Thanks for the reply to my eg k swap issue s. I will check out the main relay start up sequence like you mentioned. It has been some time since I sent that question over to you . What I ended up doing with the main relay was re grounding it . And the ecu and fuel pump turned on with the key. I believe my reissue with the auto crv engine harness . I attempted to convert to manual. I had messed up some grounds in the harness and purchased a manual 04 crv harness and converted it for the 04 accord motor and have been driving the car for probably 5-6 months now .
This swap was a big learning curve. I also had issues with the speedometer not reading . With the counter shaft speed sensor. I changed the wiring on the engine harness and plug . From what I’ve seen on your videos that should of pegged the speedo when moving slowly. I had nothing. I bought a converter box and the the speedo in the dash worked but no speed reading on the ecu . I latter found out that ha motor sport sold me a crv auto ecu with a k pro installed. So I had to run a jumper wire from the k pro board to the vss out put and everything works .
Forget k swap mounts for 4cyl 98-02 accord. Any plans for j series mount? The v6 subframe and k member bolt up. But, the bracing for passenger side mount has to be drilled and cut out of a donor v6 chassis.
Need advice on what engine to swap into my 1985 Honda Civic Wagon. It’s automatic and also want to swap to M/T. What are your suggestions? Thank you VTec Academy
@mightyboochX I doubt it, there's probably only one that's on the internet, I'm doing that swap now it's difficult but most of the issues are with the front end matching up due to the engine being turned around but maybe back in 2005 it was impossible but not anymore
On my Australian delivered rb1 odyssey I used an 05 accord euro loom and ecu for my manual swap with a couple of mods. Only cruise control is lost everything else works. I'm on " honda odyssey Australia " if you have any questions
i really wish you guys would have done a 6th gen accord k swap mount kit years ago,.. i miss my 6gen accord coupe i had about 10 years ago and always wanted to do a k swap into it ,,,.but now they are very hard to find around my area,...
Did you confirm if the K24 w/ RDX head will fit in the 02-06 CR-V? I remember it wouldn't clear in the RSX. Are the steering racks in the same exact location between RSX and CR-V?
I have a 96 integra with a b20b. I got it running one day and it stopped running the same day but I don’t know why. I’m getting fuel, spark, air, has a new distributor cap, spark plug wires, spark plugs, and a new battery. Any help would be greatly appreciated
Hopefully you can help out. I'm currently in the process of doing a 04 tsx auto to manual swap. I got everything on, I just need some info on the ecu part, I have a 04 manual ecu available but is it just plug and play after I get it reprogrammed to my car? Or are the pin outs different? Hope to hear from you vtec academy.
I need a k swap to 6th gen video no one has ever done it ,the 6th gen coupe is my fav Accord and no one gives it the love it deserves.and FYI the 6th gen is 98 to 02 ....people always saying the wrong years lol
@@VTECAcademy I have a beautiful 02 seventy-three thousand Miles five-speed note right after I commented yesterday this a lady totaled it in the parking lot .... Completely smashed in the back side panel and the whole car is crooked now. She tried to take off and leave the scene she left her about 4 hours until the sheriff was looking for her....
That's facts brotha, facts. 98 black EX sedan here. 2.3L VTEC 5 speed. 6th gens are really underrated and that's fine with me but jesus nobody even knows sht about them and it's pretty ignorant honestly.
@@shoDOHC I'm still in the process of looking for one. Mine got totaled right after I made this comment. 02 Ex 73000 miles. I had it for 10 years I bought it with 21,000 mi from the original owner. It was my baby.
Hey. Question. Is there a mount kit for a J or k-series in a late 90's Honda odyssey. I know they are similar to the Accord as far as mounting positions (right?). Friend needs a new engine and wants something with a little more power at a cheaper price.
Wait did he say he is redesigning the mounts for the CB Accord? When is that going to happen? Also is that the reason the axels have been sold out for awhile for the CB?
@@VTECAcademy what is going on with the axles unavailability ? Sorry if this is a noob question but are the axles completely necessary or only for boosted applications? I’m an under the impression that the H22 is a more common swap because the axles work and the k swap requires new axels. Thanks for any clarity on this.
What do you guys think about most of the k swap thermostat swivel housings not using the bypass valve off an oem thermostat. Would it cause overheating from the radiator not flowing properly because the bypass is left open?
