Not only is it nice but its of higher quality than can be bought almost anywhere. Soldered and heat shrunk connections completely covered in proper tape. Great work!
The glue on the Duck Tape will react with the silver backing and you will see discolouration/stains after a few months. There is however a special adhesive for mirrors that is stable and not cause the staining effect.
That was a back cover which the painted white is use to reflect and magnify the lights of the leds for more illumination. Sorry for I didn't merged the part of the video that shows the white cover.
@@gudvooy2 hala pinoy po pala kayo 😅 thank you po sa pag sagot sa comment ko, try ko po ulit mag hanap sa iba ng paint remover at etching cream, pag wla ako mahanap yan nalang ang gagamitin ko, ask ko lang po about dun sa touch button meron po kaya nyan sa shoppe? Pasensya na po sa kulit ko, gusto ko sanang e DIY yung nabili kong mirror para gawin kong vanity mirror sa make up po, Thank you po..
You can buy the power source of 12v DC or depending on the LED power supply required. You can buy the sensor switch in the description. Click the link.
This video is amazing.. I just following the steps, but you need to write more in deacription. That you need to do sanding after the paint removing step. Because after using paint remover, the silver layer didn't com out. So we need to do sanding. For more information by my experience (just did it today), i sanded it using 320 grit of sandpaper and water. And one more thing i found by experiment. It will be better if we using masking tape that made off plastic or other material that will not scratch when applying the paint remover. I meant it will be more better if it not a paper material masking tape. Overall this video really good. Thanks a lot. 🙏
Sanding is needed when you don't have the etching cream to make the glass blurry. You can do the sanding process without using paint remover. Yes you are right, if we use a much better tape and have a better adhesiveness. You might have more cleaned and sharper edges.
No. I mean, if you used a sand paper to scratch out the silver layer you don't need the etching cream to make the glass blurry because the sand paper does its job in Removing the Silver layer and making it blurry.
@@gudvooy2 no, i did sanding it. But it's not blurry.. It's clear.. Maybe it will getting blurry if i use a lower grit of sandpaper, without water when doing sanding.
@ Mogi Sanjaya thank you so much, I used the paint remover. But, then noticed there was still mirror under the grey layer. So, I went through comments and found your ty so grateful that you shared this.
Why did you tape it, what there a need? Also the white paint stuff, what is that, what did you put it on and why ... what is its purpose? Sorry hard to tell from video
Also do you think it would work if i used the led lights that come with a remote ? Could i still wire it to the touch sensor but use the remote to change the colors ?
I'm not sure if you can do it. It would require a good connection. Try this but take your own risk. I will not responsible for any injuries and damages for any misconnection will be made. You may connect first the the sensor switch from 12v supply then connect your led with remote to the output of the sensor switch. But remember that the output for the sensor which would be led but you can try the said procedure. Good luck.
Yes you can use paint remover. In the video it was actually a paint remover. Just a tip, use a sponge 🧽 (scotch brite)- rough side to remove the painted mercury. Because using a paint remover will take you hard to time to it.
Great video ... thanks so much Can you give a parts list or tell me the name and where i can purchase the light sensor? Also can this be done as a 120 volt system so it can be hardwired?
Went to the description like you suggested but it is not in english so im having trouble still. Im sorry. Can you provide a material list in english and where i can find these? Thank you for your response and help
Hi! love your video,You convince me to try but on a round mirror. I have a question, the cable you had between the touch switch and the "exit" of the frame (i don't have the vocabulary-sorry) are part of the packaging /order on aliexpress ? (for the touch switch) And what kind of cable did you use to connect the set with with a the extern plug? (hope i'm clear) Love what you do.
Armour etch. You can buy it in ebay or amzon. Here is the link: www.ebay.com/itm/Glass-Supplies-Armour-Etch-Glass-Etching-Cream-10-oz-NEW/383901572042?hash=item5962511bca:g:OpAAAOSwCdRe8OaZ
Lo único que quedo horrible fue las lineas donde aplicaste el removedor de pintura, si hubiese usado una cinta adhesiva de mejor calidad, te hubiese quedado bien definido el delineado translúcido.
