Good video, got a 760 36" for free that had an error message. Fixed it in 15 minutes, thanks to this and another video. Instant 5000 dollar come up. Thanks.
JUSTO VOY A IMPRIMIR EL ULTIMO TRABAJO URGENTE, EN SEMANA SANTA (VACACIONES), Y ME ENTERO QUE EL TANQUE DE RESIDUO ESTA LLENO....!!!! CASI ME DA UN INFARTO......por suerte encontré tu video y me ha servido mucho.... GRACIAS, INFINITAS GRACIAS...!!!
Thank you Joao. The ipf780 enters differently in Service Mode: 1) Turn off the printer power.2) Turn on the power while pressing the [Load] key and [Navigate] key.* Keep pressing the above keys until "Initializing" is displayed.3) "S" appears at the top right of the display. Follow Joao's instructions
Muchas gracias, seguí los pasos y me funcionó. Para los que tienen dudas yo lavé las esponjas del cartucho de mantenimiento hasta eliminar toda la tinta, lo puse en la misma posición y está funcionando de maravilla 😁
@@anaonofre8127 presionas ambos botones y luego boton power de encender una vez q desaparezca el logo de canon ahi recien sueltas y listo ami me funciono
Sabe qual o motivo do sistema colocar como o tank cheio, e ele estar vazio? Estou tento que reiniciar o meu seguidamente com essa sua dica (muito valiosa, obrigado!).
Thank you for the video. Can you tell when the tank is actually full after a reset? Does the machine tell you or do you need to inspect? Also, how many times can you reset before it needs to be replaced... or can it be emptied and reused again? Many thanks.
The only way to tell if the maintenance tank is full after this is inspecting it or when you see ink dropping from the printer 😅. I already did it 5 times when it gets to 40% and still have a lot of room left.
love this video are u able to tell me how to reset the SP1 which is the ink tube unit. Id like to get this reset since the tubes are in perfect condition and the printer isnt worth the cost to replace them so id like to just run the printer until an issue happens since i do have a new printer to replace my current printer once there are issues.
Hello! Do you maybe know how can I change the print margins for the cut paper feed? I have to set all the margins to 3 mm instead of having a 23mm right margin. Thank you!
1. As I read in your comments this procedure is when you want to empty your tank and of course you don't have a new one. As a new user, the maintenace tank is reusable? Can I empty it and use it again? According to you I can use the same tank forever . Probably this is for one time if you don't have a new tank
o meu azul nao ta mandando tinta pra cabeça. Tem ar nas mangueiras, mas talvez seja o cartucho ruim. Gostaria de primeiro ter certeza que nao é ar na mangueira.
Great video, thank you!. It works great. I did reset without removing M-tank. Coud you tell me how can I check if the M-tank is full? If I remove the m-tank before reseting, will I be able to plug in the same m--tank and then, reset it? I am a little bit worried that printer will not allow me to plug the same cartridge. Please advice.
peace be upone you. ineed your advice .ihave canon IPF765 machine that has not been in operationn for nearly two years .ido not know if the one who sold me ajob has apre-stop cleaning and i want to run and what are the steps to restart it
Eu sempre faço reset na minha quando chega em 40% para não correr o risco de esquecer, já fiz 5 vezes e ainda tem espaço de sobra pra pelo menos mais umas 4 vezes, já tenho a impressora há 4 anos e nunca troquei o cartucho.
hello, I have the same problem with my CANON IPF 8000S, how i can make it working again before i removed the tank with the caouchou and make them dry and re-enter again now it becoming again , kindly advise me
Olá João. Ao Entrar no modo de manutenção, exibe o "S" no canto superior como o vídeo, não some a mensagem de troca do cartucho de manutenção. Não consigo entrar no Menu pra fazer o reset do cartucho. Saberia uma solução?
Hi, my printer model is different, how can I reset waste ink for canon image prograf 5100 printer please. It will be highly appreciated if you could please bail me out. Thanks.
Hi, do you know if i can remove my ink cartridges with the printer turned off, im going to refill and would like to check how much ink is remaining occasionally as the ink monitoring will be turned off. Thanks
But there is no need to check the ink level. Even if the monitoring is off the printer still detects a low ink level and warns you to insert a new one.
