SPI receivers DO NOT support D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) Modes (Packet Rates) and thus will not bind or sync with a TX module in any of these modes. This helped for me to bind Boxer, because default was F1000.
I've watched so many tutorials trying to set up my first ExpressLRS module and reciever, and this is by far the most straightforward and clear. Solved my issue too. Thank you.
Great video. How do i find the binding phrase on the tx12? I dont know what to enter into beta flight since i cant figure out what the binding phrase is on the tx
The binding phrase on your TX12 will need to be setup by yourself, suggest to check out my TX12 guide th-cam.com/play/PL8oE9qQrTLtcWcmj19GB0Zp7ahm3Dvv2P.html&si=eCtw_TEbZo6X_YwA
and if all this fails, try going to CLI, typing bind_rx, have the controller ready to bind, press enter on CLI first and then bind on the controller and Voila, but do everything he said first :)
Greetings, please help. I can not connect to the remote control. The remote control works, connected to 5 and 7 inch. In Betaflight, I entered the bind word, but it still doesn't work. I saved the settings, flashed it, it still doesn't connect.
hi i got a new radio recently so i was binding everything again and I had some problems with the mob 7, I bound my 5" quad with no problem but with my mob 7 when I plug it into betaflight I cant set up the modes the AUX selector is either blank or auto and the bars on the receiver tab are blank and don't show what channels are being used.
@@iFLYXWings6589 Connects just fine, but when I go to "flash firmware" it gives a "failed to open serial port" message. Beginning to think mines is just bad. Does it on multiple PCs.
@@iFLYXWings6589 so I just double-checked but so some reason in the log of BF it says "failed to open serial port". So it didn't flash the new 4.4 firmware.
Some dump reason maybe the USB cable, some even with the data mark will still not be recognized. Try a different cable to see if it works. Or try to force the FC into DFU mode to see if it works, press the button on the fc and plug in the cable at the same time should do the job.
Here’s the link for the factory default CLI dumps. Check to see if you find the one you need If not, e-mail me I’ll send you my presets www.happymodel.cn/index.php/2023/05/05/default-factory-dump-file-for-mobula8/
@@iFLYXWings6589 I have nothing in my back up what so ever only says default nosave. My first time doing this, my ELRS Boxer won't connect to my wi fi either. This is complete mess, I did go to edge tx and could not find the smt somthing to update the firmware.
When you press connect on beta flight further remote, I don’t see how it’s connecting. I have a Boxer ELLRS and it’s not connecting. I don’t get it. You just did it so fast. I don’t understand what you’re doing.
@@LoVeAmBiEnT Depends what binding method your using. Follow the method to set up your radio on elrs configurator with a binding phrase , then you can use Betaflight to set the binding phrase for the quad and then hit the bind button and your done . The quad will have a solid red LED and your radio should tell you telemetry lost and then regained if you did it correctly
Ok. I have a Pocket radio with 'PACKET RATE F1000 AND TX POWER 250 mH' trying to connect with MOBULA 8 and it doesn't work. What's wrong. Connecting with phrase. Radio version 3.4.3 Mobula version 4.5.1 (27-Jul-2024). This radio connects with a Pavo Pico.
I fly on CRSF daily, and find ERS so frustrating. Imagine: pure field, no wifi, no computer and friend left me a drone. How can can I bind it offline? Is it not a disaster?
I am new to the hobby and watched your videos about TX12 MKii and Mobula 7 binding videos, but I can't manage to get it connected through the method you showed in the videos. The video itself is super clear, but after I set the binding phrase through the wifi option in TX12, and Betaflight it just did not response. Any idea of where should I look for the issue?
@@iFLYXWings6589 Yes, it is updated to BF 4.4.2, the same as this video showed. I am using TX12 MK ii, and is 3.0.1 firmware, I just can't figure out why this is not binding. Do you have any clue of where should I be looking for?