For next video please show me how to make a ghost appear then disappear in the mirror. Maybe add speakers that can play scary noises? It's for kids room. :))
Does this sensor work without removing the mirrored surface? Can I just place it in the center at the bottom and touch that spot or do I need clear glass for it to work properly. Thanks for posting the video. The connections are all very clear.
ive never done it, im still researching about it before i do mine. but based on what i read - if u dont remove the mirrored surface - u wont get to enjoy the blue, red or white indicator colours. and the point to touch would be almost a secret that only u would know haah
@@drazmishah It actually doesn't work through the mirrored surface, it has to be a clear spot. My inquiry was because I got a mirror with LED lights around the perimeter, but the vendor hadn't put in a touch switch and I wanted to add one. My solution was to add the sensor in the clear track for the lights, at the bottom in the middle. I have a lit up rectangle in that spot. Not perfect, but it doesn't look bad, at least not as much as I would have thought.
Eching cream is use for glasses to make them blurry. You can find it to ebay or amazon. If it is not available, you can use sand paper to make the glass blurry.
No aliexpress fala: "The back light icon can be seen on the mirror after the touch switch is powered" Mas no seu video, quando está off o ICON LED está ON .. But in your video, when the led strip off, the ICON LED is ON .. 00:07 Problem with the touch switch ?
Oh this is amazing. You actually showed every step. Thanks
Exactly what DIYers need. Every step.
Not only is it nice but its of higher quality than can be bought almost anywhere. Soldered and heat shrunk connections completely covered in proper tape. Great work!
Now I understand how light and touch sensor build in Mirror 👍 thankyou ❤️❤️❤️
Yes, I'd like to order 3...oh, wait, make it myself?!...guess I'm stuck with ancient bathroom technology.
Beautifully done none the less...
Check this out too, you might be interested:
th-cam.com/video/2xYnyX8VMjU/w-d-xo.html
@@gudvooy2 checking it out. Very nice but I'm not that skilled
The glue on the Duck Tape will react with the silver backing and you will see discolouration/stains after a few months. There is however a special adhesive for mirrors that is stable and not cause the staining effect.
What do u call it
yeah bro. what do u call it?
@@drazmishah Mirror Adhesive.. Ask at your hardware shop. www.tilemerchant.ie/evo-stik-mirror-adhesive-290ml.html
@@redfire20003 fantastic. Im definitely getting it. Ive ordered the rest of the items online already. Its gonna be my lil' pet project
What is the name?
Superb video highly detailed and thanks for showing each and every step, I always wanted to the the etching and paint removal steps
Thank you.
Sir.
Exelent every thing Step by step.
Thank you.
Omitiste el proceso de lijado de la plata y el delimitando de las lineas para un acabado mas pro
Wow..keren
Saklar nya pakai apa ya boss
Can we use any paint remover?
Yes sure
Superb where can I get the paint remover
You can buy in a hardware store.
Que le hechaste para remover la pintura amigo ?
Quita pintura.
Any paint remover can be use?
Yes
Cairan pake apa om biar bis kupas belakang cermin
Super Bhai at 6:40 you paint white colour what is the use of this
That was a back cover which the painted white is use to reflect and magnify the lights of the leds for more illumination. Sorry for I didn't merged the part of the video that shows the white cover.
Bro kon kon camical use kia aapne
Can make it without Etching cream ?
You can use sand paper. But that would make the edge surface fuzzy instead of a sharp edges.
Hi, thanks for sharing with us. It is the same if we sandblast the mirrow ??
Maybe it's better.
Donde consigo el y como se llama el interruptor????? Y si me puedes decir el nombre de los materiales w ocupas 🙏. En español si!!!!
Esta todo en el descripción. Se llama "touch switch"
Como se llama el liquido que usas al principio para remover
Se llama decapante, quita pintura para metal madera.
I loved this mirror, from brazil
Te quedo mas que excelente .......Amigo una pregunta donde va el touch no se perfora el espejo?
No es necesario hacer perforación en el espejo donde esta el touch sensor switch.
no es necesario. el sensor alcanza a recibir señales a través del cristal
Do you connect leds with input or output of touch sensor?
No. Those leds were built in with the sensor switch.
Awesome can anyone please name products alternative, because i can't find them in my area
Como quitaste la plata del espejo?
Con estropajo con agua.
It is available in Philippines? The chemical that you used?
I think so.
@@gudvooy2 I try to find it but there is no available, do you have alternative solutions for this?
Pwede mo pong gamitan ng lacquer thinner. Maaari din po sandpaper nalang po.