Saludos amigo por que me sakle desactivado el boton print en los archivos pdf unos si envia a imprimir otros no cual es el problema, para enviar a imprimir siempre se debe hacer este proceso de los 2 botones gracias !
Hello!, i have printing problems with this plotter, when the plotter is printing, suddenly starts to stain the paper, sometimes it does at the beggining and sometimes in the middle of the work, and sometimes works perfectly, what could it be?
pelo que percebi no vídeo, vc está usando tinta paralela, já usei nas minhas ipf770 e tive que colocar chip pra ploter reconhecer como se fossem originais. não teve que fazer isso?
Não tive de fazer isso não. Quando a máquina acusou o fim do cartucho inicial eu só enchi ele com tinta Inktec e quando coloquei de volta na máquina ela me perguntou se eu queria continuar imprimindo com aquele cartucho, deu um monte de avisos inclusive que posso perder a garantia, mas no final desativou os níveis de tinta e me deixou continuar imprimindo. Desde então já enchi eles umas 3 vezes cada e nunca mexi no chip. Na época até gravei um vídeo mostrando, vou ver se coloco aqui no canal.
eu faço exatamente assim, trabalho co. as iPF tem 9 anos. tenho as 770 a apenas 7 meses, e nas duas com um certo tempo começam a aparecer a mensagem que está recarregando as tintas dos cartuchos e várias vezes não para essa msg, somente ao add tinta original ou os cartuchos que recarrego e coloco os chips que compro na China. se puder add meu zap . 34992604256. abraço!
Essa mensagem só aparece quando acaba o cartucho. Eu fiz isso só 1 vez e nunca mais apareceu... Não sei como fazer na sua então, talvez seja uma atualização de software que a canon fez. A mensagem que aparece é exatamente a mesma do vídeo?
Hola, tengo un problema, a ver si me puedes ayudar por favor, tengo un plotter IPF 770, y cuando me coloco a imprimir, se coloca a imprimir y no para hasta que se me acaba el rollo.
So, if i understand correctly, you reset the maintenance tank from the service mode of the printer and you will never have to buy a new tank? Or it's something i am missing??
Yes, i will have to change it with a new one when it gets physically full, understood. But do you think i can do 2-3 resets before i buy a new one? So i dont need to buy a meaintenance tank chip resetter, right??
Boa tarde, o meu cartucho está com 20% só, não encontro outro para comprar, se eu resetar e continuar usando esse da certo? Ou eu teria que fazer uma limpeza?
My iPF-785 Has an error 03800500-2F47 I can not fix the problem. Do you have any idea what will be the problem?.. already changed the MC-10 maintenance cartridge and the print head, but no luck... Any suggestion will be appreciate. Thanks
hola, tengo un problema con ploter Canon IPF-750, me marca error E161-403E, Y NO ME DEJA IMPRIMIR. me podrias comentar que problema es, como lo puedo eliminar. gracias.
It holds all the ink that is used in the cleaning process and when it is full or 0% you need to change it. But it has no sensor to tell you that it is full, so they program it to say that it is 0% when actually it is not. So we reset it until it is actually full.
@@jpfernandes Hi, I have a problem lately with my printer, when I feed the manual print, it loaded and take times analyzing then becomes idle and slowly push out the paper and cancelled the printing, same thing when I try to print a nozzle check and feed manually but nothing was printed out till the paper slowly load out and cancelled the print job.
Boa noite Você é de onde? Ganhei uma ipf755 parada a muito tempo de um amigo topógrafo e queria coloca-la para funcionar novamente. Está dando erro 03130031-2f26. Pode me ajudar?
Anyone work out how to reset the tank on the tm-300. Had printer less than a year and need to replace already. I can get into service mode ok. But lost after that.