Long time accord owner and current 6th gen Euro R owner. The 6th gen accord find itself in very tough spot where K swapping is concerned because of its subframe design. The 6th gen uses a combination of the previous generation caster rod with a two piece subframe that hugs the H/F series really tight. To kswap this gen accord would sadly involve a heavily modified subframe from what Ive looked at. There may be some work arounds out there which im sure Brian would explore looking into this platform. hoping to hear more on this in the future. There are tons on SiR and Euro Rs here waiting for a K24 + 6mt
You would need to use the CDK mount kit and an aftermarket front crossmember (where radius rods go). The k series engine is designed to sit a bit closer to the rad support so the axles don’t bind.
@@401kid6 Still wouldnt work with the CDK kit even if you eliminated the radius rods. the 6th gen subframe would interfere with the kseries oilpan and transmission
If you need a chassis for the k swap mounts for the 98-02 accord, you could come grab my roller chassis. It’s completely gutted (building an f20b for it) so it’s gonna be awhile lol
@@VTECAcademy Well that’s the tough part, Minnesota, she’s just a bare bones shell that will make some power one day. But I mean there’s nothing in the bay, she’s in primer stage
I need advice on ecu setup for my 2000 accord coupe original 3.0 v6 auto to manual swap. Absolutely love the body style and i have the manual trans, shifter cables, pedals, and clutch reservoir. Waiting to buy all the odds and ends till I figure out the ecu. I want it to be oem and tuneable. I understand I maybe need a jumper harness but for the most part I want the car to be turn key and it be all Honda stuff, yanno for the most part. Can’t seem to find a direct solution so far.
K swapped 6th gen would be a dream. 6th gens are my favorite gen next to the 10th gen. I’d love to k swap one of those as I plan on k swapping my ge8 fit. Be nice to have 4 K cars (2 10th gen accords, fit, and 6th gen accord)
I like the idea of a motor swap . Then I watch your videos and think who is capable of this, not so straight forward, task. It seems like a better idea to just buy the car with that engine in it. The Civic in the back ground is really distracting.
We need the 6th gen Accord K swap kit! I'd buy one so
fast.
Me too.
Lemme know when you mess with the 98-02 accord k mounts bro. I'll be glad to do some testing on my channel
When we get to them some time down the line it'll be on here for sure. Those Accords are relatively light for their size. Thanks for watching!
I'll be watching that for sure big homie!!
Let me know when they come out 👍
We've been waiting a LONG time for a K mount kit on the CG chassis. Wonder why it hasn't happened yet 🤷🏿♂️
@@VTECAcademy Any updates on this? I would love to see a Kswap for the CG, I'd even donate a CG to you guys just to see.
Yes finally my moms accord engine went ive been wanting to swap but I don’t wanna go with an H
Thanks for the reply to my eg k swap issue s. I will check out the main relay start up sequence like you mentioned. It has been some time since I sent that question over to you . What I ended up doing with the main relay was re grounding it . And the ecu and fuel pump turned on with the key. I believe my reissue with the auto crv engine harness . I attempted to convert to manual. I had messed up some grounds in the harness and purchased a manual 04 crv harness and converted it for the 04 accord motor and have been driving the car for probably 5-6 months now .
This swap was a big learning curve. I also had issues with the speedometer not reading . With the counter shaft speed sensor. I changed the wiring on the engine harness and plug . From what I’ve seen on your videos that should of pegged the speedo when moving slowly. I had nothing. I bought a converter box and the the speedo in the dash worked but no speed reading on the ecu . I latter found out that ha motor sport sold me a crv auto ecu with a k pro installed. So I had to run a jumper wire from the k pro board to the vss out put and everything works .
Glad you saw the video! Some swaps are a battle, no matter how many times you do them.
E1 : usdm fuel pump trigger, E10 : jdm Fuel pump trigger. The pins you mentioned are A1 for knock sensor.
Forget k swap mounts for 4cyl 98-02 accord. Any plans for j series mount? The v6 subframe and k member bolt up. But, the bracing for passenger side mount has to be drilled and cut out of a donor v6 chassis.
depending ok what ecu is used if its jdm ecu needs to jump e160 on back side of ecu with a 0 ohm smt resistor to let ecu work in usdm wiring config
This is the video I’ve been waiting for ! My favorite car I owned was a 2002 accord sedan.
I love hasport customer service
They try! Glad to see the hard work is appreciated.
Any update on the CG K swap kit??
Great info share, Thank you Brian!
You bet! Sometimes the information on another person's issue can set off an idea on another thing.
Id definitely let you use my 00 accord for testing
Any update on the 1998-2002 cg6 accord kswap mounts?
K24W help !! Would like to see what you can do with it or swap
Any developments in the near future with the k20c4 swap and the 10 speed auto?
