, однозначно. Опыта маловато.