Como mecânico não vejo nada que esteja sendo feito de errado no vídeos o precedimento de plaina do bloco pode ser feito de várias formas, a retifica utiliza equipamentos profissionais para isso. Não significa que usando outro tipo de técnica não fique bom. Tanto que ele está a testar planicidade para corrigir o empeno.
Это где это так притирали? В Австралии аборигены? Мне 43года и батя отдавал блок и голову на станке шлифовать плоскости, когда мы на жиге мотор капиталили, я ещё в школу не ходил. И это, минуточку в Новосибирске было, в западной Сибири
One issue, that’s the Engine Block not the cylinder head. For anyone asking what’s the red stuff? That’s marking paint, what’s being demonstrated here he’s showing how warped the block deck is. Using a machined flat aluminum or steel block with the marking paint you can see dips or raised areas that were warped by the engine over heating. The spots that the paint didn’t get on, could create a gap big enough that the gasket won’t seal it.
@@doroningames3893 это уже дело хозяина или чистоплотности мастера, читал, что после шлифовки коленвала мастера отдают заказчику без чистки и промывки каналов, клиент не зная о такой подставе собирает и радуется забитым масляным каналам и новым проточкам на валу))
В 2019 году знакомому делал подобным способом. Изначально блок уже был приговорён к замене. Купить можно было только столбик в сборе за 400$+... Прокладки под головой у него пробивало каждые полгода, ездил к разным "мотористам" и никто не проверял плоскость блока, кидали новую прокладку и шлифовали ГБЦ. Я отшлифовал плоскость блока, продул и промыл все каналы, собрал всё. Три года он точно после этого отъездил, дальше не знаю. А по факту, он должен был уже ДВС сменить. P.s. всё делалось только при снятой ГБЦ, двигатель с авто не демонтировался.
All the internet mechanics here. I've done it this way forever and never have a problem. If it's an old high mileage car, nobody wants to pay to remove the whole engine and have the block sent off and refaced. Just make sure to blow away all the swarf when you are done.
He is not getting a proper grind this way. He is stopping mid stroke, because the engine is in the car. This is not a good way to do this. It'll be a fix, for a while. But that head won't sit straight.
you do this for 30 years and you worry about dirty piston rings clearly you have no idea what your talking about and yes that is a bad thing but what is even worse is the oil gally is XD taking more junk in then your piston rings and wich you can suck most of the crap out with a vaccume when it comes to the piston rings but the oil gally xD it will stick in every corner and cranny you can find this will kill the engine in matter of miles or kilometers
то есть для замены прокладки гбц разбирать полностью двигатель? Так никто не делает. Блок цилиндров так и шлифуют, если снимается только ГБЦ, только поршневая система закрывается. Правда шлифуется не такой приблудой, а чисто снять все дерьмо. что бы прокладка легла хорошо
Каждый раз так делаю при замене масла. Главное, после сборки продуть от опилок воздухом через свечные отверстия, а в бак добавить полведра комрпессии для хорошего первого запуска. Совсем забыл, что в свободной продаже компрессии не найти, поэтому нужно будет уточнить её наличие у знакомого моториста.
У твоей собаки глисты завелись. Возможно она и тебя ими наградила… Сходи до врача проверься, а то самому придется ездить задом по траве как твоя собака…😂
По мимо того что масляные каналы будут наполнены абразивом, применение поверочного инструмента производиться не верно. Хотя даже такое применение показывает что кустарная шлифовка блока цилиндров не привела к нужному результату. Необходимо подобные операции производить на высокоточных станках с ценой деления около 0,01мм
@@vadim454545 я с вами не соглашусь перекос в сотку критичен для гбц и необходимо использовать станки с такой точностью. В противном случае по мимо причины ремонта можно столкнуться с новыми неисправностями двигателя. К примеру педантичные немцы написали даже к каждой своей марке инструкции по ремонту своих двигателей в которых чётко указаны допуски перекосам и зазорам. А я, в свою очередь, осмелюсь предположить что инженеры что пишут эти инструкции далеко не идиоты. В моём случае такие станки найти не проблема. И ещё один аргумент в сторону моей правоты: при каждом снятии гбц необходимо шлифовать её, а как мы знаем в России ремонтируют даже не ремонтопригодное. Так вот если мы будем каждый раз счёсывать по десятке то через сколько раз кончится допуск по размерам гбц и блока?