@@gudvooy2 hala pinoy po pala kayo 😅 thank you po sa pag sagot sa comment ko, try ko po ulit mag hanap sa iba ng paint remover at etching cream, pag wla ako mahanap yan nalang ang gagamitin ko, ask ko lang po about dun sa touch button meron po kaya nyan sa shoppe? Pasensya na po sa kulit ko, gusto ko sanang e DIY yung nabili kong mirror para gawin kong vanity mirror sa make up po, Thank you po..
Seguro meron sa shoppe. Sa AliExpress ko kasi yon binili.
What kind of cable did you use to connected to other cable on 17:32 (the green one) where can i find it?
I think you are asking about the "heat shrink tube".
Heat shrink tube is use to cover the open shielded wire.
Thanks for vedio but I have question how do you make the circuit (power source and LED and switch touch )
You can buy the power source of 12v DC or depending on the LED power supply required. You can buy the sensor switch in the description. Click the link.
Nice. Why didn't you put the led facing outwards right into the clear area for more brightness?
Try it yourself with a flashlight facing infront of you face. You know what I mean.
agar yeh light khraab ho jaaye toh replace ho jayegi?
Can't understand
This the video I was looking for.. amazing work.. love from India 🇮🇳
This video is amazing.. I just following the steps, but you need to write more in deacription. That you need to do sanding after the paint removing step. Because after using paint remover, the silver layer didn't com out. So we need to do sanding.
For more information by my experience (just did it today), i sanded it using 320 grit of sandpaper and water.
And one more thing i found by experiment. It will be better if we using masking tape that made off plastic or other material that will not scratch when applying the paint remover. I meant it will be more better if it not a paper material masking tape.
Overall this video really good.
Thanks a lot. 🙏
Sanding is needed when you don't have the etching cream to make the glass blurry. You can do the sanding process without using paint remover.
Yes you are right, if we use a much better tape and have a better adhesiveness. You might have more cleaned and sharper edges.
@@gudvooy2 ahh.. I see.. So the etching cream also used for scratching that silver layer. Oh nice to know about that..
Thank you so much 🙏.
No. I mean, if you used a sand paper to scratch out the silver layer you don't need the etching cream to make the glass blurry because the sand paper does its job in Removing the Silver layer and making it blurry.
@@gudvooy2 no, i did sanding it. But it's not blurry.. It's clear.. Maybe it will getting blurry if i use a lower grit of sandpaper, without water when doing sanding.
@ Mogi Sanjaya thank you so much, I used the paint remover. But, then noticed there was still mirror under the grey layer. So, I went through comments and found your ty so grateful that you shared this.
Excellent work... please let me know the touch swich compny and where to buy....and price of it 🙏
The link to buy the touch switch is in the description.
I've a question after how much time i can remove itching cream
After 5-10min.
With what separated mercury from the glass?
Try to use sand paper. Use the smoother type.
The best you can use is the scotch brite sponge, use the rough side of the sponge.
excellent video.
nice video, its possible if the power source from battery?
Yes its possible to use 12v battery power supply.
I dont have bluring cream . what i i do ?
You can scrab it with sponge in the rough side of it. Even sand paper but be sure not to damage the edges.
@@gudvooy2 ok i try. Thanks bro
@@gudvooy2 what about ferric chloride pcb etching power can I use it
That's a good idea. You can try it
Why did you tape it, what there a need? Also the white paint stuff, what is that, what did you put it on and why ... what is its purpose? Sorry hard to tell from video
You must tape the wires. I painted the background of the frame.
Also do you think it would work if i used the led lights that come with a remote ? Could i still wire it to the touch sensor but use the remote to change the colors ?
I'm not sure if you can do it. It would require a good connection. Try this but take your own risk.
I will not responsible for any injuries and damages for any misconnection will be made.
You may connect first the the sensor switch from 12v supply then connect your led with remote to the output of the sensor switch. But remember that the output for the sensor which would be led but you can try the said procedure. Good luck.
Very very nice video
Bhai ye kha milega
Asking one questing, you painted a wooden sheet n placed mirror front face on it ... Please clear my doubt
The painted side of the wood must be inside. It serves as a cover and it reflect the light of the led.
Can we use any paint remover to clear the mirror back colour?
Please tell me.
Yes you can use paint remover. In the video it was actually a paint remover. Just a tip, use a sponge 🧽 (scotch brite)- rough side to remove the painted mercury. Because using a paint remover will take you hard to time to it.