@@aruize78 No amigo solo presione los dos botones que muestra luego vas a mantenimiento, si es que te salen lineas alrrededor del un texto o de un grafico , y se activan las tintas otra cosa mas facil para poner el papel lo presionan hacia abajo para que agarre rapido el canon ipf 670
Amigo, tengo un plotter canon ipf670, ya resetie el cartucho de mantenimiento porque se llenó, lo he lavado y vuelto a montar, me pidió cambio de cabezal de impresión, ya lo cambie, ahora que le cambié el cabezal me tira un error 03130031-2F72, sabes cómo solucionarlo? Gracias
![เปิดบ้าน โคตรสวย ป๋องกพล รู้จักตั้งนาน เพิ่งรู้ว่ารวย!!! l [Nickynachat]](http://i.ytimg.com/vi/tmgCF_2HfYI/mqdefault.jpg)
Good video, got a 760 36" for free that had an error message. Fixed it in 15 minutes, thanks to this and another video. Instant 5000 dollar come up. Thanks.
JUSTO VOY A IMPRIMIR EL ULTIMO TRABAJO URGENTE, EN SEMANA SANTA (VACACIONES), Y ME ENTERO QUE EL TANQUE DE RESIDUO ESTA LLENO....!!!! CASI ME DA UN INFARTO......por suerte encontré tu video y me ha servido mucho.... GRACIAS, INFINITAS GRACIAS...!!!
Thank you Joao. The ipf780 enters differently in Service Mode: 1) Turn off the printer power.2) Turn on the power while pressing the [Load] key and [Navigate] key.* Keep pressing the above keys until "Initializing" is displayed.3) "S" appears at the top right of the display. Follow Joao's instructions
you literally just saved my business. thank you soo much...
Muchas gracias, seguí los pasos y me funcionó.
Para los que tienen dudas yo lavé las esponjas del cartucho de mantenimiento hasta eliminar toda la tinta, lo puse en la misma posición y está funcionando de maravilla 😁
Si al presionar los botones de load+naviget no enciende q puedo hacer?
@@anaonofre8127 presionas ambos botones y luego boton power de encender una vez q desaparezca el logo de canon ahi recien sueltas y listo ami me funciono
puedes decirme con q lo lavaste xfa, gracias
Eso haré a ver si lo hago bien, xq están muy caros para cambiarlo
con que lo lavaste?
Thank you so much! This info saved me a $250 Service Fee!!!!
Thanks so much - had to print one more poster and don't have time to wait for the Maintenance Cartridge to come in!
Após o procedimento que informou resolveu o problema do tanque, mas agora fica aparecendo que precisa trocar cabeça de impressão, consegue ajudar?
hi thank you very much
Does this procedure also work with Ipf710?
Sabe qual o motivo do sistema colocar como o tank cheio, e ele estar vazio? Estou tento que reiniciar o meu seguidamente com essa sua dica (muito valiosa, obrigado!).
Before your maintenance tank "fills", not empties right?
Thank you for the video. Can you tell when the tank is actually full after a reset? Does the machine tell you or do you need to inspect? Also, how many times can you reset before it needs to be replaced... or can it be emptied and reused again? Many thanks.
The only way to tell if the maintenance tank is full after this is inspecting it or when you see ink dropping from the printer 😅. I already did it 5 times when it gets to 40% and still have a lot of room left.
love this video are u able to tell me how to reset the SP1 which is the ink tube unit. Id like to get this reset since the tubes are in perfect condition and the printer isnt worth the cost to replace them so id like to just run the printer until an issue happens since i do have a new printer to replace my current printer once there are issues.
Hello! Do you maybe know how can I change the print margins for the cut paper feed? I have to set all the margins to 3 mm instead of having a 23mm right margin. Thank you!
Thank you so much for that! For iPF610, press Feeder Selection & Info buttons, then Power.
1. As I read in your comments this procedure is when you want to empty your tank and of course you don't have a new one. As a new user, the maintenace tank is reusable? Can I empty it and use it again? According to you I can use the same tank forever . Probably this is for one time if you don't have a new tank
I'm using the same tank for 4 years.
Hello can you tell me how i can RESET Maintenance Tank plotter Canon TM 300 THX
pudiste hacerlo? para la tm200? please
João Paulo vc poderia gravar um reset para cartucho de manutenção Canon ipf 605
João, teus videos tem me salvado, muito obrigado! Pergunta: Como faz pra tirar o ar das mangueiras? Obrigado!
o meu azul nao ta mandando tinta pra cabeça. Tem ar nas mangueiras, mas talvez seja o cartucho ruim. Gostaria de primeiro ter certeza que nao é ar na mangueira.