@@xw2672 "D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) modes (package rates) are not supported by SPI receivers, and equipment in this mode will not be able to combine with an SPI receiver." This setting is in the elrs script on the transmitter (f1000 is installed on tx12 by default). Write if it helped.
flashie mi bassline, si va bien despues sigo con el mobula 8 que tiene la misma controladora de vuelo, solo que yo le puse walksnail hace unos minutos...por las dudas sigo con la 4.3.1 hasta comprobar que no falla el spi elrs 3.0.
I succesfully binded my mobula8 to my controller but when i disconnected the drone with the pc, my radio says telemetry lost and the controller doesnt seem to control the drone
All works fine for me in betaflight but then in reality drone motors dont move, so no arm, disarm, etc. Any idea? Binded mobula7 to jumper tpro v2 elrs thanks in advance
Boa tarde amigo meu drone bateu num galho e rodopiando caiu perdendo sinal com meu radio e nao vinculou mas o que pode ter ocorrido. Meu rádio é ocomando 8 ELRS
Mobular 8 amigo , até agora não consegui vincular com o rádio depois da queda eu ainda fiz um vôo mas quando coloquei no betaflith ele até deu sinal e depois foi diminuindo e não vinculou mas.
hey i just tries to follow this but my reciever settings arent saving? im also missing all of the elrs relation commands in the cli tab. please help haha
That is called channel mapping. This is how to fix it FPV drone Spinning in BF? Resetting channel maps might fix it th-cam.com/users/shorts8u-qkqUug18?feature=share
I was able to bind it but arm switch does not work under modes Aux 2 for acro/ horizon works fine Aux 3 for turtle works fine , but Aux 1 does not work , but if I change Chanel 5 which is my arm switch h to the opposite direction it works in beta flight. I believe there might be an issue with the board
hi i bought my mobula 8 drone and i also bought the betafpv literadio 3 elrs and i cant bind because i cant find the bind button on the drone i only see the boot button please help me
@@iFLYXWings6589 hi, is ok, I got it fixed, is choose the 250hz in the radio, maybe u can add notes in there, so that can helped more haha, mine using elrs 3, so maybe is the reason need chg the hz
I flashed mobula 8 to 4.4 and after arming, 1 or 2 motors do not spin. What is the problem ? How to check motors? I checked the connectors - its ok. Betafly has a reaction to the motors when the sliders move.
@@iFLYXWings6589 I solved the problem, but I'm not sure of the source yet. To test the drone, I used a 1s battery 660mah, which may not be enough for the initial spin-up of the motors. In the manual on the happymodel website I saw the ESC settings for the Bluejay configurator . There is a significantly higher min start power than the default ). After flashing new values and taken a fuller battery, the motors began to spin up as expected . Joining the FPV is not as easy as I imagined :)
I have a mobula7 1s elrs 2.4g drone and a radimaster tx12 MK2 ELRS. When I try to bind them, the image of the drone makes a coup, but does not connect. Bind phrase also does not work. Everything is updated to the max version. Any ideas how to fix it?
That doesn’t sound right, if you binding phrase is set up correctly both should have been bounded directly. Can you confirm you Mob 7 is BF 4.4 or above ?
iv been trying to get my Bassline to bind for over 4 months on and off, iv tried everything and still cant get the bloody thing to bind. Very frustrating. Iv updated the board to the newest betaflight, My transmitter is also on the same firmware, iv tried with and without binding phrases and still nothing. it just sits there blinking red and green. Grrrrrrrrrrrrr!
Which AIO board do you have? X12 or F405 ? Reason I’m asking, X12 is SPI F405 is serial. Also, have you plug it into betaflight to check the receiver tab? Any stick inputs ?