Adopter kitna ampere hai
2 amps max.
i dont know where u are from. you look malaysian tho. this video of urs tho, is simply amazing.
I'm a filipino SIr
पेंट रिमूवर का लिंक दीजिए ऑन flip cart 😊
Great video ... thanks so much
Can you give a parts list or tell me the name and where i can purchase the light sensor? Also can this be done as a 120 volt system so it can be hardwired?
Where to buy the sensor is in the description. You can use a 120v adapter with an output of 12 volt DC.
Went to the description like you suggested but it is not in english so im having trouble still. Im sorry.
Can you provide a material list in english and where i can find these?
Thank you for your response and help
@@TheBartman55 A real DIYer would learn a language to get the parts list! Lol..its actually English on my list..maybe he changed it for you. Gd luck
Was that paint remover ?
Will try make on that's awesome
Yes it was.
@@gudvooy2 great work thanks for prompt response 👍 😀🙏
what is the product used for removing the coating??? I used a metal paint remover but its not working so smoothly
You need to repeat the process.
What is etching cream .. is this a medical product or something else?
Great video ty for sharing
Mas bisa beli tombol on of ny
Bless your damn heart for posting this !
Lovely. Thanks for sharing it. Which paint did you use in the last?
It was a normal paint for wood
@@gudvooy2 thank you very much.
@@sheen2923 assalamaulaikum
Genial amigo, una pregunta como se consigue la crema que le aplica despues de remover la pintura del vidrio?
plotteralia.es/grabado-de-cristal-crema-205.html
Bro I want this chemical m from Pakistan so how can you help me
You can buy in your local paint store.
In 2:13 may i know what paint or chemical is that?
Its a paint remover.
@@gudvooy2 all paint remover can also remove that back silver coating of the mirror?
@@magals8955 I think so. I just used a wood paint remover.
Absolutely yes.
Hey, what kind of tape you used for the lines? That won't react with paint stripper??
I just used a masking tape. You can even use a duck tape, it is more adhesives.
@@gudvooy2 ok. I did that and worked. But the paint stripper is not taken the mirror paint away. Just the gray paint.
What is white pasta you used?
It was a glass etching cream. Use to make the glass blurry.
Though not a high finishing professional job but for a DIY 10/10....
Nice mirror
The switch on the mirror doesn't look good. Can it be placed somewhere else to get the same effect?
Beautiful!
I'm buying paint remover gel plz 🙏help me
Go on!! Buy a paint remover
Rs....
Привет! Где купить это средство для снятия эмольгаммы? Где его купить этот декопантовый гель?
You can find the paint remover in the hardware store, paint store.
@@gudvooy2 а растворитель подойдёт?
I don't think will work.
@@gudvooy2 а что же там за дйствующее вещество.?за сщёт чего идёт реакция?
You done wonderful bro thank you for sharing your videos
Qual o nome do produto que remove a tinta do espelho??
Son gel de quita pintura.
kurang derek apa aja bahan yg di gunakan,,,harus di jelaskan,,
??
Sinkong itu sampeu😂
Sensor ki kimat kitni hai
I think more or less 5$
Hi! love your video,You convince me to try but on a round mirror. I have a question, the cable you had between the touch switch and the "exit" of the frame (i don't have the vocabulary-sorry) are part of the packaging /order on aliexpress ? (for the touch switch)
And what kind of cable did you use to connect the set with with a the extern plug? (hope i'm clear)
Love what you do.
You'll gonna need a 12 volt power supply, atleast 3 amps.
It was a 5.5mm female-male plug Dc wire connector.
Now I understand how it’s worked thanks
nice! want to learn this... 😊 new sub! here!
Your video is so amezing. Sir which chemical used for remove mirror back color
I just used a paint remover.
@@gudvooy2 sir can u suggest paint remover name please
@@gamewithphysics6070 I used DAXTON gel paint stripper.
Really nice video. 👌
Sangat membantu pak..
Terima kasih Pak
awesome man, thanks for sharing, ..instead of keeping to yourself , knowledge shared is knowledge earned..
Thanks
I do not understand why did he paint (white colour ) on a separate board and later put the mirror on that board ??
So that the light reflects inside the mirror and more luminosity can make.
Touch side pe mirror ko cut kiya ha kya
I don't understand your language sir.
