Seus vídeos, seus trabalhos são muito bons... Sua técnica de execução, a produção dos vídeos e principalmente como aprender com os detalhes que são claros.... parabéns....
The biggest problem I found with making doweling jigs is the high precision required in the build because when you use the same jig for opposing joints, any inaccuracy in the jig will be doubled, resulting in misaligned joints. This pair-use jig solves that problem!
Does the accuracy of the connection is not affected by a large error 7:05 in the manufacture of the jig? Разве на точность соединения не влияет большая погрешность 7:05 в изготовлении джига?
@@jisakukobo Добрый день! Я с интересом отношусь к вашим видео и с большим уважением - к вашему мастерству. Моё сомнение - не отрицание, а только сомнение. У меня нет такого опыта и практических навыков. Тем не менее, я использовал шканты в несложных домашних работах. Исходя из этого небольшого опыта и школьного курса геометрии (правда, это было очень давно))) я и высказал свои сомнения. Если вы делаете отверстия от руки, без использования стабилизирующего устройства, вы неизбежно получите погрешность (вы получите её даже при использовании различных приспособлений - речь идёт о том, можно ли ею пренебречь, или она повлияет на качество соединения?) Эта погрешность приведёт к тому, что оси отверстий не будут параллельны друг другу и не будут перпендикулярны плоскости базы и заготовки. Остаюсь вашим благодарным зрителем! Good day! I am interested in your video and have great respect for your skills. My doubt is not denial, only doubt. I have no such experience and practical skills. However, I used dowels for simple home jobs. Based on this small experience, and school geometry course (though it was a long time ago))) I expressed my doubts. If you make holes by hand, without the use of a stabilizing device, you will inevitably get an error (you will get it even when using different devices-is it possible to neglect it, or will it affect the quality of the connection?) This error will cause the hole axes not to be parallel to each other and not to be perpendicular to the base and workpiece planes. I remain your grateful audience!
It does not have to be parallel or vertical. It is only necessary that the axes of the two are matched. I can not explain it in Russian. Someone, please give him a description in Russian.
@@jisakukobo Благодарю! Конечно, на родном языке удобней )) Но на эту минуту для меня всё понятно. С вашим аргументом я, конечно, согласен, но он справедлив только по отношению к одному шканту. Если имеем в соединении два шканта и более - они должны быть параллельны. Таково моё заблуждение на данный момент, простите )) Желаю успеха! Thanks! Of course, in my native language is more convenient )) But at this moment everything is clear to me. I agree with your argument, of course, but it is only fair to one shkant. If you are connecting two or more peg - they should be parallel. Such is my misconception at the moment, sorry )) Good luck!
Take time making the jigs, they last for a long time, with care, save lots of time too when making right angles for cabinets especially.Great show, Thank you.
Узнаю уже твои видео по рукам и манере движений! Эти видео меня гипнотизируют! Можно узнать в каком городе ты живешь и какая у тебя профессия? I already recognize your videos by hand and manner of movement! These videos are mesmerizing! Can you find out what city you live in and what your profession is? 私はすでにあなたの動画を手と動きの方法で認識しています！ これらのビデオは魅惑的です！ あなたが住んでいる都市と職業を知ることができますか？
Drill the both piece together with a single system = more fast an more precize! Good usual for You mr MMAGIC HANDY MAN isn't it! Thank again, more cheap than the works shop
very nicely done, I must try making this jig for myself. I noticed the small table saw and several commenters have asked about it. Which saw is it? it looks great, very helpful for small work. Also, I like the music very much, good choice.
So for t-joining you'd make a dowel jig where the holes are horizontally spaced from the resting guide, instead of vertically thou for more uses instead of it being one jig with 2 holes, make 2 identical jigs with only 1 hole, otherwise you're limited by the width of the boards i.e you had a 15 cm wide board, you'd make a hole guide jig with 5 cm's space between them and if it's 8 mm thick dowels 8,2 cm spacing on either end, but if your next project calls for 12 cm wide boards then that would throw it All out of alignment
I was wondering the same, but it would probably be metric and here in the states we are still behind on weights and measures so I will probably just match a bit to dowel size and tube.