Obrigado. Mas nunca tive esse problema de ar nas mangueiras.
@@jpfernandes era problema no cartucho, entupido, entao nao mandava tinta (nao era ar na mangueira).
Obrigado!
Man you are a hero.. that fixed my IPF770 just when i really needed it to work!! Thanks so much
how to reset the Maintenance Tank for the Canon printer canon imageprograf tm-200 ???
Hello if you have a solution for your plotter can you tell me ? Thx
@@megatirage7747 porfavor como pudieron resetear cartucho de mantenimiento para la tm200?
Sir can you do a video how to stop ink detection to refill the cartridge
And how about inkowl do you advice
is it possible remove waste toner and re-use maintenance tank, if it is full?
is there any option to clean the printer or calibrate or clean headprint?
Great video, thank you!. It works great. I did reset without removing M-tank. Coud you tell me how can I check if the M-tank is full? If I remove the m-tank before reseting, will I be able to plug in the same m--tank and then, reset it? I am a little bit worried that printer will not allow me to plug the same cartridge. Please advice.
OK, no need to reply. It is possible to remove M-tank to check if it's full and then plug it in again. Thanks againf for posting this video!
peace be upone you.
ineed your advice .ihave canon IPF765 machine that has not been in operationn for nearly two years .ido not know if the one
who sold me ajob has apre-stop cleaning and i want to run and what are the steps to restart it
i have the 770 and it keeps saying refilling ik tanks will this fix that?
Olá João, quantos reset é possível em um cartucho de manutenção da IPF 770?
Eu sempre faço reset na minha quando chega em 40% para não correr o risco de esquecer, já fiz 5 vezes e ainda tem espaço de sobra pra pelo menos mais umas 4 vezes, já tenho a impressora há 4 anos e nunca troquei o cartucho.
@@jpfernandes ola, tem como fazer na canon TA-20?
What kind of paper i need to use to print on t shirt with this machine or wiyh ipf770
can i refill the ink cartridge and is it safe or not for the plotter
Can you clean out the maintenance tank itself?
It work with you ?
Amigo , sabe me dizer como fazer isso na IPF 710?obrigado.
Amigo, aonde você compra tinta inktec? Não acho de jeito nenhum
My ipf605 displays E196-404E and trying to enter service mode it says cover opened.
What should I do?
And how can I change the maintenance tank? Do you have a vídeo of that? Thank you!
No, but just remove the old and insert the new one.
WOW THANK you so much this now works GREAT !! good job sharing
Hi, i have IPF605 with red light of message and i dont know how to go in Service Mode to change the printer's head. Can u help me ?
when the "suction low message comes on.......what does that mean? Is that why the printer does not recognize the roll paper?
hello, I have the same problem with my CANON IPF 8000S, how i can make it working again before i removed the tank with the caouchou and make them dry and re-enter again now it becoming again , kindly advise me
Olá João. Ao Entrar no modo de manutenção, exibe o "S" no canto superior como o vídeo, não some a mensagem de troca do cartucho de manutenção. Não consigo entrar no Menu pra fazer o reset do cartucho. Saberia uma solução?
Thanks! Worked great on my iPF6300!
Canon 6410se can use this fungtion yes or not.
Hi, my printer model is different, how can I reset waste ink for canon image prograf 5100 printer please. It will be highly appreciated if you could please bail me out. Thanks.
Hello, i have canon iPF671 PRINTER, it show printhead error. How can I solve it?
hello i have probleme with oce cs2236 it's changed to offline and show message about orange line. I need help. thanks
Hi, do you know if i can remove my ink cartridges with the printer turned off, im going to refill and would like to check how much ink is remaining occasionally as the ink monitoring will be turned off. Thanks
It's fine to do that. I always do.
But there is no need to check the ink level. Even if the monitoring is off the printer still detects a low ink level and warns you to insert a new one.
@@jpfernandes how can i turn off the ink detection ?
And reset the maintenance cartridge can be done always ? There is no limit !
i want to disable the ink level detection from the service menu? how can i do that? it's really complicated
Can u plz tell how to reset maintenance nox of canon pro 521
fiz o procedimento, e após reiniciar deu erro no cabeçote, como resolver? existe algum reset de cabeçote?
