A smaller diameter metal pipe also works great to protect the wires. Just push the wires through the metal pipe as you insert the pipe into the trolling motor shaft. It keeps them safe as you cut the shaft. Also best to have the motor upside down to keep debris from falling down into the motor.
*Great little trolling motor **enjoyable.fishing** recommend had it hooked up to my 15 foot old town canoe and it pushed it pretty good with me and my son (220 pounds each).*
Like Chuck said, use a 24" piece of 1/2" EMT conduit to sleeve over the wires. Also you can use a hose clamp to fasten on the outside of the shaft' This would give you a great line to follow when sawing that shaft and a good straight cut. Great video.
Great video. But I would personally get a metal tube that is slightly smaller than the shaft, put the wires through the tube and then feed it "into" the shaft opening, put the shaft on a vice, and then cut the shaft with a hacksaw. Much easier. :)
If you use a tubing cutter to cut down the shaft, you do not have wo worry about cutting any wires and it makes a nice clean cut. Since it is plastic and thicker than tubing it takes a bit more turning of the cutter to get through the plastic, but worth it.
Great video. Super helpful. Shots and explanations very clear. Bought a Minn Kota for my one man pontoon and the shaft is too tall to use comfortably. This is exactly what I was looking for.
Be careful, all your small bits of metal will end up in the armature or brushes of the motor ...maybe you could arrange the motor to be above when you drill the hole....great video!
I bet one of those rotating pipe cutters would work even better to cut that. I have a motor in the garage I need to shorten, might try the pipe cutter to see if it works.
I thought about that too in case I wanna make it bigger later for a different boat or whatever I have that option I was wondering if the tube disconnected from the bottom portion of the motor I would like to see that if possible
I liked the technique and was curious about your oneobjective cap mentioned but never shown. Then I went to your store and could not find it either. Also, it looks like you have some interesting fishing accessories...like a hook holder/line protector for rods, but that page is not active. A little feedback is my best way to pay you back for the info.
I tried cutting mine with a pipe cutter, to avoid hitting the wires, and it was not a clean cut, now my motor head is a bit loose. I may have to cut it shorter using this technique.
@@OneObjective you actually do not show it, the video ends after you cut the shaft and there is no reassembly and no hole for the screw that goes thru the shaft so its a bit confusing how it would go back together
May I ask folks....is there a performance reason to shorten the trolling motor length? I do understand the longer shaft can result in the motor head gettting in the way of me on the kayak, etc...but is there another reason to shorten the shaft? Thanks!
Thanks for the tip. I'm mounting a 50 lb thrust Minn Kota to the back of my NuCanoe F-12. I have the transom mount installed. How long should the shaft be using your measuring method, to optimize this motor to my Frontier 12? Also, what battery would you recommend? Thanks again.
just slide a pc of copper tubing over the wires and use a fine tooth hand saw or jig saw with fine tooth blade to cut it, but I guess both methods work fine. thanks for the vid.
A smaller diameter metal pipe also works great to protect the wires. Just push the wires through the metal pipe as you insert the pipe into the trolling motor shaft. It keeps them safe as you cut the shaft. Also best to have the motor upside down to keep debris from falling down into the motor.
*Great little trolling motor **enjoyable.fishing** recommend had it hooked up to my 15 foot old town canoe and it pushed it pretty good with me and my son (220 pounds each).*
Use a wood dowel, zip tie wires to dowel and push wires down pass the cutting point, cut shaft and wood dowel.
Excellent thanks exactly what I need to modify my trolling motor to suit my needs. Greetings from New York.
Like Chuck said, use a 24" piece of 1/2" EMT conduit to sleeve over the wires. Also you can use a hose clamp to fasten on the outside of the shaft' This would give you a great line to follow when sawing that shaft and a good straight cut. Great video.
Great video. But I would personally get a metal tube that is slightly smaller than the shaft, put the wires through the tube and then feed it "into" the shaft opening, put the shaft on a vice, and then cut the shaft with a hacksaw. Much easier. :)
Smart idea, thanks for sharing that...
If you use a tubing cutter to cut down the shaft, you do not have wo worry about cutting any wires and it makes a nice clean cut. Since it is plastic and thicker than tubing it takes a bit more turning of the cutter to get through the plastic, but worth it.
Thanks much, liked the way you got the wires out of the way.
Great video. Super helpful. Shots and explanations very clear. Bought a Minn Kota for my one man pontoon and the shaft is too tall to use comfortably. This is exactly what I was looking for.