@@gudvooy2 I am just asking to you that where the touch button ,you cut the mirror that side
@@technicalandinformativevid7128 I did't made any cut to the mirror nor I made any hole to it.
@@gudvooy2 to touch sensor mirror ke back side pe laga ha aur front se mirror touch krne pe work krta ha
Congratulations!!! Your video is very good. Another point is that I can not read your language. Where are you from? I am from Brazil. Regards.
Great work...👍
You might be interested with this too, no touch switch:
th-cam.com/video/2xYnyX8VMjU/w-d-xo.html
Name of eching cream????
Armour etch. You can buy it in ebay or amzon. Here is the link:
www.ebay.com/itm/Glass-Supplies-Armour-Etch-Glass-Etching-Cream-10-oz-NEW/383901572042?hash=item5962511bca:g:OpAAAOSwCdRe8OaZ
Can you link all of the materials used ? Im very interested in making my own
The link of the sensor is in the description. The rest was bought to AliExpress
How so I remove the blurry part I don’t want blurry any químico tha I can use to cleaning the blurry part please
If you want to do the project, you don't need to follow what I did to make the mirror blurry.
Good idea 👍
What is armour etch??
Its an itching cream use for blurring the glass. To make the glass from transparent to blured. So you wont see what's inside the glass.
Lo único que quedo horrible fue las lineas donde aplicaste el removedor de pintura, si hubiese usado una cinta adhesiva de mejor calidad, te hubiese quedado bien definido el delineado translúcido.
For next video please show me how to make a ghost appear then disappear in the mirror. Maybe add speakers that can play scary noises? It's for kids room. :))
This might help you.
th-cam.com/video/BsciTxZtwWs/w-d-xo.html
Wow.genius ka talaga kabsat
ayaw ko kasi makalimot sa electronics kabsat.
tnx master, tagal ko na naghahanap ng ganitong video. pinoy din pala makakapagturo saken
Jar aapse baat karni hai
Does this sensor work without removing the mirrored surface? Can I just place it in the center at the bottom and touch that spot or do I need clear glass for it to work properly.
Thanks for posting the video. The connections are all very clear.
Yes it can be work without removing the mirrored surface.
ive never done it, im still researching about it before i do mine. but based on what i read - if u dont remove the mirrored surface - u wont get to enjoy the blue, red or white indicator colours. and the point to touch would be almost a secret that only u would know haah
@@drazmishah It actually doesn't work through the mirrored surface, it has to be a clear spot. My inquiry was because I got a mirror with LED lights around the perimeter, but the vendor hadn't put in a touch switch and I wanted to add one. My solution was to add the sensor in the clear track for the lights, at the bottom in the middle. I have a lit up rectangle in that spot. Not perfect, but it doesn't look bad, at least not as much as I would have thought.
@@alvo-oooo test it. should be easy to test. Or, did you?
@@bellesreceptionists3952 Yes, I was able to test it. Through the silvered part, nothing. Behind a section sandblaster ckear, it works perfectly.
idol, wala ka bang marerekomenda na local na paint remover?
Try mo lacquer thinner.
sige try ko pero umorder na ako gel type spray ni bosny sana epektib pareho
సూపర్ 👌👌👌👌💐💐💐💐💐
Eching cream lagane se pahle kya lagaya sir ji... Wo to dikhaya nahi.. 3.35 min me..??
Eching cream is use for glasses to make them blurry. You can find it to ebay or amazon. If it is not available, you can use sand paper to make the glass blurry.
idol, saan nabibili ang touch screen sensor?
Nasa description po sir. Sa Aliexpress po marami po doon.
@@gudvooy2 Lazada din.
Iyon yung pangcover sa likod. Pininturahan ko yun para maging reflective ang lights sa loob at mas luminous sya.
मुझे ये पेंट रिमूवर चाहिए
Very nice
No aliexpress fala: "The back light icon can be seen on the mirror after the touch switch is powered"
Mas no seu video, quando está off o ICON LED está ON ..
But in your video, when the led strip off, the ICON LED is ON .. 00:07
Problem with the touch switch ?
Thank you so much!
You're welcome
Biar standby hidup terus gmn ya bang
Can't understand
@@gudvooy2 I had one like it, but the light changed quickly and instantly dimmed
The switch has a 3 selection of dimmer. You can change yours, buy it on the description.
Nice job brutha
Appreciate it