Hello Fellow colleagues. If you enjoy the video please click that like button and if you did not, dislike it and let us know in comments, what was, that made you not happy with the content, so I can learn from it and make better videos for you in the future. Have a great day everyone.
can this drive be run on 0 - 3.3v? Eg. putting it in 0-5v mode using Al1 and com and somehow making the drive run at 100% when it reaches 3.3 and hold all the way to 5v?
Hola me prodrias guiar en lo siguiente, ese variador esta en una talanquera de peaje, en uno muestra falla E01, E02 en otro la E13 en otro el display parpadea en FCS, y no logro encontrar como una listado de fallas o errores
Very grateful for this video. Just little slower & clearer would be great. Your European accent is a little hard to follow. Pretty sure I have set mine up properly however I had to watch it many times. So just a bit slower with less malarkey for the non electrical engineer like me. Thanks again.
Fantastic video. You mentioned that you are able to set a higher HZ in the vid. I have tried that but can not get my motor to spin up past 50 Hz. I want to go to 200 Hz. Do you have any clue to why not?. Best regards Thomas
HI There. There is 2 types of frequency in your drive. One is base frequency that can only be 50 or 60 and other is run hz. Change your max frequency to hat ever you need and you should be good to go, believe i mention in video what is what.
Mera yah eliminator meri mere se iske galat button dab gaye h minut Tak ke bad apne aap stopHo jaati hai please request hai aapse ki mujhe bataen ki kaise theek hogi
Hello Fellow colleagues. If you enjoy the video please click that like button and if you did not, dislike it and let us know in comments, what was, that made you not happy with the content, so I can learn from it and make better videos for you in the future. Have a great day everyone.
Is that okay to LINE to GROUND power supply ?? Thank you . New subscriber here.
can this drive be run on 0 - 3.3v? Eg. putting it in 0-5v mode using Al1 and com and somehow making the drive run at 100% when it reaches 3.3 and hold all the way to 5v?
Hola me prodrias guiar en lo siguiente, ese variador esta en una talanquera de peaje, en uno muestra falla E01, E02 en otro la E13 en otro el display parpadea en FCS, y no logro encontrar como una listado de fallas o errores
sir can i give dc supply from solar to vfd....then if i give dc supply to vfd ,how can i read dc voltage and current from vfd
Very grateful for this video. Just little slower & clearer would be great. Your European accent is a little hard to follow. Pretty sure I have set mine up properly however I had to watch it many times. So just a bit slower with less malarkey for the non electrical engineer like me. Thanks again.
Working on it, Thank you.
How do I remove opf2 on this inverter
Bang sdh saya setting HSP posisi 60 ..rpm tetap tdk naik ..mohon pencerahan nnya
Fantastic video. You mentioned that you are able to set a higher HZ in the vid. I have tried that but can not get my motor to spin up past 50 Hz. I want to go to 200 Hz. Do you have any clue to why not?. Best regards Thomas
HI There. There is 2 types of frequency in your drive. One is base frequency that can only be 50 or 60 and other is run hz. Change your max frequency to hat ever you need and you should be good to go, believe i mention in video what is what.
Tell me reverse forward parameters please
Mera yah eliminator meri mere se iske galat button dab gaye h minut Tak ke bad apne aap stopHo jaati hai please request hai aapse ki mujhe bataen ki kaise theek hogi
Thanks a lot.
Thanks that’s helpful
S/S switch to run