I've seen the same design of table saw in a few other channels. It's nice and I must say this is the best looking among them. But how can you tilt the saw?
buenas noches señor muy buena su aportacion sobre la fabricacion de esta sierra de mesa es para las personas que nos gusta la carpinteria pero no tenemos la manera de como adquirir una herramienta a veces costosas gracias por su tiempo y amabilidad de compartir sus conocimientos, felicitaciones, DIOS lo bendiga, saludos desde huatabampo, sonora, mexico
Badass! Only need to add a tab behind the blade so you don't run the risk of kick backs due to the possibility of tension in the wood and closing onto the blade sending the wood into your face or nuts!
Cordial saludo y felicitaciones por este proyecto tan precizo y funcional. Desearía saber más de de la potencia motor, dimensiones etc, las especificaciones técnicas del proyecto pero en inglés o español de ser posible. Desde Colombia un abrazo y me suscribo con like.
Exelente trabajo amigo saludos desde huánuco Perú...por favor podría enviarme los planos en PDF ó programa SketchUp gracias y muchas bendiciones para usted
-Parts Used- Bearing shaft Single-phase , 220-240V , 60Hz , 3600RPM 1.5Kw(2HP) Bearing shaft bearing Square pipe Aluminum profile 4080x 800mm Thank you for your interest in my video
Parts Used Bearing shaft Single-phase , 220-240V , 60Hz , 3600RPM 1.5Kw(2HP) Bearing shaft bearing Square pipe Aluminum profile 4080x 800mm Thank you for your interest in my video
Прекрасная работа, но циркулярная пила без наклона диска имеет урезанный функционал. Если уж делать настолько качественно то и над механизмом наклона следовало поработать! А так отличная настольная пила!👍
Thankyou me urge aser mis propias herramientas .perdi mi empleo y necesario construir juego de sala, gracias a ustedes los youtubers como tu ,aprendemos mucho,mis hijos adolesentes y yo construimos mueble de concreto chorreando para fregadero de cocina, así que también podremos aprender con trigo gracias
Buenas, de Perú, FELICITACIONES buen trabajo de la Mesa circular, sería excelente considerar las medidas de dicha máquina y la sugerencia del motor de cuantos HP se utilizaría para un excelente trabajo. GRACIAS.
Hello my friend.. I love this table saw u built bro. I have a couple of questions of u don't mind me asking u..?? Q. What are those bigger bearing holders called u used for the Blade lift.. U used 2 of them but I cannot for the life of me find any of them online. Could u drop a link for them on here if u have a minute? I'm about to embark on a Table saw build of my own and I'm in 2 minds about what to use for the top/Table.. I like how u used the Aluminium but what width was that u used for the top of the table?? It looks awesome dude. If I'm not mistaken u also use those Spiral tap bits too?? Are they better than the original type ones? Anyways I wanna say how great ur table saw build is and thank u for inspiring me to get going with mine soon.
hello I replied but it got deleted so I'll reply again I translated the words you inquired into a translator and read them. It's not an accurate translation, so I'll try to answer with a sense ^0^ Gcr 15 UCF203 ko.aliexpress.com/item/1005003777979794.html?spm=a2g0o.productlist.main.1.7d182ea1RlCJlg&algo_pvid=ad5c793f-9a79-46e2-b393-e82f6ea0ff98&algo_exp_id=ad5c793f-9a79-46e2-b393-e82f6ea0ff98-0&pdp_npi=3%40dis%21KRW%219195.0%217535.0%21%21%21%21%21%402145277316858830540082603d07b5%2112000027133823735%21sea%21KR%21888194637&curPageLogUid=BdJmtjokdJlo The top/table size is 800x700mm. The stainless plate on the birch plywood is 1T When using an aluminum plate, it is recommended to use a product with a thickness of 2T or more. thanks for watching the video
-Parts Used- Bearing shaft Single-phase , 220-240V , 60Hz , 3600RPM 1.5Kw(2HP) Bearing shaft bearing Square pipe Aluminum profile 4080x 800mm Thank you for your interest in my video
Excellent engineering on this project, it does exactly what you designed. However I'm not a fan of this design. With your skills a proper vertical lift with tilt is easily within your skillset.
aquí en el estado de Guanajuato no hay tiendas oh ferreteras que vendan este tipo de material para hacer estás cosas, todavía estamos en pañales, aparte de que no cualquier persona tiene dinero para comprar y hacer estás cosas.