@@iFLYXWings6589 it's the Crazybeef4fSX1280. Which is obviously an spi based board and I have correctly selected this in the receiver tab, then ELRS. I have updated the board to the latest Betaflight firmware, and my ELrs transmitter is on version 3.2.1. If tried binding with a binding phrase and without. Used both 250hz and 500hz nothing. Also tried in hybrid mode instead of wide, nothing. Even took the quad apart to bind manually using the tiny bind button, guess what... nothing. All it does once plugged in or with a battery connected is blink red and green, Which to my knowledge is ready to bind. But nothing at all. I do believe i have a faulty board. If there's something iv missed them I'm all ears. Cheers
tuviste algun problema de rango en el spi elrs 3.0 o funciona bien? tengo miedo de salir de la version 4.3.1 de happymodel y que tenga algun problema... Gracias. Emiliano
Happymodel support told me officially that the version 4.4.2 will works on analog mobula 8 & analog bassline, always using the x12 FC. They dont recomend 4.5 yet
Bueno hoy probé el mobula 8 en el parque y con la versión 4.4.2 el spi pierde recepción a los 40 metros ....así que voy a volver la versión original perdiendo el osd HD...sino tendría que poner un elrs serial...pero x el momento no lo voy a hacer....
@@siniestrorave It is completely up to you~Btw if your Mob 8 is HD then you do not need to flash BF, you just need to flash your serial based ERLS receiver ERLS
@@iFLYXWings6589 My Mobula 8 came analog and I added a VTX walksnail. I wanted to update to 4.2.2 just to get the HD OSD, but the SPI ELRS range doesn't work properly and I lose the drone at 40 meters. I am going to stay on version 4.3.1 as there are no problems with the SPI ELRS 3.0 unless I add an external ELRS receiver later
1st try a few different cables- this is mostly the issue 2nd if cables is not the issue, run the impulseRC driver fixer to see if it fixes the issue impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe
@iFLYXWings6589 I can't see it. I can see the boot button but not bind button. I. Looking at the mobula 8 manual and the diagram of the FC does not show it, do u have any pic link of the FC
I've got it ready to fly now but my eachine goggles are not connecting to the drone, normally I conected them but just Turing power on and search for channels usually it finds the channel easily. This time I can't conect I tried two different eachine goggles, they work fine with my other drones. What do you think?
For Frsky, i am not so sure. but the general idea is to press the button on the FC or click bind at Betaflight and then hit bind on your Radio. Also double check to see if your protocol is at D8 or D16
i did the exactly same thing and it didnt work =/. I click on bind on betaflight, and when i click bind in lua script, the quad model on betaflight mades a flip and nothing hapens wtf kkkkk, maybe a problem on rx? There is anyway to check it?
Did you reloaded your presets? The binding method is based on using bind phrase which is the recommended method, try to set up your bind phrase for both your RX and TX
"D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) modes (package rates) are not supported by SPI receivers, and equipment in this mode will not be able to combine with an SPI receiver." This setting is in the elrs script on the transmitter. Write if it helped.
This video is incorrect, because a Mobula8 can come with a UART ELRS. You should specify that in the video otherwise people are gonna try flashing BF when they dont have to with a UART ELRS
@@puc19 This happens, what you need to do is 1. Remember which target your FC is 2. Press and hold the button on your FC and at the same time plug in the USB, this will force the FC into bootloader mode, if you do not see "Exit DFU mode" button glow up, try the process again
mine won't bind i tried everything. do i need to program the transmitter too? isn't the binding phrase written in the tx screen? i updated the firmwares i've seen a lot of videos but no one spends a word more on the binding process pls help🥲
Yes, you need to program the TX as well. 1. Make sure your TX is also at ELRS 3.X 2. Set up the binding phrase to be same as your TX 3. If you RX is SPI based set your packet rate to 500hz This video will show you how to flash the firmware of the TX How to Flash Radiomaster TX12 MK2 ELRS Firmware To ELRS 3.0 th-cam.com/video/5gUl62wKzgM/w-d-xo.html
Want to convert your Mobula 8 to a 4K Cinewhoop? Check this: th-cam.com/video/V7Qqe3dlAdM/w-d-xo.html
This is the 1st video I've seen where it actually tells me what I need to do
Glad to know the goal of this video succeeded
SPI receivers DO NOT support D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) Modes (Packet Rates) and thus will not bind or sync with a TX module in any of these modes. This helped for me to bind Boxer, because default was F1000.
This was what was stopping mine from binding - thanks! Hours of fiddling!
Wow! Thanks a lot! I spent 2 hours trying to bind my remote :/
Had to setup Packet Rate to 250Hz in lua erls script on my Radiomaster Pocket - bind successful
@@centralrif2058hello what else I should know in setting up the mobula7 for Pocket? I am still waiting mine in delivery.