Glad we could help
A pipe cutter would be fine to use without risking cutting the wires.
Man that was great!! I’ve been wondering how to do that when I put a trolling motor on my Kayak 👍👍 you did a nice job on it 👏👏👏
Thanks for watching! We have a few more installs coming. Stay tuned
Hi, do the black and red wires coming out go to the battery or pwm. What are the yellow and white wires for?
Purpose of the yellow and white wires? Reason being I'm fabricating a pool vacuum "riptide" style and want to use the motor from a trolling motor.
I feel like one of those tube cutting tool that you screw in and twist the blade 360 until you cut the tube would make this so much faster and easier.
Dang man, thanks... I've been scrambled on b how to get mine cut down, certainly didn't wanna by a short one when I have a great Minn Kota already..
Pipe cutter. Home depot
That's great, but I need to know how to cut down a MotorGuide that has a split shaft I think you call it?
Be careful, all your small bits of metal will end up in the armature or brushes of the motor ...maybe you could arrange the motor to be above when you drill the hole....great video!
It’s plastic
I bet one of those rotating pipe cutters would work even better to cut that.
I have a motor in the garage I need to shorten, might try the pipe cutter to see if it works.
Yep I’m sure it will
Try using a copper pipe cutter do you don’t need any power tools to cut the shaft down and you don’t need to protect the wires with anything
Hi friend! good video. Can you replace the original shaft and put a shorter one to avoid cutting?
I thought about that too in case I wanna make it bigger later for a different boat or whatever I have that option I was wondering if the tube disconnected from the bottom portion of the motor I would like to see that if possible
Kids got some pipes on em
😂
Thanks for the video, sure would like to have seen you install the cap so that we can see the benefit of the item.
hey, what did you do with the excess length of head cables please?
Did you also shorten them or other?
Thanks.
I can use tubing cutter to cut only out side metal part without touch those wires.
Me and my buddy did one on a MinnKota 45 Edge
Great video very helpful
I liked the technique and was curious about your oneobjective cap mentioned but never shown. Then I went to your store and could not find it either. Also, it looks like you have some interesting fishing accessories...like a hook holder/line protector for rods, but that page is not active. A little feedback is my best way to pay you back for the info.
I tried cutting mine with a pipe cutter, to avoid hitting the wires, and it was not a clean cut, now my motor head is a bit loose. I may have to cut it shorter using this technique.
how can i aquire one of those caps good idea on the shortening
We have them on our website. oneobjectivebf.com
How do you put the head back on?
We show you in the video. Its very easy
@@OneObjective you actually do not show it, the video ends after you cut the shaft and there is no reassembly and no hole for the screw that goes thru the shaft so its a bit confusing how it would go back together
Nice and easy
Then do u put the head back on
Yes can. Or a custom cap depending how you are rigging your motor
May I ask folks....is there a performance reason to shorten the trolling motor length? I do understand the longer shaft can result in the motor head gettting in the way of me on the kayak, etc...but is there another reason to shorten the shaft? Thanks!
No you don’t have to shorten it it’s up to you.
@@OneObjective Thank you very much for your reply! I've watched a bunch of videos, and figured I was missing something.
It's mostly for looks. but if your going to be relocating the controls there is no reason to have it so long.
Thanks for the tip. I'm mounting a 50 lb thrust Minn Kota to the back of my NuCanoe F-12. I have the transom mount installed. How long should the shaft be using your measuring method, to optimize this motor to my Frontier 12? Also, what battery would you recommend? Thanks again.
just slide a pc of copper tubing over the wires and use a fine tooth hand saw or jig saw with fine tooth blade to cut it, but I guess both methods work fine. thanks for the vid.
Use a pipe cutter and no protection needed.
Could’ve just get a tube cutter which would been better and faster that way you don’t have to be afraid of cutting the wires
I have to do this for my crappie brakes
Good deal.
pipe cutter to cut shaft
Use a small pipe cutter , much easier and safer
Could the shaft be shortened to 20 inch?
Yes it can
@@OneObjective I have an inflatable kayak, do you think 20 inch shaft would be enough for the motor to by fully submerged? (Am new to this)
use a copper pipe cutter next time , you won't have shavings go down into your shaft
😂
all that shit is falling down into your motor
Put a rag in there or something if you are concerned about it. But we have been doing for years with no issues
For the love of god file your hole so the wires dont cut. lol good job otherwise.
Was not impressed by handy-work. Reminds me of your fishing skills.
😂
@@OneObjective This man tried to fight me at boat ramp one time and lost.
Screaming children