If you find any unauthorized reproduction of the JSK-koubou video, please report it to me.
Thank you.
JSK-koubouビデオの無断複製を見つけた場合は、報告していただけると助かります。
Seus vídeos, seus trabalhos são muito bons... Sua técnica de execução, a produção dos vídeos e principalmente como aprender com os detalhes que são claros.... parabéns....
Simple but effective 🙂
د
قطط
amazing result. you shown a clever way to compensate for not so straight hand drilling. the two pieces fit together perfectly.
Jig should be made like this as a pair so the guided holes do not need to be perfectly vertical. this is brilliant.
世界中の言語が見えます♪息子よりずーっと若い方ですが全ての動画にアイデアが溢れています。加工方法と作り易さと高精度が見てとれます。言葉は要りません。海外の動画はプロのカメラマン？に撮影してもらい自分がスターになった気分で話が多すぎる。この様な動画に興味のある方は見るだけで理解出来るのにと思います。それと安価で出来て特に高級な工作機等は使わない。これが一番かな？いや全てが一番です。
Good my brother💖💖💖👌👌🇮🇳🇮🇳
Pure skills. I just find It amazing how you drilled those holes almost perfectly perpendicular using only hand held drills.
Superb bro, very easy , prevent us wasting money
Good you work 👍👍👍👍🥇🌟🌟🌟🌟🌟
Великий мастер!!! Приятно смотреть как ты работаешь!
私は韓国人です。毎日見ています、本当に周りが端正で、作品が高級にみえますね。私の先生です。日本語が下手のですみません。
Great product! I’m going to make one tomorrow. Thank you.
🎓Exellent main frend👌
my greetings from serbia
👍👍👍👍👍👍👍👍👍
Excellent accuracy and workmanship thank you
Brilliant! What clever engineering, taking advantage of the reference surfaces so the holes always match!
Amazing joint with amazing jig.
Super.
And i thought i was good but you are brilliant. This actually works despite the error of hand drilling. I couldn,t have thought of it. Congrats...
My headaches just left ME.thank you sir.simplicity sensation at best. And freehanded.tip of the hat. El Tejano
The biggest problem I found with making doweling jigs is the high precision required in the build because when you use the same jig for opposing joints, any inaccuracy in the jig will be doubled, resulting in misaligned joints. This pair-use jig solves that problem!
Wonderful. So easy to make. Thank you for sharing.
Awesome! I don't have a drill press and so happy I'll be able to make a dowel jig anyway . Thank you!
字幕で動画の説明をしています。
I explain the video with subtitles.
字幕をONにすると分かりやすいと思います。
I think that it is easy to understand by turning on subtitles.
自作工房 only Japanese subtitles are available. Though the process seems pretty clear so far.
It is in translation, but it will take some time.
For now, please visit youtube for automatic translation.
@@jisakukobo I agree with seth, the video is pretty self explanatory, well done.
Very nice video❤❤❤❤
It's a very nice idea. I like simple technics.
Beautiful Jobwork 💗
Does the accuracy of the connection is not affected by a large error 7:05 in the manufacture of the jig?
Разве на точность соединения не влияет большая погрешность 7:05 в изготовлении джига?
Why do you think so?
I am shooting video to prove that it works properly with movies.
Are not you watching a movie?
@@jisakukobo Добрый день! Я с интересом отношусь к вашим видео и с большим уважением - к вашему мастерству. Моё сомнение - не отрицание, а только сомнение. У меня нет такого опыта и практических навыков. Тем не менее, я использовал шканты в несложных домашних работах. Исходя из этого небольшого опыта и школьного курса геометрии (правда, это было очень давно))) я и высказал свои сомнения. Если вы делаете отверстия от руки, без использования стабилизирующего устройства, вы неизбежно получите погрешность (вы получите её даже при использовании различных приспособлений - речь идёт о том, можно ли ею пренебречь, или она повлияет на качество соединения?) Эта погрешность приведёт к тому, что оси отверстий не будут параллельны друг другу и не будут перпендикулярны плоскости базы и заготовки. Остаюсь вашим благодарным зрителем!