Можно сделать ето руками , нужна поверочная плита перекрывающая плоскость блока и шабер. Такая процедура используется для ремонта станков, но ето жалкое подобие и брак
Sin los cuidados pertinentes, sería imprudente. Ahora si, previenes el ingreso de las virutas con trapo, algodón y grasa, va de 10. Ahorras muchísimo tiempo. Lo he aplicado, tanto en motos como autos y siempre con resultados excelentes (de mi propiedad). Entiendo que si fuera un trabajo para terceros, donde el cliente pone el dinero, desarmar medio vehículo repercute en él y los mecánicos, no tienen consideración en ello. Esa misma técnica se puede usar también para la tapa, la cual es, la que se mueve sobre una superficie perfectamente plana, plancha/tela de lija intermedio. Luego todo se controla. Sino tienes los medios para hacer el trabajo, la rectificadora es la opción.
Using a stone is a completely safe and dependable method if done properly with the correct stone, lubrication, technique and also for fuck sake plug the oil gallieries at a minimum.
You should NEVER do something like this unless the engine is completely removed and the block is entirely tore down and also inside of a cnc machine........
I mean, this is not the worst way I've seen. Engine in, ok. But those with the engine out, isn't it worth the few bucks to have the machine shop do it properly? When you're putting in all the other work?
First of all you put the Persian bluing or in this case the red stuff maybe hi-spot bluing just red since they make it in both colors. Anyway you put the bluing on the block or cylinder head smear it on there with something like wool. Then you slide The straight edge across it any spot that is shiny is your high spot. Doing it backwards like this just proves you can smear a few mil across the surface you could still be four or five thousands out add highly likely even more. Second you take modeling clay and make a snake press that down around the outside of the piston so that that fine grit doesn't fall down between the piston in the cylinder in the gap on top of the Rings then you stuf some damp rags down in there to catch the grit. Once you remove the rags you can then blow the rest of it out with compressed air but not enough pressure to blow the clay out of place. Better yet if you have an old set of Pistons without rings drop them down in on top of the good ones pack clay around them this way your contaminated cylinders that you have to blow out will not be as deep. Now you can take a flat file and on the flat end grind a radius about the size of a nickel. Then tip your grinder rest to about 10°sharpen one side of that in the same shape as a nickel to about center flip the file over and do the same on the other side now you have a hard scraper that will scrape off the high spots. Of course the ideal tool would be a carbide scraper but the file will work the same just a lot cheaper. The carbide scraper you would be looking for would be used for scraping in precision machines and yes they make them in a power scraper also but they are quite pricey for the average person.
Muy útil me párese. Los motores de ahora con bloques de aluminio y materiales de tan mala calidad al recalentarse se deforman los bloques y normalmente toca bajar y desarmar para hacerlo rectificar y dar planitud. Me he ahorrado mucho Tiempo y dinero al cliente desde q me ofrecieron el servicio de rectificado con el bloque instalado. Simplemente se tapan los orificios de retorno aceite y lubricacion.
Everyone worried about the shavings but not mentioning how out of plum the engine surface is. Id be more worried of the non-flat surface causing blow by before those little shavings I can blow with conpressed air.
At least take the engine out. What do you think will happen to piston rings even if they catch a little debris into the cylinders or oil and coolant passages
hello from France, not bad your tool! on the other hand wouldn't it be better to protect the pistons? because there they are not all going to like the filings at the first turn of the starter!
Head gasket is fixed but the engine is destroyed! Hint: prior to surfacing roll up strips of paper towel and stuff them into all passages to keep the metal & abrasives out of the engine internals. After surfacing is satisfactory remove all paper towel rolls from passages with a drywall screw while vacuuming then clean surfaces, apply copper coat. Perhaps using a larger surfacing block would also be beneficial. I've used a large file and had lasting results but I wouldn't recommend it.
Да Это не правильно никому не советую, но этот метод не плохо работает при должном подходе. И даже как то работает при подходе "на от@бись". Только трудозатрат обычно больше, чем снять и на плоскошлиф отвезти.
Here in Brazil we have a popular saying: what’s cheap can be very expensive…
Hookers?
Эта поговорка действует во всех уголках мира)))
How much did you save doing it twice?
В России говорят: Скупой платит дважды!)
