Does it matter what direction rope is wrapped also? Just asking. Reminds me of a “stuffing box” on a boat where shaft goes through hull. It’s made from a waxy wool.
@@ntccXerblog If you wrap around the stem, how many loops can you have? Or, it is best to wrap half the threaded with 1.5 loops and the stem with 1.5 loop. Thanks in advance.
@Jirong Hu , Hi. Thank you for your comment. We think you should do what works best for you, given your supplies, skills, and situation. 😊 We chose a rope seal repair. If you do this, once the packing (or bonnet) nut is loose and its threads clean, you can wrap its threads with PVC tape in a single or double layer to prevent leaks there once the packing nut is tightened. Apply the PVC tape, wrapping in a clockwise direction and slightly stretching as you go; this will hold in place while you finish the repair with the rope seal. The rope seal goes on the valve stem and will be under the packing nut when that is tightened down again. The rope seal is also wrapped in a clockwise direction so that it stays wrapped as you tighten the packing nut back on the threads that you covered with PVC tape. Basically, the thin PVC tape prevents leaks between tight metal to metal surfaces (such as packing nut to threads), whereas the rope seal is used to seal larger gaps (such as the space between the valve stem and packing nut). Both tape and seal are applied in a clockwise direction so they tighten as the packing nut is tightened. Remember to tighten the packing nut just enough to stop the leak. Do not over-tighten it; that could cause restricted water flow. Please read and follow the cautions in this video's description. Whatever method you choose, we hope it works well for you. 💦✅
I have a same problem with main shutoff valve, local 5-star plumber quoted an estimate of $980 to replace valve and pressure regulator, I know they would be very unhappy to see this video, because now I can fix it with only a few bucks.
That's true, DIY john. And for anyone concerned with this type of repair, it is a good idea to wind the rope seal clockwise so the nut will tighten it, rather than causing it to unspool (if it catches the end of the rope). We were fortunate that the rope stayed put. Should it leak again in 30 or 40 years from now, we will endeavor to twist the rope seal in the clockwise direction. 😝 Thanks for commenting.
@@cjjonez if you mean that thin PVC tape, we would NOT recommend that. You want the rope seal shown in this video. It's not too expensive; and you don't need much. 😀 Thanks for the question. 👍 Hope this helps.
Here are links to two articles on How To Solder A Gate Valve. Both articles have useful info. Recommend reading both before tackling this job: homeguides.sfgate.com/solder-plumbing-valves-21379.html www.doityourself.com/stry/how-to-solder-a-gate-valve Good luck!
Will this work for a water shut off valve under the kitchen sink if the valve spinner is on top? Also do you have any videos or any advice how to stop a very slow tear drop leak coming from a steel pipe under the kitchen sink?
Under-sink valves are slightly different. They are compression valves. Just check online for how to articles or vids for them. Our experience has been that sometimes the service line (the flex line from the valve to the sink) needed to be replaced. Other times it was a simple matter of tightening the nut. And one time we had to add the PVC tape. Simple fix As for the tear drop leak, we would replace the small section of pipe that is leaking before the leak gets any worse. Be sure it is the pipe that is leaking, not a nearby fitting or valve. Water travels to the low spot, so a drip on a drain may run off the bottom of a pipe and look like a slow pipe leak. Just be sure you find the source before doing anything drastic.
Depends on where the hot water shut off valve is located. If the valve is the drain at the bottom of the water heater tank, then, yes, definitely need to drain the tank. You would also need to shut off the supply line coming into the top of the water heater tank or you'll be waiting forever for the tank to drain. :-P Read this video's description section for safety tips. If you don't feel comfortable with doing it, it may be better to hire a pro.
Tay, water flows downhill. So if your valve sits above the tank, you shouldn't need to drain the tank. You do still have to shut off the water supply coming into the valve. Also follow the safety tips, clike utting off nearby electricity and allow hot water to cool before working with the valve. Check the description for more info and good luck.
I would shut off the water heater first, if draining it. Otherwise it will be heating up without water in it and when you fill it back up, the heating elements will get fresh cold water coming in on the hot empty inside of water heater. Can cause steam and or cracks to happen inside.
I've been looking everywhere for this video thanks
You're welcome, ken harris. Hope it helps. Thanks for commenting.
Just want to say thanks for helping this very non-handy person fix something!
@larryellis6859
Glad this helped you. Thanks for your comment. 🙂
Aren't you supposed to wrap the packing rope around and against the stem? Between the stem and the packing nut.
bobby D, That's the general consensus. But our valve is fixed, no leak. Cheers!
Yeah the rope must be "Squished" between the shaft and the packing nut ;-)
Does it matter what direction rope is wrapped also? Just asking. Reminds me of a “stuffing box” on a boat where shaft goes through hull. It’s made from a waxy wool.
@@greggalexander8216 you want to wrap it in the same direction as you would be tightening the nut in
@@ntccXerblog If you wrap around the stem, how many loops can you have? Or, it is best to wrap half the threaded with 1.5 loops and the stem with 1.5 loop. Thanks in advance.
Would it be better to put the rope on clockwise so rope turns same direction as nut?
Yup.
I am having the same issue now. Home Depot tells me to replace the washer inside the valve, or replace the whole handle. What do you think?