@@ulungprabowo hi! there was just 1 thing - correct Packet Rate, mobula 7 2.4G ERLS works just great with radiomaster pocket erls
I've watched so many tutorials trying to set up my first ExpressLRS module and reciever, and this is by far the most straightforward and clear. Solved my issue too. Thank you.
Glad this helped !
Dude thanks for the video it's much appreciated just got the mobula 7 today and you have saved me heaps of hours lol it's appreciated
Glad this help~~ This is the reason why i am sticking with beginner tutorial contents
@iFLYXWings6589 just back from flying a few packs it's got great range and flight time looking love it thanks again
VERY helpful thank you straightforward to the point no BS worked the first time. subscribed
Glad it help! Thanks for the support
Thank you! I'm a complete newbie to this and your video helped me a lot.👍
Glad it help. Happy flying
Thanks for the info, haven't bought the whoop yet but will definitely come watch again when I do!
Thank you ! You will love this one ☝️
Short to the point everything u need nothing you don't great vid
Thanks !
Thank you!
You're welcome!
Great video. How do i find the binding phrase on the tx12? I dont know what to enter into beta flight since i cant figure out what the binding phrase is on the tx
The binding phrase on your TX12 will need to be setup by yourself, suggest to check out my TX12 guide
th-cam.com/play/PL8oE9qQrTLtcWcmj19GB0Zp7ahm3Dvv2P.html&si=eCtw_TEbZo6X_YwA
@@iFLYXWings6589 thanks bro I'll check it out. Keep up the good work
Excelent! Bought a Mobula8 with Frsky Rx option. Can I simply bind to my Zorro Tx?
If you Zorro TX is Frsky or 4in1 then yes
@@iFLYXWings6589 Thanx👍🤠🇿🇦
thanks!!!
Very informative and helpful video, do you have a guide how to bind Radiomaster pocket to Mobula7 or 8?thanks in advance for your response.
Thank you, sorry, have not received the pocket yet but the terminology should be the same. Will be doing a series of video to demo the setup
Thanks
and if all this fails, try going to CLI, typing bind_rx, have the controller ready to bind, press enter on CLI first and then bind on the controller and Voila, but do everything he said first :)
Greetings, please help. I can not connect to the remote control. The remote control works, connected to 5 and 7 inch.
In Betaflight, I entered the bind word, but it still doesn't work. I saved the settings, flashed it, it still doesn't connect.
Try setting your pkg rate to 500
Hi followed your instructions but I keep getting"No response from bootloader, programming: FAILED, when trying to flash ?
You can try to force the board to go into boot loader mode by pressing the FC button and plug in the USB cable, it should fix you problem
@@iFLYXWings6589 where is the boot button on the mobula 8 ?
hi i got a new radio recently so i was binding everything again and I had some problems with the mob 7, I bound my 5" quad with no problem but with my mob 7 when I plug it into betaflight I cant set up the modes the AUX selector is either blank or auto and the bars on the receiver tab are blank and don't show what channels are being used.
Any tips for “failed to open serial port” error?
Which part are you referring to? When connecting the drone to BetaFlight?
after flashing
What is the answer mine keeps saying that too
@@nickschlemmer3084 Same here. New PC with windows 11. Very frustrating
@@iFLYXWings6589 Connects just fine, but when I go to "flash firmware" it gives a "failed to open serial port" message. Beginning to think mines is just bad. Does it on multiple PCs.
So I still do not have the box for the binding phrase...Can you please help? I went through all the steps you showed
Please confirm you have flashed the bf version to 4.4 and select SPI ELRS at receiver tab and hit save
@@iFLYXWings6589 so I just double-checked but so some reason in the log of BF it says "failed to open serial port". So it didn't flash the new 4.4 firmware.
quand j'essaye de modifier le récepteur pour le mettre en Elrs ca me le remets toujours en série via Uart, je nais pas quoi faire.
everytime i try to flash the mobular 8 it says failed to open serial port. Does anyone know the solution to fix this?