Como mecânico não vejo nada que esteja sendo feito de errado no vídeos o precedimento de plaina do bloco pode ser feito de várias formas, a retifica utiliza equipamentos profissionais para isso. Não significa que usando outro tipo de técnica não fique bom. Tanto que ele está a testar planicidade para corrigir o empeno.
it's always a good thing to put shavings into the cylinders, helps to hone the walls
😂
True That
Not much you can do to avoid it, just gotta blow em out when you're done.
🤣🤣🤣
Это называется обкатка новые технологии)))
Главное потолще слой краски, тогда точно плоскостность в допуске будет😂
и линейку поперёк блока класть, тогда 100% успех
@@user-km5sb8uj7m😅😂😅😂😊
@@user-km5sb8uj7m и линейку обязательно плашмя 😂
Сам лично на м54 делал машина уже года 3 ездит 🤔
Это краска ямы смотрит
Станки до соток линейкой вышабривают
Hurts my eyes watching all that debree going in
Then wear safety glasses.
You def aint a mechanic or qualified to be even talking about this
надо к машине присоединить, и по асфальту пару километров проехать, а то так не точно получится, с зазорами
Умный спасу нет хотя совсем не давно так только и притирали
@@user-nn4ue3cp8oне правильно!
Это где это так притирали? В Австралии аборигены? Мне 43года и батя отдавал блок и голову на станке шлифовать плоскости, когда мы на жиге мотор капиталили, я ещё в школу не ходил.
И это, минуточку в Новосибирске было, в западной Сибири
One issue, that’s the Engine Block not the cylinder head. For anyone asking what’s the red stuff? That’s marking paint, what’s being demonstrated here he’s showing how warped the block deck is. Using a machined flat aluminum or steel block with the marking paint you can see dips or raised areas that were warped by the engine over heating. The spots that the paint didn’t get on, could create a gap big enough that the gasket won’t seal it.
Is he using sandpaper to sand the surface to be even and high?
Идеальный способ наполнить масляные каналы абразивными продуктами износа шлифовального приспособления.
Типа при фрезеровке стружка не летит в каналы, потом чистить и промывать все равно нужно будет, а прокладка должна заполнить микро щели
@@ivanschultz1987только тут шлифуют установленый двигатель сомневаюсь что его снимут чтобы продуть или промыть
@@doroningames3893 это уже дело хозяина или чистоплотности мастера, читал, что после шлифовки коленвала мастера отдают заказчику без чистки и промывки каналов, клиент не зная о такой подставе собирает и радуется забитым масляным каналам и новым проточкам на валу))
Это же не Автоваз. Они они ещё 10 раз перемоют этот движок...😜
@@doroningames3893скажи честно, ты конченый? Если его не снять и не промыть он после прогрева в хлам будет. Или ты типо умнее всех?
That's not the head refacing that's the engine block 🎉
Не дай бог попасть к такому мастеру
Отличный способ закончить блок😂
Пакистан текнолоджи
Да не, стружка, которая туда попадает, притирает весь двигатель))
В 2019 году знакомому делал подобным способом. Изначально блок уже был приговорён к замене. Купить можно было только столбик в сборе за 400$+...
Прокладки под головой у него пробивало каждые полгода, ездил к разным "мотористам" и никто не проверял плоскость блока, кидали новую прокладку и шлифовали ГБЦ.
Я отшлифовал плоскость блока, продул и промыл все каналы, собрал всё. Три года он точно после этого отъездил, дальше не знаю. А по факту, он должен был уже ДВС сменить.
P.s. всё делалось только при снятой ГБЦ, двигатель с авто не демонтировался.
All the internet mechanics here.
I've done it this way forever and never have a problem. If it's an old high mileage car, nobody wants to pay to remove the whole engine and have the block sent off and refaced. Just make sure to blow away all the swarf when you are done.
Dumb
Fr so many internet mechanics who've never even done the work.
Should use putty to keep the shavings from getting in the rings make it easy to clean after been doing this for 30 years and never had a issue.
Que es masilla
He is not getting a proper grind this way.
He is stopping mid stroke, because the engine is in the car.
This is not a good way to do this.
It'll be a fix, for a while.
But that head won't sit straight.
@@silvianoayuzo554
Clay or playdough.