Saludos amigo por que me sakle desactivado el boton print en los archivos pdf unos si envia a imprimir otros no cual es el problema, para enviar a imprimir siempre se debe hacer este proceso de los 2 botones gracias !
HELLO MY CANON IPF670E YOU HAD PAPER JAM BUT NOW YOU DO NOT HAVE ANYTHING ALREADY BORROW THE ERROR?
Hello!, i have printing problems with this plotter, when the plotter is printing, suddenly starts to stain the paper, sometimes it does at the beggining and sometimes in the middle of the work, and sometimes works perfectly, what could it be?
pelo que percebi no vídeo, vc está usando tinta paralela, já usei nas minhas ipf770 e tive que colocar chip pra ploter reconhecer como se fossem originais. não teve que fazer isso?
Não tive de fazer isso não. Quando a máquina acusou o fim do cartucho inicial eu só enchi ele com tinta Inktec e quando coloquei de volta na máquina ela me perguntou se eu queria continuar imprimindo com aquele cartucho, deu um monte de avisos inclusive que posso perder a garantia, mas no final desativou os níveis de tinta e me deixou continuar imprimindo. Desde então já enchi eles umas 3 vezes cada e nunca mexi no chip. Na época até gravei um vídeo mostrando, vou ver se coloco aqui no canal.
eu faço exatamente assim, trabalho co. as iPF tem 9 anos. tenho as 770 a apenas 7 meses, e nas duas com um certo tempo começam a aparecer a mensagem que está recarregando as tintas dos cartuchos e várias vezes não para essa msg, somente ao add tinta original ou os cartuchos que recarrego e coloco os chips que compro na China. se puder add meu zap . 34992604256. abraço!
Essa mensagem só aparece quando acaba o cartucho. Eu fiz isso só 1 vez e nunca mais apareceu... Não sei como fazer na sua então, talvez seja uma atualização de software que a canon fez. A mensagem que aparece é exatamente a mesma do vídeo?
sim. depois que vi que a sua é a 670, as novas não funcionam mais sem colocar chip.
Amigo, onde comprou suas tintas? também tenho uma IPF 770, mas não acho em lugar nenhum. Obrigado!
Hola, tengo un problema, a ver si me puedes ayudar por favor, tengo un plotter IPF 770, y cuando me coloco a imprimir, se coloca a imprimir y no para hasta que se me acaba el rollo.
Boa tarde
Esse reset tambem funciona para o erro 03800500-2F47 ..????
amigo una consulta como solucionaste ese problema erro 03800500-2F47
So, if i understand correctly, you reset the maintenance tank from the service mode of the printer and you will never have to buy a new tank? Or it's something i am missing??
+Theo You will have to change it when it gets full. But you reset it sometimes before because the printer says it is full when its actually not.
Yes, i will have to change it with a new one when it gets physically full, understood. But do you think i can do 2-3 resets before i buy a new one? So i dont need to buy a meaintenance tank chip resetter, right??
Works exactly the same way to ipf6400SE, thank you!!!!
hey how do i do this on imagePROGRAF 4000
any ideas on how ro fix error code 161-403E sady lozada
Hey man, Ipf605 work?
João Paulo fernandes. Através desse menu é possível fazer o reset do nível de tinta dos tinteiros ?
Não tem como.
Boa tarde, o meu cartucho está com 20% só, não encontro outro para comprar, se eu resetar e continuar usando esse da certo? Ou eu teria que fazer uma limpeza?
Tira ele e dá uma olhada, se estiver muito cheio tenta dar uma limpada.
Boa noite , posso mudar a tinta mbk do plotter ipf770 por corante?
When is the best time to reset it please is it best to do it is it best before 100%
My iPF-785 Has an error 03800500-2F47 I can not fix the problem. Do you have any idea what will be the problem?.. already changed the MC-10 maintenance cartridge and the print head, but no luck... Any suggestion will be appreciate. Thanks
www.manualslib.com/manual/790676/Canon-Ipf9000s.html?page=62
Very Useful. Use this tip for the second time after a cleaning of the maintenance tank. Thank you very much.
can we clean the tank?
Hey amigo, thanks a lot for this video. This rescued my day.