Same issue
Some dump reason maybe the USB cable, some even with the data mark will still not be recognized. Try a different cable to see if it works.
Or try to force the FC into DFU mode to see if it works, press the button on the fc and plug in the cable at the same time should do the job.
Will this work for a mobula 6 elrs (not hd) too? I'm struggling to find a specific video for my new Mob 6. Thanks.
If your FC board is also the X12 then yes it will work
Tim, The Mobula that I bought from Banggood don't have any Data. How to get them?
Here’s the link for the factory default CLI dumps. Check to see if you find the one you need
If not, e-mail me I’ll send you my presets
www.happymodel.cn/index.php/2023/05/05/default-factory-dump-file-for-mobula8/
@@iFLYXWings6589 I have nothing in my back up what so ever only says default nosave.
My first time doing this, my ELRS Boxer won't connect to my wi fi either. This is complete mess, I did go to edge tx and could not find the smt somthing to update the firmware.
When you press connect on beta flight further remote, I don’t see how it’s connecting. I have a Boxer ELLRS and it’s not connecting. I don’t get it. You just did it so fast. I don’t understand what you’re doing.
@@LoVeAmBiEnT Depends what binding method your using.
Follow the method to set up your radio on elrs configurator with a binding phrase , then you can use Betaflight to set the binding phrase for the quad and then hit the bind button and your done .
The quad will have a solid red LED and your radio should tell you telemetry lost and then regained if you did it correctly
That was very helpful, thanks!
I’m glad it helps !
Ok. I have a Pocket radio with 'PACKET RATE F1000 AND TX POWER 250 mH' trying to connect with MOBULA 8 and it doesn't work. What's wrong. Connecting with phrase. Radio version 3.4.3 Mobula version 4.5.1 (27-Jul-2024). This radio connects with a Pavo Pico.
Change your pkg rate to 500, the mob 8 has an SPI based ELRS RX
@@iFLYXWings6589 Dude thank you very much😀
Have you got the factory board hex please, only the red leds are showing on fc now. I need to put it right back to stock.
Sorry, i don't currently have it, but you can try finding it on the happymodel website
핵심만 설명해 줘서 고마워요.
Glad it helped!
I had to send mine back, rx defected. Spi rx are not so good apparently
This is the problem with AIOs ….convenient but when something breaks …bye for the whole unit
I fly on CRSF daily, and find ERS so frustrating.
Imagine: pure field, no wifi, no computer and friend left me a drone. How can
can I bind it offline? Is it not a disaster?
Well ELRS does have a initial learning curve but once you understand it, it becomes quite easy
I am new to the hobby and watched your videos about TX12 MKii and Mobula 7 binding videos, but I can't manage to get it connected through the method you showed in the videos. The video itself is super clear, but after I set the binding phrase through the wifi option in TX12, and Betaflight it just did not response. Any idea of where should I look for the issue?
Please confirm your Mob 7 has been flashed to BF 4.4 or above ?
@@iFLYXWings6589 Yes, it is updated to BF 4.4.2, the same as this video showed. I am using TX12 MK ii, and is 3.0.1 firmware, I just can't figure out why this is not binding. Do you have any clue of where should I be looking for?
@@xw2672 "D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) modes (package rates) are not supported by SPI receivers, and equipment in this mode will not be able to combine with an SPI receiver."
This setting is in the elrs script on the transmitter (f1000 is installed on tx12 by default). Write if it helped.
I messed up on binding my Mobula8 can you tell me how to reset the Mobula 8 to factorl settings
Yes, you can go to the Happy model website to download the CLI files for the mob 8
flashie mi bassline, si va bien despues sigo con el mobula 8 que tiene la misma controladora de vuelo, solo que yo le puse walksnail hace unos minutos...por las dudas sigo con la 4.3.1 hasta comprobar que no falla el spi elrs 3.0.
Which FC are you using? X12 or Crazy F405? Depends on which one your ELRS flashing method my be different.
Hi.. my mobula8 hd is successfully bind with my controller but the stick in betaflight cannot move, am i missing something ?