😉
@martinnielsen5851 if he's using a soft graphite gasket it will be fine it will compensate the imperfection I don't think he's building a race engine.
you do this for 30 years and you worry about dirty piston rings clearly you have no idea what your talking about and yes that is a bad thing but what is even worse is the oil gally is XD taking more junk in then your piston rings and wich you can suck most of the crap out with a vaccume when it comes to the piston rings but the oil gally xD it will stick in every corner and cranny you can find this will kill the engine in matter of miles or kilometers
мне в этом видео больше всего понравился момент с замером готовой плоскости
Нужно было краски больше на мазать и шкурить не пришлось
😂😂😂😂 what a cowboy. You aren’t touching mine 😂😂😂
😂😂
Раз ты уже краской намазал, можешь смело ставить головку на старую прокладку.
Oh pero me parece muy precario éso no sé
@@josealvarez13он пошутил это был сарказм😂
@@user-yb5pj1pg9kнет не сарказм, а проверенный дедовский способ
Как не старайся, но есть станок для этого где всë точно и быстро.
то есть для замены прокладки гбц разбирать полностью двигатель? Так никто не делает. Блок цилиндров так и шлифуют, если снимается только ГБЦ, только поршневая система закрывается. Правда шлифуется не такой приблудой, а чисто снять все дерьмо. что бы прокладка легла хорошо
@@AndreDaniels-oc7xzBS
2 раза в день это упражнение делай, и мотор болеть не будет
Каждый раз так делаю при замене масла. Главное, после сборки продуть от опилок воздухом через свечные отверстия, а в бак добавить полведра комрпессии для хорошего первого запуска. Совсем забыл, что в свободной продаже компрессии не найти, поэтому нужно будет уточнить её наличие у знакомого моториста.
Моя собака задницей как то раз по траве на передних лапах проехала, такой-же слой герметика оставила 😂
При чем тут герметик
У твоей собаки глисты завелись. Возможно она и тебя ими наградила… Сходи до врача проверься, а то самому придется ездить задом по траве как твоя собака…😂
@@user-ig5eb8zo3y при том! тут в видосе всё прекрасно ,а каменты полны сарказма...
аааа. ты же не знаешь что такое САРКАЗМ...
Wytrzyj i przekrec o 90° ten prostokąt i wtedy połóż zobaczymy czy będzie wszędzie czerwone xDDDD
I tak nie bylo wszedzie. No ale glowica sie ugnie co cylinder pod szpilkami
Абразив в цилидрах необходим!!!
Ладно в цилиндрах, там полные маслоканалы
@@S-B1990а ты считаешь при хоннинговке нет опилок?
Цилиндрам будет весело от подкинутого им стружки.
По мимо того что масляные каналы будут наполнены абразивом, применение поверочного инструмента производиться не верно. Хотя даже такое применение показывает что кустарная шлифовка блока цилиндров не привела к нужному результату. Необходимо подобные операции производить на высокоточных станках с ценой деления около 0,01мм
Нолик лишний, 1 микрон 99% станков не поймают.
@@vadim454545 простите, ошибся. Отредактировал.
@@vadim454545не микрон, а сотка.
Самое главное чтобы станок ещё и обрабатывал с донной точностью.
@@vadim454545 я с вами не соглашусь перекос в сотку критичен для гбц и необходимо использовать станки с такой точностью. В противном случае по мимо причины ремонта можно столкнуться с новыми неисправностями двигателя. К примеру педантичные немцы написали даже к каждой своей марке инструкции по ремонту своих двигателей в которых чётко указаны допуски перекосам и зазорам. А я, в свою очередь, осмелюсь предположить что инженеры что пишут эти инструкции далеко не идиоты.
В моём случае такие станки найти не проблема. И ещё один аргумент в сторону моей правоты: при каждом снятии гбц необходимо шлифовать её, а как мы знаем в России ремонтируют даже не ремонтопригодное. Так вот если мы будем каждый раз счёсывать по десятке то через сколько раз кончится допуск по размерам гбц и блока?
Делаю 230 диском для ушм, проблем нет
Я вот так с помошью художественных красок в юнности подгонял знаки пресс-форм. Когда ещё работал на СИиТО.
Ths ia how a job like this should not be done...