Not yet.
Need advice on what engine to swap into my 1985 Honda Civic Wagon. It’s automatic and also want to swap to M/T. What are your suggestions? Thank you VTec Academy
A K series would serve you well!
th-cam.com/play/PL9Qq92QbHKkhb_xhQNh1v8WhiT__0jb0M.html
I have a rsx type s complete swap . My only problem is what I want to put it in.
Can you put a 50 degree VTC on a k24 Honda that only has 25 and keep the stock ECU and and run fine
95 accord here I want the auto swap k24
Great work and love the details 👌
Ef looking simply clean
Sick video. So informative
What motor mounts should i use if i where to swap a k24 into a 2001 accord lx coupe?
Good luck with that
Could probably use the mounts that went with the k24 and some modifications and welding to fit them
@@iPlAyInSuRgeNcY theres only 1 running k swapped 6th gen
@mightyboochX I doubt it, there's probably only one that's on the internet, I'm doing that swap now it's difficult but most of the issues are with the front end matching up due to the engine being turned around but maybe back in 2005 it was impossible but not anymore
@mightyboochX if you can swap a 97 with a k24 then you can definitely swap in into an 01
The question about the car starting and shutting off. He said stock ECU. Immobilizer? 97 civic k24
Man would love k for my 02 accord
On my Australian delivered rb1 odyssey I used an 05 accord euro loom and ecu for my manual swap with a couple of mods. Only cruise control is lost everything else works. I'm on " honda odyssey Australia " if you have any questions
Nice! Thanks.
Continue 👍
Thank you!
Do you know if the axles from the k series work in the 98 02 accord? I think a j2k would be a easy j series manual swap
I haven't tried that.
Is there a manual transmission for a 2000-2002 accord V6???
i really wish you guys would have done a 6th gen accord k swap mount kit years ago,.. i miss my 6gen accord coupe i had about 10 years ago and always wanted to do a k swap into it ,,,.but now they are very hard to find around my area,...
Just a fan wanting to say hi✌✌
Hey hey!!
*Patiently waiting for CDK mount revision* 🙂
I just finished the BB1 Prelude. CD and CB next.
Did you confirm if the K24 w/ RDX head will fit in the 02-06 CR-V? I remember it wouldn't clear in the RSX. Are the steering racks in the same exact location between RSX and CR-V?
I Dont think it will.
Hey I’m k24a swapping an 06 accord and wanted to know how your ktuner ecu went
The car has been running on a base tune for TSX with the KTuner, since we did the swap.
Where are you located? I have a 99 accord coupe and would love to use my vehicle as a test dummy.
Phoenix, but I would rather buy one. I may need it for other things.
I have a 96 integra with a b20b. I got it running one day and it stopped running the same day but I don’t know why. I’m getting fuel, spark, air, has a new distributor cap, spark plug wires, spark plugs, and a new battery. Any help would be greatly appreciated
Could be your ignition.
If you're getting fuel and spark,. check to see is the timing belt slipped.
Hopefully you can help out. I'm currently in the process of doing a 04 tsx auto to manual swap. I got everything on, I just need some info on the ecu part, I have a 04 manual ecu available but is it just plug and play after I get it reprogrammed to my car? Or are the pin outs different?
Hope to hear from you vtec academy.
Plug and play on the ECU. There are wires to run and wires to remove though.
Is there a link you might have to go off of?
I need a k swap to 6th gen video no one has ever done it ,the 6th gen coupe is my fav Accord and no one gives it the love it deserves.and FYI the 6th gen is 98 to 02 ....people always saying the wrong years lol
I am looking for one.
@@VTECAcademy I have a beautiful 02 seventy-three thousand Miles five-speed note right after I commented yesterday this a lady totaled it in the parking lot .... Completely smashed in the back side panel and the whole car is crooked now. She tried to take off and leave the scene she left her about 4 hours until the sheriff was looking for her....
That's facts brotha, facts. 98 black EX sedan here. 2.3L VTEC 5 speed. 6th gens are really underrated and that's fine with me but jesus nobody even knows sht about them and it's pretty ignorant honestly.
@@shoDOHC I'm still in the process of looking for one. Mine got totaled right after I made this comment. 02 Ex 73000 miles. I had it for 10 years I bought it with 21,000 mi from the original owner. It was my baby.
@@tylanbakardi2750 damn dude that is awful. Hope you find another soon
Hey. Question. Is there a mount kit for a J or k-series in a late 90's Honda odyssey. I know they are similar to the Accord as far as mounting positions (right?). Friend needs a new engine and wants something with a little more power at a cheaper price.
