The arm that is attached to the frame should be at 90 degrees for this type of mount. I suspect that you didn't measure anything according to the directions in the box. The distance from the center of the hinge pin to the first hole of the closer and subsequently to the first hole of the shoe is specific and if not correct can make the door not open fully, open too much or take too much force to open the door. Also the distance of the closer to the top of the door is quite specific so the arm doesn't hit the door.
Hey Jim, my main door of the house is quite heavy and we have installed a door closer on it. We have also installed a door magnet as a future possibility of keeping the door in open position. But with door closer, the door magnet is not able to hold the door. Any suggestions for installation?
@@monalisadas6919 If the magnet is installed correctly it should hold the door in the open position. However you could install a "hold open" door closer arm on the existing door closer instead of the magnet. That would be a better solution unless the magnet is tied into a fire alarm and releases to shut the door electrically.
;) it just doesnt work upside down, it hits the side of the hydraulic system... p.s. a lot of systems have regulatory arms where you would not run into problem like yours: example image: 4.imimg.com/data4/VE/YV/MY-3634223/door-closure-500x500.jpg
According to the manual adjusting the screw on the side will get it done. But in my experience, you should remove the nut that holds the door to the mechanism. Then close the door. Wait for sometime to let the spring inside the mechanism fully unwind. Then attach it back to the door.
That is incorrect. If the door closer has a power adjustment (some cheaper ones do not) then it is a spring tension screw located on the opposite end to the sweep and latch adjustment screws on these imports.
I know this reply is old but these models with the offset pivot on the main housing all, even to this day, are difficult to open. The angles have little to no effect. The ones currently on Amazon are also difficult to open. EVEN WHEN YOU USE THE ENCLOSED TEMPLATE TO DRILL THE HOLES AND MOUNT THE BRACKET AND BODY IT WILL STILL BE HARD TO OPEN. If anyone reads this my advise is to spend a few more dollars and get one from Grainger or a model that Grainger sells. It's just a piss poor design. Shame because the material/metal is quality stuff.
You can usually adjust the power spring on the end of the closer counterclockwise to make the door easier to open. Some inexpensive closers do not have this adjustment.
I am sorry to say this is not the proper way to do that. You mentioned the catalogue that came in the box and it shows the installation for left and right sided doors. You simply need to use the drawing to mark where to fix the 6 bolts. In your way a lot of adjust will be needed and most probably will not work, but using the catalogue no adjust will be needed.
In the door closer assembly the part which is installed on the frame..it should be of Aluminium or wood..? k it can also be applied on the wall diectly..?
just use a metal drill bit they are really cheap dude, its exactly like drilling wood or concrete, maybe you just need to go slightly slower and not press alot.
You clearly don't do this for a living, by not putting a pre load on the arm you loose your proper Las couple of inches of power, remove the arm from the closer, rotate the arm parallel to the door, take a wrench on the bottom of the closer and turn it to put a little bit of a load on the arm , by have the arm pointing out will some what work except for the last few inches.
The closer arm needs to be connected to the body in a position that is diagonal from the body instead of perpendicular. So that when you connect the closer arm to the door frame, you have to fight the spring tension of the arm a little bit to get it to screw into the door frame. Once it's connected, the arm should be almost perpendicular to the door. I use this description to make it easier to understand that you're putting load on the arm so that it has pressure even when the door is closed. You are connecting the arm to the body in an offset position, then winding it only a bit, then you screw it to the door frame with that resistance. I use the adjustment screw on the arm by loosening it, extending the arm, screwing the arm into the frame, push the elbow of the arm until it is mostly perpendicular to the door in the closed position, then tightening the adjustment screw down so that the arm doesn't extend when i let go of it. The goal is to have a door that shuts and latches entirely, rather than the door that closes almost all of the way until the arm relaxes and it stays cracked open.
Boht Aache majne aapke videos Dekh Kar 100 pcs 3 din mai kaga diya Thank You So Much
Aapi Video Boht UseFull Hai
Thank you
The arm that is attached to the frame should be at 90 degrees for this type of mount. I suspect that you didn't measure anything according to the directions in the box. The distance from the center of the hinge pin to the first hole of the closer and subsequently to the first hole of the shoe is specific and if not correct can make the door not open fully, open too much or take too much force to open the door. Also the distance of the closer to the top of the door is quite specific so the arm doesn't hit the door.
Very basic the guy has no clue about it & 99 percent door closer user do not see the manual which confirms the 90 degree angle !
Appreciate it smart guys...maybe yall can come out with videos on how to put doors in.
Pp
Hey Jim, my main door of the house is quite heavy and we have installed a door closer on it. We have also installed a door magnet as a future possibility of keeping the door in open position. But with door closer, the door magnet is not able to hold the door. Any suggestions for installation?