Прикольно будет когда этот абразив забив сначала фильтр пойдет через перепускной клапан ко всем трущимся деталям
Name the tools you use to smooth the surface of the sea
Чем больше краски - тем ровнее плоскрсть😅😊
Put shaving cream In cylinders to capture particles then vacuum it out when done🤙🏻
Looks great actually
That’s how you supposed to return heads to your customers 😂❤😊
🤭
Cylinder liners need to be lil bit thicker to press the gasket harder so the combustion pressure won't go out to the water jacket
Можно сделать ето руками , нужна поверочная плита перекрывающая плоскость блока и шабер. Такая процедура используется для ремонта станков, но ето жалкое подобие и брак
Кто ж блок точит?- ГБЦ надо точить!!)😅
فكره حلوه واجهت صعوبه في التمييز المستواء الى ان لونت الراس بخطاط وجلست امسح الى انت اختفاء لون الخطاط🙂👋🏻
Great way to mess up a perfectly flat machined surface is to hand sand it
Orange silicone to seal the head gasket is the best way to do it 🤣🤣
дааааам, в моторе металлической стружки не хватает🤣🤣🤣🤦♂️🤦♂️🤦♂️
и весь образив в двигло, красавчик
Genial ... puliendo a mano = ojimetro !!!😅😅😅
"Lapping tool" we used them in the Navy for repairing valve gates and stems.
После такого капитального ремонта нужен будет ещё один
Весь образив в мотор летит,прикольно!😂
Ух ты! Нанотехнологии!!
Есть жидкие гвозди, а это жидкая прокладка!
Но на клей Момент лучше заходит, потом в процессе могут ещё идей возникнуть!!!😂😂
Мне интересно как он потом образив из масляный каналов выдувать будет?
Да зачем....? Так даже лучше будет.
компрессором, не?
@@Radovid_V_Svirepyy компрессоров ты абразив ещё глубже загонишь в масляные каналы
That is a block NOT a head......
Yo e utilizado esa técnica de cepillado, pero se tapa/protege los cilindros, metiéndole alguna tela o algo que evite que las virutas caigan dentro.
Apply a thin layer of dye separately then use a clean flat to expose higher points. You should be using a flat the same size as your workpiece.
Если бы огородить поршневую снутри,и закрыть масленный канал блока,было бы ваще чётко👍
Надо это делать пришабренной цельной плитой чтобы легла на весь разъём а не клинышком
Mala practica
Sin los cuidados pertinentes, sería imprudente. Ahora si, previenes el ingreso de las virutas con trapo, algodón y grasa, va de 10. Ahorras muchísimo tiempo. Lo he aplicado, tanto en motos como autos y siempre con resultados excelentes (de mi propiedad). Entiendo que si fuera un trabajo para terceros, donde el cliente pone el dinero, desarmar medio vehículo repercute en él y los mecánicos, no tienen consideración en ello. Esa misma técnica se puede usar también para la tapa, la cual es, la que se mueve sobre una superficie perfectamente plana, plancha/tela de lija intermedio. Luego todo se controla. Sino tienes los medios para hacer el trabajo, la rectificadora es la opción.
He still has a lot of sanding left !!!😊
Using a stone is a completely safe and dependable method if done properly with the correct stone, lubrication, technique and also for fuck sake plug the oil gallieries at a minimum.
« С пивом пойдет» раньше шлифовали вручную и ничего, ездили.
You MIGHT get the truck. You'll NEVER get the title. 🤙
You got that right!
You should NEVER do something like this unless the engine is completely removed and the block is entirely tore down and also inside of a cnc machine........
Wenn dann schleift schräge und Kreisend.......das üben wir noch Mal....😂
This works ive done it plenty of times
Overheat = I Got This 😈
Молодец 👌
Какой слой краски и все равно завалил 😂
I mean, this is not the worst way I've seen. Engine in, ok. But those with the engine out, isn't it worth the few bucks to have the machine shop do it properly? When you're putting in all the other work?
