The Vector Texture Tool - Part 50 - Vectric For Absolute Beginners

แชร์
ฝัง
  • เผยแพร่เมื่อ 8 ธ.ค. 2024

ความคิดเห็น • 25

  • @edayers315
    @edayers315 3 ปีที่แล้ว +2

    Hey "Stash", I've watched the 49 previous tutorials, "THANK YOU"!!!!!

  • @IceCreams62
    @IceCreams62 4 ปีที่แล้ว +1

    Very informative video, Mark, thanks a lot

  • @richardpoulin2947
    @richardpoulin2947 4 ปีที่แล้ว +1

    Thanks Mark you just chalenge me to get into new projects! your explanations are so clear, can't wait to try it. See you this afternoon..

  • @eCabinetstipsandtricks
    @eCabinetstipsandtricks 4 ปีที่แล้ว +3

    Thanks, Mark. I have wondered if it would be possible to create a textured tool path that could be used to simulate cedar shake shingles that could be used on a birdhouse or feeder roof for example.

  • @petergamache5368
    @petergamache5368 4 ปีที่แล้ว +1

    I've owned Aspire since version 8 and I don't think I've ever used this feature... Thanks for the demo!

  • @squidskunk
    @squidskunk 4 ปีที่แล้ว +2

    in your demo if you pocket the background to create raised text then texture the background that's when the diameter of the bit becomes a problem as the texture toolpath meets up to the text border....cuts into the edges of the text....create an offset around the text then texture to the offset and not to the text vector itself.

    • @MarkLindsayCNC
      @MarkLindsayCNC  4 ปีที่แล้ว +1

      Excellent point! That's what I should have done for the demo. I just ran out of time.

  • @jonathandehors2684
    @jonathandehors2684 4 ปีที่แล้ว +3

    Thank you for such an invaluable, incredibly executed series. You’re amazing. I’ve looked but was wondering if you have a video on doing an inlay? I’d really like to see your explanation over any others.

    • @MarkLindsayCNC
      @MarkLindsayCNC  4 ปีที่แล้ว +2

      Thank you very much, Jonathan! I don't have any videos on inlays yet, but they're coming later in 2021!

    • @jonathandehors2684
      @jonathandehors2684 4 ปีที่แล้ว +1

      Thanks!! Can’t wait

  • @liambuffat3731
    @liambuffat3731 4 ปีที่แล้ว

    I really enjoy your amazing collection of tutorials. I have an interest in 3d animation and woodworking which I suspect is similar to your interests. I sense that there may be an advantage to lying to v carve or your cnc in order to achieve certain goals. Say you want to v carve with a 60 degree bit that ends up too deep to achieve your goals. Perhaps you could set your zero at a higher level. Maybe there are other examples of work arounds that you have discovered. Anyway thanks for making a complicated subject a little easier.

  • @aaronhansen9909
    @aaronhansen9909 4 ปีที่แล้ว +3

    Thx mark, I would like to see how folks make a wave flag.

    • @johnsautier2703
      @johnsautier2703 4 ปีที่แล้ว

      I second that request

    • @chrisleech1565
      @chrisleech1565 4 ปีที่แล้ว +1

      check out SpindleTV. Think I saw a recent thumbnail. Nice, short and to the point :-)

  • @btreichel5
    @btreichel5 4 ปีที่แล้ว +1

    Hey Mark, how about some feeds & speeds, etc. Go out to the shop and show us whats you talk about when you say 'chatter, etc". Also how about some stuff about material (and bit?) selection. aka some are stringy, some are brittle.

    • @MarkLindsayCNC
      @MarkLindsayCNC  4 ปีที่แล้ว

      A soon as the temp drops down enough to get into the shop and work, I plan on doing some of what you're talking about. With shop temps sitting at slightly over 120°F (48°C,) it's not going to happen anytime soon. Computers don't like those temps, and neither do I.

    • @btreichel5
      @btreichel5 4 ปีที่แล้ว +1

      @@MarkLindsayCNC Neither do I. Use those extra amps in the new shop for a little AC. Us fat retired guys need / deserve it.

    • @MarkLindsayCNC
      @MarkLindsayCNC  4 ปีที่แล้ว +1

      That's the plan, brother - and one of the reasons for those extra amps.

  • @michaelturner3891
    @michaelturner3891 4 ปีที่แล้ว +1

    A note for the texture toolpath: When a tool moves in Z as well as X and Y, the effective speed will be the least of the feed speed or plunge feed settings for the too. So if the feed is 100 ipm and the plunge is 20 ipm, the tool will only move at 20 ipm even though you believe you have set the feed for 100 ipm.

    • @MarkLindsayCNC
      @MarkLindsayCNC  4 ปีที่แล้ว +1

      Excellent point, Michael! I've mentioned that many times in the past, but I did forget to mention it in this video. Thanks for checking it out!

  • @Aarononautos
    @Aarononautos 4 ปีที่แล้ว

    Just FYI, it sounds like this isn't available in Vcarve Pro, but it is. Just the way it was presented in the beginning.

    • @MarkLindsayCNC
      @MarkLindsayCNC  4 ปีที่แล้ว +1

      This is a transcript I just wrote up, taken directly from the video:
      "The Vector Texture Tool itself is available in Cut2D, both Desktop and Pro, VCarve Desktop and Pro, and Aspire.
      This portion of this video applies to all three. However, when we get over here to the Texturing Toolpath itself, that is not available in Cut2D Desktop or Pro."
      If you took that to mean it's not available in VCarve, I'm sorry for the confusion. I did clearly say that it IS available in VCarve Desktop and VCarve Pro. Thanks for keeping me on my toes! This is how I work harder to make sure I get it right!