Está bonito el trabajo, lo que no me gusta de estos vídeos, es que vas siguiendo paso a paso pensando que con lo que tienes lo puedes hacer y luego sacan un generador termonuclear del cajón y uno no puede conseguir eso en la ferretería 🤷🏻♂️
영상 잘보았습니다~ 한가지 질문드려도 될까요~ 나무하고 철부속품하고 접착할때 사용하신 접착제가 뭔가요? 그리고 접착후 강도도 궁금합니다~ 아 그리고 ㅠㅠ 질문이 많아서 죄송합니다. 스테인리스 강판과 자작나무 합판을 접착할때 사용하신 실리콘(?)도 궁금합니다^^ 질문 많아서 죄송합니다~
관심가져주셔서 감사합니다
팬스 스톱퍼에 사용된 접착제는 2액형 에폭시고요 철제 접착시 매우 강력하게 접착되더군요 (다이소에서 2천원)
스테인레스에는 일반 실리콘 사용했습니다만 이것도 충분히 강하게 접착 되네요
@@letsdiy9521 답변 정말 감사합니다~
您必须参加工作课程的宏伟项目
Qq000
What dimensions did u use
좋은 영상 감사합니다.
테이블쏘를 만들려고 하는데 엄두가 안납니다. 공방의 꽃 테이블쏘 직접 만드셨다니 뿌듯하시겠습니다. 거리가 멀지 않으면 한수 배우고 싶네요.
댓글 감사합니다ㅎㅎ 제가 누글 알려드릴 실력까지는 안 되요
테이블쏘는 정밀도가 중요한 기계라 만드는 (시간 많이 걸림)걸 즐기시는 분이라면 도전해볼만 하지만 그렇지 않으면 기성품 구매를 추천드립니다
Smooth in every move you made .... Keep the good work sir.... All the best in ur next project.... Big big thumbs up👍💪
Very nice looking table saw. And strongly built. Will withstand years of heavy use, I'm sure! Thank you for sharing!
Thank you for your interest in my video!
진짜 금손이시네요.
영상 봐주셔서 감사합니다 ㅎㅎ
I've seen the same design of table saw in a few other channels. It's nice and I must say this is the best looking among them. But how can you tilt the saw?
buenas noches señor muy buena su aportacion sobre la fabricacion de esta sierra de mesa es para las personas que nos gusta la carpinteria pero no tenemos la manera de como adquirir una herramienta a veces costosas gracias por su tiempo y amabilidad de compartir sus conocimientos, felicitaciones, DIOS lo bendiga, saludos desde huatabampo, sonora, mexico
Thank you very much for the good comment
Ficou excelente parabéns.
Você fabrica pra vender,estou interessado em comprar?
산소절단 하시는 솜씨 보니 아마추어가 절대 아니신대요.
전직이 뭐하시던 분이신지 몰라도 멋지십니다.
어흑... 딱 산소절단만 제가 한 게 아니고 을지로에서 철판 판매 사장님이 자르시는 것을 촬영한 거에요 영상이 자세하지 못해
그렇게 보여질 진 것 같네요 아무튼 댓글 감사합니다
좋은 영상 감사합니다.
좋게 봐주셔서 저도 감사합니다 ㅎㅎ
Amazing portable table saw!!
좋은영상 감사합니다
Essa ficou muito melhor que qualquer outra máquina comercial.
Parabéns
hello
Thanks for watching
잘보고 갑니다.
승승장구하시길 응원합니다 ^^
영상 봐주시고 진심어린 말씀도 감사드립니다 ㅎㅎ
Отличная работа! Спасибо!
thanks for the nice comment
Good job sir, one big salute to you.
Thank you for your interest in my video
ABSOLUTELY THE BEST ON TH-cam.
Thank you very much for your interest in the video
Muito bom seu trabalho gostei tmj sucesso
창의적이고 아름다운 알루미늄 부품을 보여주고 싶습니다
Awesome build👍
Thank you for your interest in my video
Bravo man good precious job 🎩 ghany from Algeria thanks.
Thank you for your interest in my video
@@letsdiy9521 thank you.
