How to make Saloon Doors for the steps
ฝัง
- เผยแพร่เมื่อ 8 ม.ค. 2019
- In this video I am building Saloon style doors the separate my staircase. The doors are 16” wide “each” by 36” tall and 3/4” thick. They are made out of project panel lumber with trim pieces. Total cost for this project is around $60
- แนวปฏิบัติและการใช้ชีวิต
Great video. Poor puppy got blamed. However I learned the steps to DIY a swing door. Thanks
You did a great job and your doggy at the end was talking his mess 😂. Thank you
Oh thank you for this! I'm going to get hubby to make full length ones for our game room entrances. I can't believe you made it so cheap! They want an arm and a leg for them in stores. Beautiful job!
Very good video!
Nice job man
Great job on this video. Loved that you stuck to the point, didn't repeat too much and showed us how to overcome challenges. Best one I have seen thus far for making these and I am going to use this to make my own. Thanks so much for giving us your time to produce this!
This is a way better idea than using a baby gate! Love it!
Oh I love them!!! I feel like I can do this! Thank you so much for the great video!
Great job you made it look easy. You must have been through a few saloon doors in you day ha!
Thank you I’ll give it a try
Great Idea ! And a Great job !
You do very good job sir I learned from you now
I'm pretty good at what I do but I can say this would be the first job that didn't know how to hang the double swinging hinges but looking at the video job well done really appreciate it thank you my name is Jack
Good and understanding way you teach how to make swing door
looks amazing, well done!
Looks good. I wanna build the police caddy u made for my stuff but haven’t tried it yet lol
lol 😂 damn you made me laugh so much when you said all because of him ..nice work tho brother 🙏🙏
Looks like you were blessed with a new miter saw. Awesome video keep up the great work brother.
neil lisa I was, and it’s nice to have one that actually cuts square haha!
I know what you mean still working my way towards one lol. Still praying for your family brother.
Beautiful work sir .
Windy Miller thank you!
Like the color! What stain is that?
Hey Popo, I was hoping you could answer a question for me, I’m trying to put some doors on a little pool pump shed I built and I made some doors out of 1x4s and I’m not sure they are thick enough for my 3 inch hinge. The screws don’t seem to have much to hold on to. Should I add something to make it thicker or redo the doors and use a 2x2 on the frame instead? For some reason I can’t understand that part of the hinge. I can’t figure that part out! Any help you can give me would be appreciated. Thank you!
I like how you solved the thickness problem.
Thank you indeed as win Hong that I can keep open at times
How much space do I need for hinges and center ,?
Hey my friend, great video. Can you answer a question about the hinges? I've got saloon doors already hung and up, and somehow, the pins have popped out of one door. That door doesn't swing back into place and I can't figure out how to re-establish the tension on the hinge to set the pin in the hole. Can it be done without taking the door off the hinge?
Bruce Kellison Yes you can adjust them while they are mounted. I used a center punch, or you can use a small screw driver. Place it in the holes where the pin goes. Use the screw driver or center punch to twist the hinge where the pin goes in until you get the desired tension. You may have to play with it until you get it right, but my hinges adjust on the top and bottom. You will know your going the right way because it will feel tighter. So in other words using the center punch, place in one of the pin holes, twist the hinge, then while holding it in place slide the pin in a free hole until it’s the way you want it. I hope this makes sense and helps you out!
Bruce Kellison Also, the pin slots on top will adjust one direction of the door swing and the bottom will adjust the swing in the opposite direction.
I LEARNED A LOT
I like the Saloon doors that you made! I did not understand what the hinge is called Sir, could you kindly tell me the name of the type of hinges you used for your nice set of doors? Thank you for sharing this project with us all!👍
Double acting spring hinges
MAE HAY per Lowe’s website they have 2 names. “Barrel Hinge” and “pivot door hinge”.
Popo's Woodworks Thank you for your quick response to my question sir!
I want to do this but on a double screen door-think it’d work?? 🤔
I tried a different saloon door hinge that doesn't have the self closing spring. Do your hinges swing open and closed in both directions? I couldn't tell from the video and can't quite see how your hinges would work that way. Thanks for sharing 🙂
They do swing both ways. I can’t remember the brand but I got them from Lowe’s
@@PoposWoodworks thanks for replying. The reason I asked is because they look like standard self closing door hinges. If you ever remember the brand I would appreciate the info, but at least I know they're out there. Thanks again for sharing and replying 🙂
I’m building doors so my dogs do whatever they want and I don’t have to get up to let them out the backyard
I am thinking of putting a 'hidden door' in my house, so a door that looks like a book case but secretly is a door.... Is that something you could make a video about?
This is exactly what I need to keep the toddlers out of the kitchen.
Woodglut has a very large project base.
U got it buddy 👍
Mine works too. I used the Woodglut plans and performed it without any problems.