BARBER TUTORIAL - SIMPLE STEP BY STEP HIGH TAPER
ฝัง
- เผยแพร่เมื่อ 24 ก.ย. 2023
- 🔥 Enroll in Dreclipperhands Academy Here ➡️ academy.dreclipperhandsacadem...
⭐️Check out our Merch : clipperhands.com/
This video is NOT sponsored. Some product links are affiliate links which means if you buy something we'll receive a small commission.
=============================
The Barber Plug - Promo code "Dreclipperhands" for 10% off - thebarberplug.com
StyleCraft - Promo code "Dreclipperhands" for 10% off - stylecraftus.com/flex-trimmer...
Gamma - Promo code "Dreclipperhands" for 10% off - gammaplusna.com/?gclid=CjwKCA...
===========================
Connect with Me!
=============================
Instagram: dreclipperh...
________________________________
Tiktok: / dreclipperhands
________________________________
Twitter: / dreclipperhands
=========================== - แนวปฏิบัติและการใช้ชีวิต
![อาจารย์ยอด : สวยกินคน [ผี]](http://i.ytimg.com/vi/_-TIJOwkRA4/mqdefault.jpg)
Future barber right here 🙏🏻
That cut was 🔥 and I like the way you explain your work! Very thorough!!💯💯
blessed to have dre teaching me 🙏🏽🙏🏽🙏🏽 appreciate it gang
Beast mode. Super clean my boy
Damn. That cut is so clean
Well by Gods grace I would be the upcoming best barber soon
Dope barber! 🔥 Content. Keep it up brotha!
Great teacher
Satisfying cut
I like the finishing.
Dope cut Dre! I like your attention to details! What straight razor are you using?
Great master
Fire 🔥 cut
🔥🔥 trying this out on me
The comb you used for clipper over comb isn’t on the website in bio??
Is that a mid taper on the back and the sides too cause I'm trying to study different types of cuts and how they will most likely look so I'm just curious
Do you mix tomb45 no drip with alcohol. Or just no drip on its own?
Tanks
🔥🔥🔥🔥
What blade is that on the snap fx .
Hey man would a high taper suit a round face? I usually get a low or mid taper. Was wondering if a high taper would suit my round face. Dope video though dude!
Depending if your vertical bars and short or longer then yes it would. Short verticals I would say don’t but I’d there medium or longer the. Go for it
Yo Dre been cutting for a good 2 month and when I use the #2 guard I can’t get the line off with the 1 1/5, I go open to closed still can’t get it out, any tips?
Try closing your 2 and lightening the 2 open before the 1.5?
If that don’t work use your one open and use the corners
After trying to remove the #2 guideline with the 1.5, try with the #1 guard all the way open. If that doesn't work with the 1 fully open, try close one notch at a time until you fully blend the guide line. Also, start off using clippers with click lever so you always know where you're adjusted at all times. Plus slap a taper blade on those clippers. Fade & faper blades leave harsh guidelines with the longer part of the blend. I always use at least 2 clippers on every hair cut. A clipper with a taper blade to cut anything above the initial guideline & a clipper with a fade blade to help remove the intial guidline & also to detail below the .5 guideline. Taper blades cut & transition so much smoother than a fade or faper blade. Unfortunately most new clippers don't come with a taper blade so you'll have to purchase one separately. Also, all new barbers should result to click levers only.
Also, when you do finally get the #1 guard properly adjusted to remove the #2 guideline, make sure you flick out at the line to avoid creating another line even higher. Also, for guards, I tend to stay away from stylecraft/gamma guards as they stretch the blend too much. Start off with wahl premium guards, which fit stylecraft/gamma clippers too. Just don't use them on clippers with a fade blade. Fade blades that are properly zero gapped will cut into the plastic guards and create a gap between the guard & the clipper blades & cause the plastic guard to fall off. I only use my plastic guards with taper blades cuz they're thicker & not as sharp. Plus it's better for beginners to blend with a taper blade anyway.
Porque en inglés suena re cheto amigooo jajaja
🙂
First
W