Congrat perfect work
Thank you very much
Badass! Only need to add a tab behind the blade so you don't run the risk of kick backs due to the possibility of tension in the wood and closing onto the blade sending the wood into your face or nuts!
Esto es muy profesional, me has dado una idea para hacerme una sierra casera, like!
Thank you for your interest in my video
Excelente trabajo saludos deste bolivia 🇧🇴
Thank you for your interest in my video
Cordial saludo y felicitaciones por este proyecto tan precizo y funcional.
Desearía saber más de de la potencia motor, dimensiones etc, las especificaciones técnicas del proyecto pero en inglés o español de ser posible.
Desde Colombia un abrazo y me suscribo con like.
Thank you for your interest in my video
Single-phase , 220-240V , 60Hz , 3600RPM 1.5Kw(2HP)
Have a good day
Se puede compra lucir tarde cortr
추카추카😁백만조회 넘었네요!!!!
언제나 관심가저주셔서 감사합니다 ㅎ
Great job! Cool!
Thank you for your interest in my video
Good job my friend 👍😜
Congratulations ! Very very good beautiful.
Thank you for your interest in my video!
I think using the cnc track for fencing is a great idea. I am adapting a table saw to use these. Great pro build, thanks for sharing.
be sure to succeed thanks for watching
Top de mais amigo 👏👏👏
thanks for the nice comment
very good its nice job. iam from algeria.
Thank you for your interest in my video!
Exelente trabajo amigo saludos desde huánuco Perú...por favor podría enviarme los planos en PDF ó programa SketchUp gracias y muchas bendiciones para usted
Unfortunately, the file is inaccurate and I can't provide it. Sorry
Very good job
Thank you for those kind words
Great job. Can I have the plan of it and what the items do u used
-Parts Used-
Bearing shaft
Single-phase , 220-240V , 60Hz , 3600RPM 1.5Kw(2HP)
Bearing shaft
bearing
Square pipe
Aluminum profile 4080x 800mm
Thank you for your interest in my video
making a table saw using another table saw and a bunch of other tool
where you get a stainless steel plate
Hi, is it possible to ask for a list of materials you used in this build?
Parts Used
Bearing shaft
Single-phase , 220-240V , 60Hz , 3600RPM 1.5Kw(2HP)
Bearing shaft
bearing
Square pipe
Aluminum profile 4080x 800mm
Thank you for your interest in my video
Прекрасная работа, но циркулярная пила без наклона диска имеет урезанный функционал. Если уж делать настолько качественно то и над механизмом наклона следовало поработать!
А так отличная настольная пила!👍
I can't add angle adjustment.Thank you for your interest in my video
Qual o valor? Dessa máquina?
Thankyou me urge aser mis propias herramientas .perdi mi empleo y necesario construir juego de sala, gracias a ustedes los youtubers como tu ,aprendemos mucho,mis hijos adolesentes y yo construimos mueble de concreto chorreando para fregadero de cocina, así que también podremos aprender con trigo gracias
Thank you for your interest in my video buena suerte siempre
Buenas, de Perú, FELICITACIONES buen trabajo de la Mesa circular, sería excelente considerar las medidas de dicha máquina y la sugerencia del motor de cuantos HP se utilizaría para un excelente trabajo. GRACIAS.
Thank you for watching the video with interest
Good is case study for job aluminum.
Super interesante el diseño. Que programa uso para el modelado 3D?
hello i work with sketchup
Far better than branded company's chipper material and low precision.
Thank you for your interest in my video!
Good job
what is the size of the table ? Thank you
Hello my friend.. I love this table saw u built bro. I have a couple of questions of u don't mind me asking u..??
Q. What are those bigger bearing holders called u used for the Blade lift.. U used 2 of them but I cannot for the life of me find any of them online. Could u drop a link for them on here if u have a minute?
I'm about to embark on a Table saw build of my own and I'm in 2 minds about what to use for the top/Table.. I like how u used the Aluminium but what width was that u used for the top of the table?? It looks awesome dude.
If I'm not mistaken u also use those Spiral tap bits too?? Are they better than the original type ones?
Anyways I wanna say how great ur table saw build is and thank u for inspiring me to get going with mine soon.
hello
I replied but it got deleted so I'll reply again
I translated the words you inquired into a translator and read them.