First of all you put the Persian bluing or in this case the red stuff maybe hi-spot bluing just red since they make it in both colors. Anyway you put the bluing on the block or cylinder head smear it on there with something like wool. Then you slide The straight edge across it any spot that is shiny is your high spot. Doing it backwards like this just proves you can smear a few mil across the surface you could still be four or five thousands out add highly likely even more. Second you take modeling clay and make a snake press that down around the outside of the piston so that that fine grit doesn't fall down between the piston in the cylinder in the gap on top of the Rings then you stuf some damp rags down in there to catch the grit. Once you remove the rags you can then blow the rest of it out with compressed air but not enough pressure to blow the clay out of place. Better yet if you have an old set of Pistons without rings drop them down in on top of the good ones pack clay around them this way your contaminated cylinders that you have to blow out will not be as deep. Now you can take a flat file and on the flat end grind a radius about the size of a nickel. Then tip your grinder rest to about 10°sharpen one side of that in the same shape as a nickel to about center flip the file over and do the same on the other side now you have a hard scraper that will scrape off the high spots. Of course the ideal tool would be a carbide scraper but the file will work the same just a lot cheaper. The carbide scraper you would be looking for would be used for scraping in precision machines and yes they make them in a power scraper also but they are quite pricey for the average person.
Muy útil me párese. Los motores de ahora con bloques de aluminio y materiales de tan mala calidad al recalentarse se deforman los bloques y normalmente toca bajar y desarmar para hacerlo rectificar y dar planitud. Me he ahorrado mucho Tiempo y dinero al cliente desde q me ofrecieron el servicio de rectificado con el bloque instalado. Simplemente se tapan los orificios de retorno aceite y lubricacion.
Materiales de mala calidad ? La verdad no sé en qué te basas en decir mala calidad , que valoras
good engine head resurfacing instrument # 👍🇵🇰
Thanks for liking
Get ready for the next rebuild with all that debris
Не отнимайте хлеб у фрезеровщиков😁
And we will just ignore all those metal shavings going into the oil passages
I’d be embarrassed to admit my engine was that small
Its this or 6 months wait in Q for machine shop to square deck block in CenTex
Your paint isn’t covering the part in the middle of the cylinders which means that the head gasket won’t sit nice and flat
Everyone worried about the shavings but not mentioning how out of plum the engine surface is. Id be more worried of the non-flat surface causing blow by before those little shavings I can blow with conpressed air.
You can definitely see the highs and lows. Go take it to a machine shop. So they can properly do it. Because I promise you the head gasket will leak.
Консольная жесткость этой руки бесконечна, похоже😂. Из таких людей бы гвозди делать.
Да ладно вам, все притрется и вся стружка выйдет с нагаром)
Good job👍
Thank you! Cheers!
Ну весь абразив в масляные каналы)))
That's not a head, That's the block
Nah I'll just haul it to a real machine shop thanks for offering but Uncle sam already Fs me every day.
At least take the engine out. What do you think will happen to piston rings even if they catch a little debris into the cylinders or oil and coolant passages
hello from France, not bad your tool! on the other hand wouldn't it be better to protect the pistons? because there they are not all going to like the filings at the first turn of the starter!
Oof, it looks like there may be a bit to go still depending on what your tolerances are
Head gasket is fixed but the engine is destroyed! Hint: prior to surfacing roll up strips of paper towel and stuff them into all passages to keep the metal & abrasives out of the engine internals. After surfacing is satisfactory remove all paper towel rolls from passages with a drywall screw while vacuuming then clean surfaces, apply copper coat. Perhaps using a larger surfacing block would also be beneficial. I've used a large file and had lasting results but I wouldn't recommend it.
Неправильная поверка поверхности
Доводка блока вручную - адский труд. Малейший перебор - иди сначала. Но. Здесь ошибки, порой, непростительны.
Видео о том что сдуло прокладку, а так же последующей капиталке!
Да Это не правильно никому не советую, но этот метод не плохо работает при должном подходе. И даже как то работает при подходе "на от@бись". Только трудозатрат обычно больше, чем снять и на плоскошлиф отвезти.
Someone tell me what’s the red paint he is applying and what does it do and what’s it for.
Этот двигатель ждал стружку в цпг и все каналы.
Такой ремонт возможен только на коленке в поле и то не именно так как показано на видео
So, it looks a bit like "Prussian blue", now comes in Red instead?
для таких случаев есть фрезерный станок
Keep going, brother
Кому абразивчика в мотор подкинуть? Работать будет как часики и тикать и цокать😅😂
Ofc between 2 and 3 would have a low spot...
В ручную идеально не получится.
Es dificil emparejar loideal sería en la rectificadora ❤❤❤ México
no way. you sand the center more than the ends
Даже с таким толстым слоем краски видно что прилегание не полное