When the new CDK mount kit is done you will be able to use that one.
Wait did he say he is redesigning the mounts for the CB Accord? When is that going to happen? Also is that the reason the axels have been sold out for awhile for the CB?
I just finished the BB1 mounts. CB and CD next.
@@VTECAcademy what is going on with the axles unavailability ? Sorry if this is a noob question but are the axles completely necessary or only for boosted applications? I’m an under the impression that the H22 is a more common swap because the axles work and the k swap requires new axels. Thanks for any clarity on this.
What do you guys think about most of the k swap thermostat swivel housings not using the bypass valve off an oem thermostat. Would it cause overheating from the radiator not flowing properly because the bypass is left open?
Interesting question. We have not heard of any issues from this.
I run hybrid racing swivel thermostat housing. It’s swivel but still uses oem thermostat
Any possible way I can install k pro ecu in a tsx chassis doing a throttle by cable conversion ???
Just use flashpro
You can. It just takes some wiring adjustments.
Could you k - swap a Hyundai Accent 1.6L 4Cyl with a k20 or k24 like you can a Honda fit? Thank you
I am pretty sure you could.
Is it taco Tuesday? 🤣
This was pretty awesome for info!
Has No one (apart from that Russian fellow some years back..) ever put a K in the CL1 Accord Euro R?
Update?
6th Gen Accord is from 1998-2002.
I want a 98-02 accord with crv driver train, awd. How?! 😅
First I need to find one of those chassis and next I need to make the mount kit.
@@VTECAcademy also, I think the V6 has a different engine bay configuration than the 4 cylinder. Just to add another variable.
if u still need a 6th gen accord u can borrow mine for as long as u need
💯👍
Hey I have a chassis for 98-01 accord if your still looking for a chassis
Where are you located?
Long time accord owner and current 6th gen Euro R owner. The 6th gen accord find itself in very tough spot where K swapping is concerned because of its subframe design. The 6th gen uses a combination of the previous generation caster rod with a two piece subframe that hugs the H/F series really tight. To kswap this gen accord would sadly involve a heavily modified subframe from what Ive looked at. There may be some work arounds out there which im sure Brian would explore looking into this platform. hoping to hear more on this in the future. There are tons on SiR and Euro Rs here waiting for a K24 + 6mt
You would need to use the CDK mount kit and an aftermarket front crossmember (where radius rods go). The k series engine is designed to sit a bit closer to the rad support so the axles don’t bind.
@@401kid6 Still wouldnt work with the CDK kit even if you eliminated the radius rods. the 6th gen subframe would interfere with the kseries oilpan and transmission
Out of the box k mounts would be a godsend for 6th gen accords
If you need a chassis for the k swap mounts for the 98-02 accord, you could come grab my roller chassis. It’s completely gutted (building an f20b for it) so it’s gonna be awhile lol
Where is it?
@@VTECAcademy Well that’s the tough part, Minnesota, she’s just a bare bones shell that will make some power one day. But I mean there’s nothing in the bay, she’s in primer stage
Hey is there any K mount kit for 88-91 honda prelude? Proud 3rd gen Prelude owner 😎.. currently with an hswap [BA ALLIANCE PLEASE]
That hood line is so low. At some point I’ll try one in.
I need advice on ecu setup for my 2000 accord coupe original 3.0 v6 auto to manual swap. Absolutely love the body style and i have the manual trans, shifter cables, pedals, and clutch reservoir. Waiting to buy all the odds and ends till I figure out the ecu. I want it to be oem and tuneable. I understand I maybe need a jumper harness but for the most part I want the car to be turn key and it be all Honda stuff, yanno for the most part. Can’t seem to find a direct solution so far.
The Hondata J swap ECU.
…………..J-SERIES 🫡
K swapped 6th gen would be a dream. 6th gens are my favorite gen next to the 10th gen. I’d love to k swap one of those as I plan on k swapping my ge8 fit. Be nice to have 4 K cars (2 10th gen accords, fit, and 6th gen accord)
Why not just j swap the 6th gen accord ?
I like the idea of a motor swap . Then I watch your videos and think who is capable of this, not so straight forward, task. It seems like a better idea to just buy the car with that engine in it. The Civic in the back ground is really distracting.
You can use my 98
Maybe one day!
Needs a G23.
Yikes... 6th gen accords. Poor things. Just get a CB7!
😂 Haaaarsh!
I love my 99 EX Sedan! 275k with manual transmission and going strong!