It's not an accurate translation, so I'll try to answer with a sense ^0^
Gcr 15 UCF203
ko.aliexpress.com/item/1005003777979794.html?spm=a2g0o.productlist.main.1.7d182ea1RlCJlg&algo_pvid=ad5c793f-9a79-46e2-b393-e82f6ea0ff98&algo_exp_id=ad5c793f-9a79-46e2-b393-e82f6ea0ff98-0&pdp_npi=3%40dis%21KRW%219195.0%217535.0%21%21%21%21%21%402145277316858830540082603d07b5%2112000027133823735%21sea%21KR%21888194637&curPageLogUid=BdJmtjokdJlo
The top/table size is 800x700mm.
The stainless plate on the birch plywood is 1T
When using an aluminum plate, it is recommended to use a product with a thickness of 2T or more.
thanks for watching the video
평소에 테이블쏘에 관심이 많았습니다. 영상을 보고 하나 갖고싶다는 생각이 들어서 비용이 얼마나 들어가는지, 제작은 제료구입해서 만들어야 되는지 궁금합니다.
제작 비용은 저렴하지는 않습니다 대략 50여만원 정도 들었구요 재료는 당연히 구입해서 만들었습니다 ㅎ
미끄러지는 방위는 먼지로 막히는 얻지 않을 것입니까?
please could you tell me what are the names of all the tools in this video?
-Parts Used-
Bearing shaft
Single-phase , 220-240V , 60Hz , 3600RPM 1.5Kw(2HP)
Bearing shaft
bearing
Square pipe
Aluminum profile 4080x 800mm
Thank you for your interest in my video
Excelente , pero para que sea un trabajo profesional le falta la protección del disco
Great job
Thank you for your interest in my video
Good day to all! To the author, many thanks for the interesting and useful video! Craft! Is the model made in SketchUP?
thanks for watching this video
As you said, it was designed with SketchUp.
Gracias🙏🙏🙏🤗🇨🇷
와.. 메카닉
Ôi thích quá dự định mua 1 cái tương tự v
This item is not for sale Buy ready-made products
Thank you for your interest in my video
Wow ! Awesome
Thank you for your interest in my video
금속처럼 보이는 저 판의 이름은 무엇이며 두께는 얼마입니까?
What are the names and sizes/ diameters of the parts shown here at 7:30, please? ✌🏻
The name you asked is SBR16 (16mm)
Please refer to the link for details
ko.aliexpress.com/item/32959168912.html?spm=a2g0s.9042311.0.0.27424c4d8t7R0g
excuese you can tellme whats the name of the program? or desing software
This is SketchUp Thank you for your interest in my video
buat tabel saw pakai tabel saw dan alat2 canggih.seharusnya klu untuk rumahan alat2 seperti itu tidak ada.skiplah untuk video ini
Very Nice subarashi 😊
Keren
Mantab
Top
Excellent engineering on this project, it does exactly what you designed. However I'm not a fan of this design. With your skills a proper vertical lift with tilt is easily within your skillset.
I'm very sorry too
but i don't have that skill
aquí en el estado de Guanajuato no hay tiendas oh ferreteras que vendan este tipo de material para hacer estás cosas, todavía estamos en pañales, aparte de que no cualquier persona tiene dinero para comprar y hacer estás cosas.
Lo siento
Sea fuerte de todos modos!
사장님 그기계 하나만 주문하면 안될까요
Está bonito el trabajo, lo que no me gusta de estos vídeos, es que vas siguiendo paso a paso pensando que con lo que tienes lo puedes hacer y luego sacan un generador termonuclear del cajón y uno no puede conseguir eso en la ferretería 🤷🏻♂️
Thank you for your interest in my video!
하~떵손은 어떻게 해요 ㅜㅇㅜ...
재료 설명도 해주셔요~~
저도 마찬가지입니다ㅎㅎ 재료는 영상에 다 나와있어요 잘 보시고 필요한 부분만 말씀해 주시세요~
Por favor me podrían mandar las medidas de la sierra circular pequeña de todo de donde va la base del motor y la chumasera en español
선형레일? 슬라이딩? 저건 어떻게 제작하셨나요? 부품을 구입하셨다면 알려주시면 감사하겠습니다.
선형 가이드 레일 + SBR16 2pcs 국내는 비싸서 알리에서 구입했습니다
ko.aliexpress.com/item/32959168912.html?spm=a2g0s.9042311.0.0.27424c4d8t7R0g
@@letsdiy9521 한동안 어찌 만드나 고민했는데, 정말 감사합니다!
this tools is awesome
it is possible to get your sketch files with plans ???
