ฝัง
- เผยแพร่เมื่อ 19 พ.ค. 2024
- 3D Printed RC Race Boat!
This is a fun project. I did a test run and it was fast and fun. Unfortunately it was windy and choppy so I did not get a good video. I will release a test run video after the winter!
0:00
0:15 Finding the STL
0:36 3D Printed Parts
0:53 Sanding and Gluing the Parts
2:49 Prepping Surface for Paint
3:27 Glazing Putty
3:59 Epoxy Coating
5:29 After Epoxy Coating Has Cured
5:44 Filling Imperfections Before Paint
6:49 Hardware
7:04 Measuring for Motor Mount
7:33 Drill Hole for Drive Shaft
7:51 Install Rudder Assembly
8:23 Epoxy Drive Shaft in Place
8:31 Prep Surface for Motor Mount
8:42 Epoxy Motor Mount in Place
8:59 Install Servo
9:08 Finished Boat Ready for Test Run
9:26 First Test Run Coming Soon!
STL can be found here: www.thingiverse.com/thing:245...
Designed by thepael
Parts I used -
Brushless Motor & ESC: www.amazon.com/dp/B095GNR1N2?...
Flex Collet: www.amazon.com/dp/B09K3HGTZ5?...
Propeller: www.amazon.com/dp/B07JQL6LYY?...
Lipo Batteries: www.amazon.com/dp/B07Y56XHMK?...
Rudder & Drive Shaft: www.ebay.com/itm/173865062345
Motor Mount:www.ebay.com/itm/222902551317... - แนวปฏิบัติและการใช้ชีวิต
Turned out really nice. Good job!
Thank you! It was a fun project. Working on another one now.
Nice one. Just printing the same boat. Some good tips, thanks.
It is a fun build!
Fantastic. Great job
Thank you!
You make good job.
Thank you!
Beautifull work!
Thank you!
I really enjoyed this video... greetings and support again my friend👍good
Thank you!
great job!
Thank you!
Looks Great? What did you use to mount your servo and ESC?
Thanks! I just used Velcro to mount them both. That way I can easily remove them when needed. I also swap them into other projects sometimes.
just printed and assembled the boat. do you have the measurements where you drilled the home for the shaft? im not into rc boats at all, so have no starting point.
Great project,if you whill build another one put one layer of fiberglass or carbon inside not only resin,and maybe twin motors whill be nice🙂
Thanks for the tips! I am going to build a bigger one next. Dual motors for sure!
@@bchobby believe me it whill be something amazing,I hit the🛎
@@bchobby th-cam.com/video/mFusbGBdp5Q/w-d-xo.html that's a twin 😉
That is awesome! I just subscribed. Very cool channel!
@@bchobby thanks,yes a nice hobby I like to build my boats🙂
What would you charge for a 46" cat hull with canopy shiped in pieces ready to assemble?
Hmu
Nice build! I have a similar build on my channel with the jet boat from thingiverse.
I didn't use any resin to cover my boat but in hindsight maybe I should have. Did it add noticable strength ? Are you worried the resin will separate and crack off the plastic or does it bend enough not to do that?
Thank you! It was my first 3D printed boat. I just know PLA will absorb water so I wanted to coat it. I have seen others coat it in carbon fiber. As for it delamination I have not had any problem yet. Waiting for winter to end before I can do some real testing.
Your channel looks awesome! I just subscribed.
@@bchobbyThanks. I did the same. I look forward to your next builds.
How this did you make your walls. I just finished printing mine and worried to sand a lot on it I made mine 1.2mm thick
Awesome but where did you find the file for the trailer??
Thanks! I got it on cults3d. I had to modify the length a little bit. Here is the link.
cults3d.com/en/3d-model/various/blackjack-catamaran-boat-trailer
I have a build Video of the trailer coming soon. But the designer has great documentation.
Will you print for customers
I am not sure it would be very cost effective for the customer but it is possible.
Is there 24” STL file for the Blackjack 24-Inch Catamaran Brushless: R?
I am not sure if there is a 24" version. You could probably just scale it down in the slicer.
I omitted one section to make it shorter
Ur boat is gonna explode, it looks really weak
I have about 10 batteries through it so far. No problems whatsoever. If it does break I will build a new version tougher next time.
@@bchobbynot sure how it looks weak, you coated it with epoxy, same way full scale cigarette boats do. Lol 😂
@@TheGreatBooger I agree haha! I am no expert though. This is my first attempt at a 3D printed RC boat.
Didn't mind the video except there's no talking and it just stupid music
Thanks for the feedback!
So lame.