Hola!!! Necesito ayuda se come toda la tinta y dice q esta vacio y asi cuelvo y lleno y vuelve y dice lo mismo
hola, tengo un problema con ploter Canon IPF-750, me marca error E161-403E, Y NO ME DEJA IMPRIMIR. me podrias comentar que problema es, como lo puedo eliminar. gracias.
printcopy.info/index.php?mod=erc&brand=Canon&model=iPF510&code=E161-403E
hi
i have error 2f26 on my printer canon ipf 750 please how can i fixit thank you
what is the benefit of maintenance tank
Hi, May I know what is the purpose of maintenance tank? why it has to be 100%?
It holds all the ink that is used in the cleaning process and when it is full or 0% you need to change it.
But it has no sensor to tell you that it is full, so they program it to say that it is 0% when actually it is not. So we reset it until it is actually full.
@@jpfernandes Hi, I have a problem lately with my printer, when I feed the manual print, it loaded and take times analyzing then becomes idle and slowly push out the paper and cancelled the printing, same thing when I try to print a nozzle check and feed manually but nothing was printed out till the paper slowly load out and cancelled the print job.
Not sure, but maybe you're feeding it wrong or misaligned.
@@jpfernandes wait for 100% before resetting or before to reach 100%?
hello you know if it works for ipf510
Boa noite
Você é de onde?
Ganhei uma ipf755 parada a muito tempo de um amigo topógrafo e queria coloca-la para funcionar novamente.
Está dando erro 03130031-2f26.
Pode me ajudar?
É algum problema no carrinho. Procura no google pelo arquivo "Troubleshooting-Guide-E.pdf", que tem um guia em inglês sobre esse erro.
E a nova TM200 tem como desativar o nível de tinta?
hola, como reseteas el cartucho de mantenimiento en la tm200?
Can i do this when my plotter says 'maintenance cart replacement due' ?
There is no harm if you try.
OLA BOM DIA. ELA IMPRIMI EM VINIL?
how to reset maintenance cartridge counter in tm 5200 canon largesize printer
Good Job...How about print head reset?
now my plotter is working thnk god & u also
thankyou friend , really help me to much
Anyone work out how to reset the tank on the tm-300. Had printer less than a year and need to replace already. I can get into service mode ok. But lost after that.
como entraste a la tm300? yo tengo tm200, deseo saber como entrar a modo servicio para resetear cartucho de mantenimimento.
does it work on IPF 750????
yes it does.
Works great for my Canon iPF750. Obrigado amigo! :-)
Saludos amigOS funciona con los pasos del video pero activando mantenimiento de lo contrario no funciona asi lo intente YO
una pregunta.... lograste limpiar el tanke de mantenimiento?
@@aruize78 No amigo solo presione los dos botones que muestra luego vas a mantenimiento, si es que te salen lineas alrrededor del un texto o de un grafico , y se activan las tintas otra cosa mas facil para poner el papel lo presionan hacia abajo para que agarre rapido el canon ipf 670
hi, can we clean the maintenance tank?
Yes, but it's quite difficult.
Hi
Can you help me on error 2f1f on plotter ipf 765 please
Wow...it work for my IPF771, thanks man.
Como Reseta o Erro da Plotter IPF 770 e141-4046?
Amigo, tengo un plotter canon ipf670, ya resetie el cartucho de mantenimiento porque se llenó, lo he lavado y vuelto a montar, me pidió cambio de cabezal de impresión, ya lo cambie, ahora que le cambié el cabezal me tira un error 03130031-2F72, sabes cómo solucionarlo? Gracias
Disculpa lograste encontrar una solución al cabezal de tu Plotter?
Igual me sale cambio. De cabezal.. en este caso creo q ya fue la plother
THANK YOU SO MUCH! worked with my ipf6410se
sir how to reset printer head ipf671
Muito obrigado, funcionou perfeitamente este procedimento.
Thanks a lot for the information sir.
I have a problem with my ipf 771. Hardware error 03130031-2F72. Please help me fix it. Thank you!!
help !!! I have a canon ipf750 error 2F47
You can only help thank you ! You can fix it help
Thanks man, that just worked perfectly
Wow...it work for my ipf8410s, thanks man.
It worked on my 8400. Thank you.
i get the hardware error 03800500-2F47... any ideas?