Good day! I am interested in your video and have great respect for your skills. My doubt is not denial, only doubt. I have no such experience and practical skills. However, I used dowels for simple home jobs. Based on this small experience, and school geometry course (though it was a long time ago))) I expressed my doubts. If you make holes by hand, without the use of a stabilizing device, you will inevitably get an error (you will get it even when using different devices-is it possible to neglect it, or will it affect the quality of the connection?) This error will cause the hole axes not to be parallel to each other and not to be perpendicular to the base and workpiece planes.
I remain your grateful audience!
It does not have to be parallel or vertical.
It is only necessary that the axes of the two are matched.
I can not explain it in Russian.
Someone, please give him a description in Russian.
@@jisakukobo Благодарю! Конечно, на родном языке удобней )) Но на эту минуту для меня всё понятно.
С вашим аргументом я, конечно, согласен, но он справедлив только по отношению к одному шканту. Если имеем в соединении два шканта и более - они должны быть параллельны. Таково моё заблуждение на данный момент, простите )) Желаю успеха!
Thanks! Of course, in my native language is more convenient )) But at this moment everything is clear to me. I agree with your argument, of course, but it is only fair to one shkant. If you are connecting two or more peg - they should be parallel. Such is my misconception at the moment, sorry )) Good luck!
そうですね。3つ以上のダボがある場合、理論上は平行でなければ入りません。
しかし、（金属ではなく）木材なので、極端にダボが曲がっていない限り入ります。そして、入ってしまえば正確に接合できます。
Hola gracias por sus enseñanzas, sencillo fácil y agradable. Saludos desde Colombia.
Buenas tardes me dirias de que tamaño es el tarugo y la varilla que cortaste?, gracias muy bueno el video
You really smart about dowels kit 👏👏👍👍
Take time making the jigs, they last for a long time, with care, save lots of time too when making right angles for cabinets especially.Great show, Thank you.
Узнаю уже твои видео по рукам и манере движений! Эти видео меня гипнотизируют! Можно узнать в каком городе ты живешь и какая у тебя профессия?
I already recognize your videos by hand and manner of movement! These videos are mesmerizing! Can you find out what city you live in and what your profession is?
私はすでにあなたの動画を手と動きの方法で認識しています！ これらのビデオは魅惑的です！ あなたが住んでいる都市と職業を知ることができますか？
Uma pregunta, si la madera a perforarar hay que hacer una plantilla para cada espesor de madera.
Brilliant!
I also love that fine work little table saw.
Very good 👍🏼
I love your videos!
Thanks will make them, as the jig I've got is rubbish and been practicing before I wast good wood.
How can we test economic models of the forest sector?
Drill the both piece together with a single system = more fast an more precize! Good usual for You mr MMAGIC HANDY MAN isn't it! Thank again, more cheap than the works shop
I made this today. Works Great ! Thankyou !
Cuáles son las medidas para hacer la plantilla para los tarugos
Very good working!
muito legal!!! Parabéns!! Voce poderia passar as medidas e materiais utilidados?
Só saber onde comprar esse caninho!!
Very neatly done and just what I was looking for. Thank you
love you guys.
Excellent job and video too! thank u
I did it and work perfect. Thx for sharing mate.
What's the musical trailer title plz.
It is amazaing! Brilliant idea! Thank you
Master, which table circular saw do you use? Proxxon?
Really enjoy this video thankyou, it still comes down to how precise I can drill these holes
you don't have to drill these holes perfectly - that's why his solution is such a perfect one.
Thanks. Congratulations. Good job
Well presented Video !