1. Check model matching, turn on and off to see if that fixes the issue
2. Set your pkg rate to 500
@@iFLYXWings6589 thank you.. i will try
Bonjour jai commande un mobula 9 en spi frsky faut il achete un recepteur suplementaire ou est il directement integre merci
Sorry, don’t fully understand what you mean. If you have a Frsky receiver, you will need a Frsky radio or a 4in1 module
What if you don't have a binding phrase to ELRS? Can you hit bind receiver on beta flight and hit bind on your controller?
Yes, as long you have the same ELRS version
Thanks mate! I thouhgt something is wrong because elrs wouldn't create wifi...
Glad it helped ! Yes the mob 8 is using a SPI board
I succesfully binded my mobula8 to my controller but when i disconnected the drone with the pc, my radio says telemetry lost and the controller doesnt seem to control the drone
Ok.... just want to confirm, have you also plugged in a lipo?
yes i did@@iFLYXWings6589
Ma radio has the 3 bars signs for the connexion but the switches and stuff still wont work@@iFLYXWings6589
All works fine for me in betaflight but then in reality drone motors dont move, so no arm, disarm, etc. Any idea? Binded mobula7 to jumper tpro v2 elrs thanks in advance
It should not do that, so something is wrong. You can check the first tab of betaflight to see what are the arming flags
Boa tarde amigo meu drone bateu num galho e rodopiando caiu perdendo sinal com meu radio e nao vinculou mas o que pode ter ocorrido. Meu rádio é ocomando 8 ELRS
Sorry, need more details to help you.
First, please start with which drone do you have ?
Mobular 8 amigo , até agora não consegui vincular com o rádio depois da queda eu ainda fiz um vôo mas quando coloquei no betaflith ele até deu sinal e depois foi diminuindo e não vinculou mas.
@@voosempre.9946 Try reflating the betaflight firmware it should fix the issue
Vou tentar
hey i just tries to follow this but my reciever settings arent saving? im also missing all of the elrs relation commands in the cli tab. please help haha
Please provide more details, please confirm you have the analog version
idk why when i look in the reciever tab the drone is just spinning like crazy someone help
That is called channel mapping. This is how to fix it
FPV drone Spinning in BF? Resetting channel maps might fix it
th-cam.com/users/shorts8u-qkqUug18?feature=share
I was able to bind it but arm switch does not work under modes Aux 2 for acro/ horizon works fine Aux 3 for turtle works fine , but Aux 1 does not work , but if I change Chanel 5 which is my arm switch h to the opposite direction it works in beta flight. I believe there might be an issue with the board
Nope, your board should be fine, double check your settings
can, did you find it?! me too it not work. aux 1 2 3 4 xxx
Is there anyway to do this without a computer?
hi i bought my mobula 8 drone and i also bought the betafpv literadio 3 elrs and i cant bind because i cant find the bind button on the drone i only see the boot button please help me
The boot buttons is going to work as bind buttons
I bought Mobula8, when I try to select SPI Rx and save, it goes back to Serial all the time, what can be the issue?
Double check which model you have if its a HD(walksnail/AVATAR/DJI) then the AIO is F405. This board will have a serial based ELRS
@@iFLYXWings6589 actually I found instructions and its indeed works with serial connection
hi, i had follow all the step and i still got issue to connect my drone to my radio, i bind but noting happend, can i know here i wrong ?
Can you please advise what equipments are you using? I need to know the exact model of your drone and your radio to offer you a solution
@@iFLYXWings6589 hi, is ok, I got it fixed, is choose the 250hz in the radio, maybe u can add notes in there, so that can helped more haha, mine using elrs 3, so maybe is the reason need chg the hz
I flashed mobula 8 to 4.4 and after arming, 1 or 2 motors do not spin. What is the problem ? How to check motors? I checked the connectors - its ok. Betafly has a reaction to the motors when the sliders move.
Please confirm you have save and loaded your presets after flashing ?