@@monalisadas6919 If the magnet is installed correctly it should hold the door in the open position. However you could install a "hold open" door closer arm on the existing door closer instead of the magnet. That would be a better solution unless the magnet is tied into a fire alarm and releases to shut the door electrically.
Outstanding video to you sir! I have problem with same issue on door. This fixed my issue.
well done, and nice touch showing a mistake like in real life...who does that? lol.
It can be use both side ? Right and left door?
1:45... you also placed the hinge upside down.
It was because of the space constraint. But thanks for noticing.
;) it just doesnt work upside down, it hits the side of the hydraulic system...
p.s. a lot of systems have regulatory arms where you would not run into problem like yours: example image:
4.imimg.com/data4/VE/YV/MY-3634223/door-closure-500x500.jpg
Veri good, Teatcher, congratulations
Fantastic explanation! Can't wait for your next video on this topic!
Thank you!
Excellent pace on video. Concise narration. Exactly what I needed. Thank you, from new home owner.
Can it be installed vertically? To a door that opens 180 degrees from top to bottom?
Nope
The arm attached to the door frame should be perpendicular to it for maximum efficiency.
Thanks so much and before watching this video was a nightmare and I couldnt install it by myself & now I fixed it; it also works well
how can we adjust the pressure while opening the door... I I have the same (royal) I feel very hard to open the door...please reply me
According to the manual adjusting the screw on the side will get it done. But in my experience, you should remove the nut that holds the door to the mechanism. Then close the door. Wait for sometime to let the spring inside the mechanism fully unwind. Then attach it back to the door.
That is incorrect. If the door closer has a power adjustment (some cheaper ones do not) then it is a spring tension screw located on the opposite end to the sweep and latch adjustment screws on these imports.
I know this reply is old but these models with the offset pivot on the main housing all, even to this day, are difficult to open. The angles have little to no effect. The ones currently on Amazon are also difficult to open. EVEN WHEN YOU USE THE ENCLOSED TEMPLATE TO DRILL THE HOLES AND MOUNT THE BRACKET AND BODY IT WILL STILL BE HARD TO OPEN. If anyone reads this my advise is to spend a few more dollars and get one from Grainger or a model that Grainger sells. It's just a piss poor design. Shame because the material/metal is quality stuff.
Does it work as a stopper too?
Is it supposed to be a door closer or can it work alternatively. That's stopping the door from closing automatically
thanks for also sharing the common mistake.
good tutorial.
Thanks :)
PJ Sinohin vvvvvvv
Great...to see you did wrong delebratly...and then done right...i am sure now one fix it wrong after watching this vedio...Thanx
Let's say i want to lighten the force required to open the door (inward pull, hinge on the right). Do i move the machine towards the hinge or what?
You can usually adjust the power spring on the end of the closer counterclockwise to make the door easier to open. Some inexpensive closers do not have this adjustment.
After fixing , the door is so stiff. Any adjustments
mine works great but the spring creaks when opening ... any idea why and what i can adjust ? Thanks
Royal Company ka keha pe mile ga ji price kyaa hai sonipat haryana
Can it be installed on the opposite side of the door?
It has to always be installed on whatever side the henges are....
What's the model number or product moniker of this particular Royal door closer? Thanks..........
Michael LoVetere ,,hai sir u should need int'l brand: DORMA, md:23.
Just check at your local hardware store. Anything is fine.
Does it also require lubrication?
Tx. U saved me money and my marriage. We could not figure the thing out. One view and it was sorted
Ha ha ha!!
You’ve got bigger problems if a self closing door tutorial saved your marriage...
Simple and easy to understand tutorial. Well done.👍
This guy teaching how to put door closer doesnt know how to put door closer the right way. But it works.
How to keep the door opened for the daytime?
while opening my door, arms are coming little down and toching door...i think something is wrong...how can i repair it..??
will it work for steel doors?
I am sorry to say this is not the proper way to do that. You mentioned the catalogue that came in the box and it shows the installation for left and right sided doors. You simply need to use the drawing to mark where to fix the 6 bolts. In your way a lot of adjust will be needed and most probably will not work, but using the catalogue no adjust will be needed.
I did not have to adjust. It worked by itself
In the door closer assembly the part which is installed on the frame..it should be of Aluminium or wood..? k it can also be applied on the wall diectly..?
It can be anything as long as you can drive a screw into it.
Sir it will use for plastic door
What mechanism is used in this one..any one please reply me.
Mechanism??
What happens if we push the door hardly while closing
Thank you so much i love India 🇮🇳 ♥️😻
Very helpful, Thank you !
Ok
Good
Thanks for sharing!
Thanks for watching!