動画を見てあーなるほど、そうかその手があったかと感服しました。
頭良いですね。これなら同じようにずれるから結局合ってきますもんね。
もう一つの方法として、角材に穴を開けて中心で2分割に切断する方法もあります。
こちらは少し大きな丸鋸やバンドソーが無いと加工できないので動画にしませんでした。
参考になれば幸いです。
very nicely done, I must try making this jig for myself.
I noticed the small table saw and several commenters have asked about it. Which saw is it? it looks great, very helpful for small work.
Also, I like the music very much, good choice.
Por favor traduza para português também 🙋🏻♀️🇧🇷👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻
De que medidas es la madera y los tubos qué largo y que diámetro gracias
Лайк. Отличная задумка👍👍👍
What kind of table saw is that?
Alguna con rodamientos 608 de 22 mm?
Genious. No need for drill press
Je ne vois pas comment utiliser ce gabarit pour le milieu du T ... J'ai loupé une explication?
Es muy interesante el proyecto pero para mi faltan las medidas gracias.
Thanks for publishing it! That's the solution I was looking for! Cheers!
comme d'habitude, solutions simple et élégante
Muy buena la idea,pero no veo ninguna medida.trozos de madera,largo y diametros de los tubitos.
no muestras las dimensiones de la madera y diametros de perforaciones
Thanks for the subtitles.
Great job
Gostei muito bom
🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷👍 Thanks you my friend
hi I like youe precise work, what is the double stick tape you are using? you have a link?
Absolutely brilliant. Thank you.
excelente idea es de mucha ayuda amigo gracias por el vídeo saludo desde Colombia!!!
Почему не указываете размеры и как использовать вашу работу?
Thank you for sharing your great expertise
guaooo gracias desde mi querida venezuela
donde se puede ver las medidas de las maderas gracias
Bravo !!! c'est super *****
Me gusta👍👍
Lo bueno es que esta doblado al español
A simple and clever solution. Well done!
I still don't understand how will you get the holes straight without a. Drill press?
Perfectly square is not necessary. Alignment is the most important part and the two blocks are aligned while drilling.
Brilliant first class
Gracias por el aporte y vídeo, por fin traductor gracias.......
very precise finish .thanks tony thomas
당신은 훌륭합니다.
Thank you. This is a fantastic solution. I really enjoy your videos.
Секс фильма
Фильм о классическому
сексе
That's so clean and accurate wow
How can so much perfection fit in one man? Amazing work...México
excelente!!! saludos desde buenos aires!!
Very good idea..
What is the Music trailor name please.
Useful information
סרטון מעולה ברור וחשוב. המון תודה לך.
Just brilliant. Very neatly done and just what I was looking for. Thank you. Subscribed.
Louvado seja Deus que te criou e bendito os seios que te alimentaram meu amigo!
The video never showed how to make the matched jigs for the T junction, just the corner piece
Sure, the T junction jig is not so straight forward
So for t-joining you'd make a dowel jig where the holes are horizontally spaced from the resting guide, instead of vertically thou for more uses instead of it being one jig with 2 holes, make 2 identical jigs with only 1 hole, otherwise you're limited by the width of the boards i.e you had a 15 cm wide board, you'd make a hole guide jig with 5 cm's space between them and if it's 8 mm thick dowels 8,2 cm spacing on either end, but if your next project calls for 12 cm wide boards then that would throw it All out of alignment
Thanks for that brilliant idea. The sound of your electric drill is like a music in my ears.....hope i had that kind of High Quality drill/tools.
What size of a hole?
What a great idea!!!! Thanks
If the jig is made for T junction then it should have been shown to be working with the T junction and not the right angle.
Dimensions would be helpful, especially spacing of holes
what is the diameter of metal sleeve? Is it stainless steel sleeve?
I was wondering the same, but it would probably be metric and here in the states we are still behind on weights and measures so I will probably just match a bit to dowel size and tube.
8 mm
Excelente
Gracias por la enseñanza