@@iFLYXWings6589 I solved the problem, but I'm not sure of the source yet. To test the drone, I used a 1s battery 660mah, which may not be enough for the initial spin-up of the motors. In the manual on the happymodel website I saw the ESC settings for the Bluejay configurator . There is a significantly higher min start power than the default ). After flashing new values and taken a fuller battery, the motors began to spin up as expected . Joining the FPV is not as easy as I imagined :)
@@seriousserg4128 I see, glad that you resolved the issue!
I have a mobula7 1s elrs 2.4g drone and a radimaster tx12 MK2 ELRS. When I try to bind them, the image of the drone makes a coup, but does not connect. Bind phrase also does not work. Everything is updated to the max version. Any ideas how to fix it?
That doesn’t sound right, if you binding phrase is set up correctly both should have been bounded directly. Can you confirm you Mob 7 is BF 4.4 or above ?
iv been trying to get my Bassline to bind for over 4 months on and off, iv tried everything and still cant get the bloody thing to bind. Very frustrating. Iv updated the board to the newest betaflight, My transmitter is also on the same firmware, iv tried with and without binding phrases and still nothing. it just sits there blinking red and green. Grrrrrrrrrrrrr!
Which AIO board do you have? X12 or F405 ? Reason I’m asking, X12 is SPI F405 is serial. Also, have you plug it into betaflight to check the receiver tab? Any stick inputs ?
@@iFLYXWings6589 it's the Crazybeef4fSX1280. Which is obviously an spi based board and I have correctly selected this in the receiver tab, then ELRS. I have updated the board to the latest Betaflight firmware, and my ELrs transmitter is on version 3.2.1. If tried binding with a binding phrase and without. Used both 250hz and 500hz nothing. Also tried in hybrid mode instead of wide, nothing. Even took the quad apart to bind manually using the tiny bind button, guess what... nothing. All it does once plugged in or with a battery connected is blink red and green, Which to my knowledge is ready to bind. But nothing at all. I do believe i have a faulty board. If there's something iv missed them I'm all ears. Cheers
How can I update the receiver to ELRS 3.3.1? My transmitter also has ELRS 3.3.1.
Both have to be on the same level, right?
If you have a SPI ELRS receiver, this video should explained the steps, also as long you RX & TX are both in 3.X you are good
Ah OK Thank you@@iFLYXWings6589
After flashing the drone, the motors don't start, can you help?
Please confirm you have reloaded the presets after flashing.
Can the Mobula be bound to a Spektrum (Dx9) radio? Thanks
No, I will assume you need a Spektrum receiver
@@iFLYXWings6589 Thanks for your response.
tuviste algun problema de rango en el spi elrs 3.0 o funciona bien? tengo miedo de salir de la version 4.3.1 de happymodel y que tenga algun problema...
Gracias.
Emiliano
Nope, i dont recall having a range issue, but depends on how far you are looking. round the house no problem
Happymodel support told me officially that the version 4.4.2 will works on analog mobula 8 & analog bassline, always using the x12 FC. They dont recomend 4.5 yet
Bueno hoy probé el mobula 8 en el parque y con la versión 4.4.2 el spi pierde recepción a los 40 metros ....así que voy a volver la versión original perdiendo el osd HD...sino tendría que poner un elrs serial...pero x el momento no lo voy a hacer....
@@siniestrorave It is completely up to you~Btw if your Mob 8 is HD then you do not need to flash BF, you just need to flash your serial based ERLS receiver ERLS
@@iFLYXWings6589 My Mobula 8 came analog and I added a VTX walksnail. I wanted to update to 4.2.2 just to get the HD OSD, but the SPI ELRS range doesn't work properly and I lose the drone at 40 meters.
I am going to stay on version 4.3.1 as there are no problems with the SPI ELRS 3.0 unless I add an external ELRS receiver later
When i try to update it says failed to open port
1st try a few different cables- this is mostly the issue
2nd if cables is not the issue, run the impulseRC driver fixer to see if it fixes the issue
impulserc.blob.core.windows.net/utilities/ImpulseRC_Driver_Fixer.exe
When I save and reboot it does not save
I wonder where the binding button is on Mobula 8? I want to bing it manually. Anyone ?