Best regards Patryk
Thanks for your interest in the video.
However, we cannot provide it due to the poor accuracy of the drawing.
Пчень хорошо!
상용화가가능할까요?
현장용으로...
너무조용하고부드럽습니다!
상용용으로는 절대 안됩니다
개인 취목용으로 대충 만든거라서
안전 장치도 부족하고 모든게 주목구구식입니다 ㅋㅋ
조용하기는 한데… 정밀도가 좀 마음에 안드네요..
왠만한 상용 제품보다 훨씬 안전하고 정밀해보이네요^^
조깃대나 날 정렬 틀어진 상용 제품도 허다한데 이미 diy 수준은 아닌듯합니다
좋은 영상 감사합니다
Se ve bien hecho... Pero creo que mejor me compro uno ya hecho... No tengo ninguna de esas herramientas y menos el material acanalado... 😭
Muito bom 👍 👍
모터 구입처 알수있을까요 첨부터 영상3번째 자세히보는중입니다 ㅎㅎㅎㅎㅎ
I love idea
wow,heavy duty machine
Thank you for your interest in my video
Best vedio brother
精度很高,很不错得方案.
thanks for the nice comment
Excelente
Kindly give the drawing in the Sketch Up program
Sketch Up file cannot be provided because it is not accurate
Please understand
@@letsdiy9521 Thank you, I am one of those who follow your wonderful works with success
기성품 보다 조금 조용한거 말고는 매리트가 없어보이네요 공수며 자재값 하면 보쉬 테이블쏘 사는거 보다 훨씬 비싸게 치인듯 보이네요 것다가 각도 조절불가...ㅜㅜ 손제주는 인정ㅋ
네 맞습니다 정확히 잘 보셨습니다 가성비 제로에요 온니 정숙성 하나보고 시도한 겁니다
얼마 전 지인 공방에서 쓰는 쏘스탑을 보았는데 엄청 탐나더군요 그 정숙함이
그런데 가격이 취목 하기에는 엄두가 안 나는 금액이라 한번 만들어 보았네요 ㅎㅎ
멋진 테이블쏘를 제작하셨네요.
집진은 안하신것 같은데 내부에 분진은 어떻게 해결하셨나요?
안녕하세요 영상에는 빠진 것 같습니다만 최대한 밀폐시키고 뒷면에 진공 청소기를 연결할 수 있게 포트를 달았습니다ㅎ
Awesome
Làm máy bào cuốn tự chế đi bạn
모터 몇마락 또가격이
궁금 합니다 알려주세요
2마력 모터고 중고 8만원 줬습니다 (청계천 8가)
Very nice
Thank you for your interest in my video👍
Hello, how thick ist the plywood and sheet metall from the top?
Thank you for your interest in my video
Wood plywood is 18 mm.
Iron plate is 2mm
@@letsdiy9521 thank you for your quick answer. How big is the sawblade and how much cutting depth do you have?
Sorry, the stainless steel plate is 1mm thick
@@karolb.3831 The saw blade is 10 inches.
The cutting depth can be up to 75mm
which sofware you did to design?
I used sketch up Thank you for your interest in my video
Good 😊
Thank you for your interest in my video😊
👌👌👌
so you need to buy an entire table saw to make another table saw..?
Чудовий задум і виконання!
Thank you for your interest in my video
may i ask what solfware you using ？
I used SketchUp Thank you very much for your interest in the video
You need a table saw to make a homemade table saw. Got it.
Thank you for your interest in my video
...and other expensive tools
소리가 얼마나 작은지 비교가 안되니 알수가 없긴하네요.. 모터는 몇 와트인가요?
소리 크기는 조금 더 정숙하다고 보시면 되고 모터는 2마력입니다
관심 가져 주셔서 감사합니다
이야!!! 정말 멋져요. 기왕 베푸시는(?)차에 스케치업 파일도 공유해주시면 極감사할 것 같습니다. :)
스케치업을 처음 사용해보는 거라 매우 서툴러서 치수도 안 맞고 정확하지 않아 공유하기에 무리가 있네요.. 영상에 관심 가져 주셔서 감사합니다. ㅎ
엄지척!