Como ponerle precio o repararlos
They are cheap. It’s better to replace it
I can almost understand the spoken language. Thanks for the subtitles.
What is price
This door closer is not good aluminum I bought 8dorcloser and all are creating noise when doror closes
Just grease it with WD
Very helpful thank you
So glad!
Thank you for the video. Is it the closure or door hinges squeaking.
The hinges.
very helpful , tnx !🔩🔧🔨
How to drill into metal frame? Thanks
You can use HSS drill bits. That can drill into metal frames.
just use a metal drill bit they are really cheap dude, its exactly like drilling wood or concrete, maybe you just need to go slightly slower and not press alot.
Do I need to insert wood/plastic plugs into the metal hole? or just directly screw in the screw into the metal hole?
What if I directly screw in the screw and the screw seems quite loose?
There are self tapping screws for metal work. You can use them to screw in directly to metal.
ouuuu I see ... my worker put the door closer in the wrong side ... LOL.... Nice video Ty!!
Attention! The 90 degree angle is incorrect! Such an angle should not be at the lever, but at the thrust!
Thank you for the information
How much it
This is extremely superb
Good video friend
Well done instructional video
Thank you
Thanks very useful
thank you!
Than.kyou very much..
How to adjust speed
Merci👍
How to you repair sir
price
Rs.800
sir thanks for the good explanation and good method of fitting
Thank you!
Now I got extra holes on my door frame exposed what are you gonna do about it I’m a customer and I’m questioning that…….
Very good
We learned from you sir.Thanks.
Very nice
Thanks for uploading
01:49 Oh ohh! It doesn't match!
Yup. But fixed it.
Nice work bro
ओपन करने में टाइट है तो क्या सेटिंग करे
Nice trick
You clearly don't do this for a living, by not putting a pre load on the arm you loose your proper Las couple of inches of power, remove the arm from the closer, rotate the arm parallel to the door, take a wrench on the bottom of the closer and turn it to put a little bit of a load on the arm , by have the arm pointing out will some what work except for the last few inches.
Yes I dont. Figured it out as I went. Can you make a video and show me?
Kalaakaar // Custom Fabrication Channel you betcha
Good video
Provide the provided providings
common mistake was really helpful. thanks
I am glad you liked it.
Amazing fidio, fankyou for the anazimg tutorial.
Good video and presentation. Thank you.
Thanks :)
Nice
Tq
Thank you very
very love wideo. when more are come?
sir you
I upload two videos a week
My mom, sis always leave my room door open thats the reason i want one door closer 😂
But why measurement why I don't like show your measurement okay
नमस्ते , ऐसे तो थोडे ही दिन मे ढिला हो जाता है।
Quiero saber el precio
Vare nice I do Work in dubai for Alumonimm gless and door Caluding
thank you sir
No Problem.
Thanks
2:45 is annoying horror movie
Ha ha ha... Good one.
ممتاز شرحك
وش فهمت منه
اشرح لنا لو تكرمت ابغى شرح عن التركيب
You Didn't Pre-Load The Closer!
+rissone99 what is that?
+Kalaakaar // Custom Fabrication Channel 9116783101
The closer arm needs to be connected to the body in a position that is diagonal from the body instead of perpendicular. So that when you connect the closer arm to the door frame, you have to fight the spring tension of the arm a little bit to get it to screw into the door frame. Once it's connected, the arm should be almost perpendicular to the door. I use this description to make it easier to understand that you're putting load on the arm so that it has pressure even when the door is closed. You are connecting the arm to the body in an offset position, then winding it only a bit, then you screw it to the door frame with that resistance. I use the adjustment screw on the arm by loosening it, extending the arm, screwing the arm into the frame, push the elbow of the arm until it is mostly perpendicular to the door in the closed position, then tightening the adjustment screw down so that the arm doesn't extend when i let go of it.
The goal is to have a door that shuts and latches entirely, rather than the door that closes almost all of the way until the arm relaxes and it stays cracked open.
I need this because, I have siblings.
Lol
thanks
wtf..... the door closes very slowly............
1:15 be sure to check the diagram!? Dude I'm watching this because i don't want to check the diagram!
More over, i don't have a diagram!
Shekaran Jag Google it. If you can't find a PDF online then that's on you for buying cheap no-name brands.
😂😂😂😂😂 i blame that on amazon for sending me cheap stuff
messy job - you can't even fix a door stopper properly
Thank you :)
It's called a fire door we have them all the time
โช้คกันหน้านถสปัดอย่ามาหรอกให้ยาก
That intro is terrible. Glad I had my speakers turned up so loud at 3 a.m. Thanks.
How to close a door 😂😂😂
nice
+LAST GAMER OF WORLD thank you