It is on your FC the little yellow black dot
@iFLYXWings6589 I can't see it. I can see the boot button but not bind button. I. Looking at the mobula 8 manual and the diagram of the FC does not show it, do u have any pic link of the FC
@@albaniansuperiorshqipetari8055 the boot button will be your bind button as well. But still suggest you to bind it with a bind phrase
@iFLYXWings6589 I got it now I'm just going to bind it from configurator on receiver tab. Thanks for ur help Man
I've got it ready to fly now but my eachine goggles are not connecting to the drone, normally I conected them but just Turing power on and search for channels usually it finds the channel easily. This time I can't conect I tried two different eachine goggles, they work fine with my other drones. What do you think?
How do I do this with the frsky version? I'm trying to bind to my jumlert18
For Frsky, i am not so sure. but the general idea is to press the button on the FC or click bind at Betaflight and then hit bind on your Radio. Also double check to see if your protocol is at D8 or D16
@@iFLYXWings6589 I got it.... switched from d16 to d8 and bound right away
@@lancekinshella5817 Glad you got it fixed
Hi i bought two mobula 8 tbs version.. does elrs perform better than tbs?
They are quite similar in performance but TBS is generally more costly but beginner friendly, ELRS has the initial learning curve you need to overcome
i did the exactly same thing and it didnt work =/. I click on bind on betaflight, and when i click bind in lua script, the quad model on betaflight mades a flip and nothing hapens wtf kkkkk, maybe a problem on rx? There is anyway to check it?
Did you reloaded your presets? The binding method is based on using bind phrase which is the recommended method, try to set up your bind phrase for both your RX and TX
"D(D250, D500), F(F500, F1000) and Full Res(100Hz Full Res, 333Hz Full Res) modes (package rates) are not supported by SPI receivers, and equipment in this mode will not be able to combine with an SPI receiver."
This setting is in the elrs script on the transmitter. Write if it helped.
do you fix that?
Hello would it be possible to flash the new hummingbird v3 to 2.5 in order to bind to my elrs zorro on 2.5?
Good question, by theory, yes, but I don’t own or have owned a newbeedrone quad before. If I remembered correct NBD has self developed software ?
binding phrase box doesnt pop up
You need to save and restart
You can ask for a file ?
Can i connect a tx12 with a avata?
Nope not possible
How about a pavo20
This video is incorrect, because a Mobula8 can come with a UART ELRS. You should specify that in the video otherwise people are gonna try flashing BF when they dont have to with a UART ELRS
I agree , this video was made prior of the HD version that came out with a different AIO. Let me update it to analog only
Every dawn video just has the person clicking connect. NONE of my drones connect to betaflight
@@just_bright in that case check you cables, this is the most common issue
Does this work with mobula 6
the concept is the same, just the mob 6 has a different FC thus your target will be different
ok
@@iFLYXWings6589
For so,e reason it is stuck on “Initialising reboot to boot loader
@@puc19 This happens, what you need to do is
1. Remember which target your FC is
2. Press and hold the button on your FC and at the same time plug in the USB, this will force the FC into bootloader mode, if you do not see "Exit DFU mode" button glow up, try the process again
Ok
thank you very much for this bro it really help🤙🚀✈
Glad it helped !
could you send me the backup file please
Can you please email me at piggycraftsman@gmail.com? I will send over the file
is this everything I need to do to bind my radio and drone? i'm having some trouble getting them to bind
In most of the cases, this will be all you need to do.
Its just not workin now! Regrettin buyin this mob8
Sorry to hear this any particular issues?
Спасибо👍🤝
mine won't bind i tried everything.
do i need to program the transmitter too? isn't the binding phrase written in the tx screen? i updated the firmwares i've seen a lot of videos but no one spends a word more on the binding process
pls help🥲
Yes, you need to program the TX as well.
1. Make sure your TX is also at ELRS 3.X
2. Set up the binding phrase to be same as your TX
3. If you RX is SPI based set your packet rate to 500hz
This video will show you how to flash the firmware of the TX
How to Flash Radiomaster TX12 MK2 ELRS Firmware To ELRS 3.0
th-cam.com/video/5gUl62wKzgM/w-d-xo.html