@Jirong Hu ,
Hi. Thank you for your comment. We think you should do what works best for you, given your supplies, skills, and situation. 😊
We chose a rope seal repair. If you do this, once the packing (or bonnet) nut is loose and its threads clean, you can wrap its threads with PVC tape in a single or double layer to prevent leaks there once the packing nut is tightened. Apply the PVC tape, wrapping in a clockwise direction and slightly stretching as you go; this will hold in place while you finish the repair with the rope seal.
The rope seal goes on the valve stem and will be under the packing nut when that is tightened down again. The rope seal is also wrapped in a clockwise direction so that it stays wrapped as you tighten the packing nut back on the threads that you covered with PVC tape.
Basically, the thin PVC tape prevents leaks between tight metal to metal surfaces (such as packing nut to threads), whereas the rope seal is used to seal larger gaps (such as the space between the valve stem and packing nut). Both tape and seal are applied in a clockwise direction so they tighten as the packing nut is tightened.
Remember to tighten the packing nut just enough to stop the leak. Do not over-tighten it; that could cause restricted water flow.
Please read and follow the cautions in this video's description.
Whatever method you choose, we hope it works well for you. 💦✅
Thank you, sir....!
Most welcome!
Thank you so much for the video! You're a God sent! I was able to do it without a problem thanks to you.
Jamie B. You are so welcome! We just wanted to share what worked for us. Glad it helped you!
Wonderful...!
@robertohassenteufel1991
Glad you liked it. Thanks for commenting.
I have a same problem with main shutoff valve, local 5-star plumber quoted an estimate of $980 to replace valve and pressure regulator, I know they would be very unhappy to see this video, because now I can fix it with only a few bucks.
Thanks for the comment
Glad this helped you.
Plumbers are crooks
@johnnykurplutzo6789 - Some are.
Very helpful.. Thankyou for posting.. Happy holidays
You're welcome. Thanks for your comment.
Noticed the rope was put on counter clockwise
That's true, DIY john. And for anyone concerned with this type of repair, it is a good idea to wind the rope seal clockwise so the nut will tighten it, rather than causing it to unspool (if it catches the end of the rope). We were fortunate that the rope stayed put. Should it leak again in 30 or 40 years from now, we will endeavor to twist the rope seal in the clockwise direction. 😝 Thanks for commenting.
Thanks for the video very helpful
You're very welcome, fun times ahead. Glad we could help. Thanks for the feedback!
@@ntccXerblog do plumber tape work as well?
@@cjjonez if you mean that thin PVC tape, we would NOT recommend that. You want the rope seal shown in this video. It's not too expensive; and you don't need much. 😀 Thanks for the question. 👍 Hope this helps.
Can gate valves be. Soldered without disassembling?
Here are links to two articles on How To Solder A Gate Valve. Both articles have useful info. Recommend reading both before tackling this job:
homeguides.sfgate.com/solder-plumbing-valves-21379.html
www.doityourself.com/stry/how-to-solder-a-gate-valve
Good luck!
Life saver! Thanks.
You're welcome.
Will this work for a water shut off valve under the kitchen sink if the valve spinner is on top? Also do you have any videos or any advice how to stop a very slow tear drop leak coming from a steel pipe under the kitchen sink?
Under-sink valves are slightly different. They are compression valves. Just check online for how to articles or vids for them. Our experience has been that sometimes the service line (the flex line from the valve to the sink) needed to be replaced. Other times it was a simple matter of tightening the nut. And one time we had to add the PVC tape. Simple fix
As for the tear drop leak, we would replace the small section of pipe that is leaking before the leak gets any worse. Be sure it is the pipe that is leaking, not a nearby fitting or valve. Water travels to the low spot, so a drip on a drain may run off the bottom of a pipe and look like a slow pipe leak. Just be sure you find the source before doing anything drastic.
Life saver .. thanks!
Glad we could help. Thanks for the feedback. 👍
Strangely enough my leaky shut off valve does not appear to have a packing nut.
@EricRommens, you may need to replace the whole valve. Good luck. And thanks for commenting.
My leak is on hot water shut off do I have to drain the tank to fix knob
Depends on where the hot water shut off valve is located. If the valve is the drain at the bottom of the water heater tank, then, yes, definitely need to drain the tank. You would also need to shut off the supply line coming into the top of the water heater tank or you'll be waiting forever for the tank to drain. :-P Read this video's description section for safety tips. If you don't feel comfortable with doing it, it may be better to hire a pro.
@@ntccXerblog it's at the top hooked to water line that flows water into the pipes in the wall
Tay, water flows downhill. So if your valve sits above the tank, you shouldn't need to drain the tank. You do still have to shut off the water supply coming into the valve. Also follow the safety tips, clike utting off nearby electricity and allow hot water to cool before working with the valve. Check the description for more info and good luck.
I would shut off the water heater first, if draining it. Otherwise it will be heating up without water in it and when you fill it back up, the heating elements will get fresh cold water coming in on the hot empty inside of water heater. Can cause steam and or cracks to happen inside.
It's a water heater. Not a hot water heater
Yup. And in your kitchen you have a toaster. Go figure.
@@ntccXerblog lmaooo