Sir reactor mai kun kun sa maintenance kaise karte hai jaise seal kab khrab hota gear kun sa hota hai pura ek complete video maintenance pe baniye usme eccentricity kyu karte hai
भाई मेरा एक सवाल है यदि रिएक्टर मै ज्यादा प्रेशर हो जाता है तो क्या होगा ना ही हमे प्रेशर रिलीज करना है ना ही हमे vante देना है ऐसे मै क्या होगा please बताए
Glass jo tenk hota he us ke uparvala jeket kharab ho gaya he to us ko naya jeket banake dalna he to kese kare ki andar vala glass ko koi nuksan na ho jeket ko ges kating kar sakte he
My point of view ..jab koi bi reaction krni hogi to heating ya chilling di hogi to Jada thickness ke wajah jitni chaiye utni nai milegi tym Jada lagega
Dear it is basically optimized value depending upon heat transfer rate ,Glass and metal bending thickness strength.Even costing is being considered for the same.
Thank you for the super knowledge, Sir
Dear Thanks...
Thank you so much sir you are give very important knowledge
Dear Thanks....
Super knowledge shared
Dear Thanks
Topic is very knowledgeable
Dear Ramavatar thanks...
Very good information sir
Dear Rushikesh Thanks....
👍
Dear Thanks...
@@ChemicalMahi any contact no???
Sir reactor mai kun kun sa maintenance kaise karte hai jaise seal kab khrab hota gear kun sa hota hai pura ek complete video maintenance pe baniye usme eccentricity kyu karte hai
Dear sure very soon...
Nic information .Ye sabb maintenance hamare company Mai hua hai
Dear Nikhil Thanks...
@@ChemicalMahi aur kuch imp topic pe video banao GLR pe
Dear Sir pls make vedeo on SS reactor
@@nikhilsankhe3871hi i want to get in touch with you
Dear sir PDF ka free me nahi ho sakta aapka har video achha hota har video ka PDF hame mehga par jayega
Dear Safyan it's just nominal charges.This I give to some government organisations that help for poor.
pfa line masrum se tight kar raha hu but niche joint sealant se leakage arha hai kya karu
भाई मेरा एक सवाल है यदि रिएक्टर मै ज्यादा प्रेशर हो जाता है तो क्या होगा ना ही हमे प्रेशर रिलीज करना है ना ही हमे vante देना है ऐसे मै क्या होगा please बताए
Dear Then in that case is Presssure passes the designed Pressure of Reactor then it will brust or Leak from the weakest Point.
Why SS not used instead of MS/CS as outer metal ???
Dear Himanshu due to cost issue.
Pranam sir ji 🙏🙏🙏🙏
Sir diploma chemical engineering k liye psu k liye course h please🙏🙏 sir bataye
Dear Sandeep No.
Glass jo tenk hota he us ke uparvala jeket kharab ho gaya he to us ko naya jeket banake dalna he to kese kare ki andar vala glass ko koi nuksan na ho jeket ko ges kating kar sakte he
Vessel ke sathe jo seler ring lagi hoti hai use chodkar kar sakte hai. 3 inch during se kar sakte hai.
Sir GLR Ka Damage Repair karne ki Training kaha se le...Plz reply me
Dear suhita u can contact any Glass lined Reactors vendor....
Why green glass uses above 270 c
Daer Composition of glass changes for various temperature range that may be a reason for green colour.
Why thickness is 1 to 2 mm??
Why not more than?
My point of view ..jab koi bi reaction krni hogi to heating ya chilling di hogi to Jada thickness ke wajah jitni chaiye utni nai milegi tym Jada lagega
Dear it is basically optimized value depending upon heat transfer rate ,Glass and metal bending thickness strength.Even costing is being considered for the same.
Sir damage GLR repair contact number ho to send kar dijiye please sir