TSP
ฝัง
- เผยแพร่เมื่อ 27 ส.ค. 2024
- In this episode Shahriar repairs an IFR (Marconi) 5GHz programmable attenuator capable of reaching a maximum of 130dB attenuation in 1dB steps. The Instrument does not power on and a teardown reveals some missing components inside. After replacing the missing component, the instrument powers on but the S-Parameters show that the mechanical attenuators have serious contact problems. Finally after cleaning the attenuator contacts, the instrument is fully operational. The unit is used to measure the performance of the Keysight MXR at very low input signal powers.
www.TheSignalPath.com
/ thesignalpath
www.Patreon.com/TheSignalPath
*Please note that the two attenuator modules are not identical. They are used in sequentially and in conjunction to achieve 1dB steps across the entire 130dB variable range. This is one of the main advantages of this instrument to provide small steps and very large range.*
Man, you forgot to say "FIIRRRSST!"
Interesting repair - it seems the first test of any of this high frequency equipment should be to see if you've got a low-pass problem - seems like a theme! Nice repair and experiments.
Hehe… By the way, I’d like to repeat the sensitivity experiment with the 6B and the demodulation software. When do you think that would be available?
@@Thesignalpath It's available now - I'll be in touch...
"Be careful cleaning this" Doesn't show him cleaning it. This would be such a useful step to observe for those of us in industry who have never been taught these techniques.
Exactly
If you're in "industry", just buy another one, and let the broken one trickle down to us mere mortals who can't afford to pay full price for RF test equipment, but have the time to fix the broken stuff.
@@gorak9000 please tell me you're a troll, do you think all of the electronics industry is just awash with money, some of our kit costs as much as a small family home and you think we're just throwing it away?
When I saw that DC wasn't getting through, I was sure the issue was going to be another bad front panel connector.
Glad that it was not!
Your teardowns are the best because you _actually_ fix them a lot of the times!
Full bridge rectifier made me laugh. You need to show Mehdi's face every time you say "Full Bridge Rectifier" :)
This one was so great, and so approachable. I love the variation between the technical-heavy videos and the ‘simpler’ mechanical fixes like this. I’m very happy to support this type of work through the Patreon!
Thanks, Shahriar. As a hobbyist with little RF knowledge, I'm always fascinated by your tear-downs, repairs and experiments. You must have one of the most well-equipped and valuable home electronics/RF labs on earth, but what do you use it all for? Are you satisfying your own hobby interests, developing products, or do you bring work home that you can't reveal publicly? Any chance you could show us how such a mind-boggling home lab is actually used, beyond eBay repairs? Looking over your shoulder through a full project development would be awesome. Cheers!
Always enjoy your repairs, well done!
Glad you like them!
Would have been helpful to see the procedure you took to clean those contacts.
The frequency can be used to read the calibrated attenuation value at that frequency (from display or Ieee interface). If you switch on "corr mode" it will try the set att value as close as possible for the given frequency. E.g. the display will show 100dB but internally it will set 99dB as that is closer to 100dB for the given frequency.
Innas cable guy , Just out of curiosity... you knew this how?
@@BruceNitroxpro i used this attuator long time ago testing e.g. RF amplifiers
@@hnasje66 , Aha... this is a very lovely instrument and has great specs. I wonder how much it cost back in the day?
I wasn't watching the video when you said "full bridge rectifier" but I knew enough to rewind a few seconds and look for a visual electroboom reference ;-)
Dr Tune , That was a low blow! ROFLMAO
@@BruceNitroxpro it's pretty much a requirement of any electronics vlog to honor the meme
@@DrTune , I guess I should say that Electroboom is da man! I thought the laughter said that, I guess not so well!
The design of the PSU and the logic board is very similar to my Marconi Instruments 2435 2GHz frequency counter. Cool!
My personal mechanical attenuator failures are:
little O rings that dampens the movement.
The pin might not be at the right place in the tiny slit
Dirty contacts , most frequent
Only once I had a die that did not work.
phool-bridge rectifier!
Could you please include in your tests something that tests the device way past their rated frequency range? There are so many quality items on the market that behave very well even outside of their specified parameters. It would be very interesting to see which devices work well at higher frequencies, and which ones don't work well at all. Considering all of these devices are purchased used, it would be so helpful to get the most out of them. Like this attenuator, I wonder if one could go do 9Ghz and have it still be usable, etc. Thank you.
If it's possible to damage some devices by putting too high frequency into them, then you'd end up having to test them to failure to find their performance outside their rated frequency. Another possible issue is that they might perform differently at different signal levels and frequencies and it would be too time consuming to characterize their performance across all parameters.
That said, I'd love to see how they perform at higher frequencies, especially if it has a linear rolloff, you could find the -3dB point and use that to calibrate out the additional attenuation from the device on top of the attenuation you program.
If it's missing a FUUUULLL BRIDGE RECTIFIEEEEEER then it belongs to Electroboom 😉
Aren't these moveable strip lines more operating like CPW (Coplanar waveguides) with side grounds !!?
Instead of coaxial due to moving center conductor !!?
0:12 I really would like to know what dumpsters you have.
Does the freq button do anything?
I'd like to know that, too.
The people have a right to know!
It did nothing! :)
@@Thesignalpath that's a shame. I was hoping they'd at least snuck a free simple frequency counter or something in there!
@@Thesignalpath It's to compensate for the actual loss at a given frequency, since the frequency response isn't completely flat from DC to 5 GHz. For example, setting the programmable attenuator to 10 dB may require setting 9 dB of face value with 1 dB of additional internal loss.
just wonder what is the algorithm of equalizer parameter , how we do know to adjust those parameter for equalizer ?!
That was an amazing video! How did you clean the attenuator contacts? Can you use something like Deoxit?
I'm guessing the full bridge rectifier was scavenged after the instrument was found to not be working.
Yes, it is likely.
@@Thesignalpath I still find it to be odd. You can get a 15A rectifier for $1, and I can't imagine the one in this instrument to be that big. Perhaps they needed something right away?
What causes the contact to fail? Carbon buildup or pitting?
Just aging. It not perfectly hermetically sealed.
I'm curious as to why spraying contact cleaner would ruin the attenuator. Would you please explain why.
Are the attenuator units using binary values to produce all the attenuation steps? (MSB-LSB).
Binary steps would allow the minimum number of fixed attenuators and switches, but not necessarily the minimum number of switch actuations, since that's a wear item, a point of failure, and also may maximize tolerance stack up errors where the insertion loss differs by the face value. It's also helpful for the engineer to know where the bigger attenuator steps are, since the errors are larger when switching those in and out. It's convenient for us base 10 creatures to have those large steps occur on 5 dB or 10 dB boundaries.
Not another of those simple faults 😀 (The rectifier)
Great video! what cleaner did you use?
Is that display you attached just a touchscreen or a whole pc?
I am looking for a small device like that if its just a touchscreen and no pc build in.
Please let me know what it is and where i can geht it. Thanks!
Yes, just a small LCD. Just search on Amazon for 7” LCD.
5:05 I don't think that Philips capacitor will die in the next 20 years (Vishay now if I look at their design that looks identical) :P