Okay, I found something that absolutely one-hundred-percent fixed my Error 7 issues. After checking all of the sensors and making sure that there was nothing obvious wrong with my Shark IQ, I simply deleted the current map. It was behaving as if it was sitting on a cliff or a drop when it was several feet from one and I wondered if it had become confused and the map was corrupted. After deleting the map I told it to start all over from scratch and it has been working like a charm. Just like brand new. It worked for me so if you don't have any bad sensors or anything else physically wrong with your vacuum, give it a try. You might be as fortunate as I was.
Mine keeps saying too close to a cliff please reposition I am I even resetted it and I cleaned it all and it keeps saying it 😭 I don't even know what to do??
You can probably use any personal security cameras you have in your home that uses night vision mode. I was even able to see the IR with my doorbell camera.
I tested my cliff sensors with a multimeter before I bought replacements and I’m glad I did because the multimeter confirmed the leds for both the transmit and receive were both good regardless of the light test with the camera. The board does have a small black spot on the connector so I’m guessing the board has a burned pin I’ll have to find a way to test the board before buying anything.
Great videos! But I haven't been able to find the model I have - a UR1105ARUS. On mine, the vacuum motor went out - so I purchased a replacement and went to work R&Ring it.... When I removed the top cover, a small PC board (marked 'Dust Cup Hall (or Holl) PCBA) came loss and fell out of its place. Markings in it include the following: E486784, K01-RV-02-05, 0080749. I didn't see where it came from or where it goes back. I completed the repair or the vacuum, except placing that PC board in its rightful place, and it all functions - except that it now has a hard time docking and although the tower does it job, I get an error on my phone "I am unable to empty debris into the dock dust bin. Please empty my dock dust bin and remove blockages.". Do you have any idea where that PC board fits back in place? Thanks in advance!!
Can u please help me. Mine would charge and everything is good but when I hit to work , it stops and it wants me to clean it but it’s already clean ? Can you tell if it’s a sensor? Please advise. Thank you .
shark rv1001ae need to know what next replaced motherboard, two left side sensors and dust bin sensor says ready to clean and does nothing what is next to try
Hey great videos. I have a front left cloff sensor that either looks cracked or something inside. Do you have a video on how to replace it. I called shark and they said they do not sell that part. Thanks
Hi Smitty, is there a way to disable this sensors? I have this error again and again and I don't have stairs or something like that, the robot is just on circles, also getting erro with the boudary strip.
Good morning, when my robot shark starts up it says it has problems with the sensors and it doesn't seem to walk in the app it tells me to place it on a flat surface, how can I get it repaired?
Is there a fix to move the robot to a level surface, error #10? I have moved this thing to a level surface and it is not working any ideas would be great help for me thank you
Is there a way to bypass the cliff sensor? If so, can you show us how? After an hour on customer service with shark, I’ve learned my shark is a brick because of error 7 and there are no replacement sensors. The machine can function just fine if I can get the cliff sensor figured out.
I bought it and brought it to another country, when I got here as soon as I called it, it presented error number 7 even before mapping, can you help me?
my shark IQ got into dog poo, cleaned everything down to the frame, unit was completely a part. now I get the error #7. I think the sensors are specific and I could have put them in the wrong location. How can I tell which sensor goes where?
I successfully replaced the cliff sensors in my shark vacuum but now it can't find the dock. It tries to go in front firstr instead of backwards. What did i do that could cause this?
So when taking out one of the wheels from my unit, one of the wired connectors got damaged. I cannot for the life of me find a replacement anywhere. Any ideas on where I might get one? I'd hate to have to purchase a new $300 vacuum to replace what is probably a $5 part.
This makes perfect sense. I've used my phone's camera to test infrared emitters for all sorts of things. I'm using a pixel 7 Pro and the camera on that thing is phenomenal so I was able to check for the sensor lights in a fully lit kitchen LOL. Here's my situation that I'm not clear on. Each one of these sensors appears to have two lens pieces both at oblique angles to each other, but there is only one emitter light visible in each one. Does that mean that all the sensors are bad or all of them are good even though I only see one light in each lens set? I did not see any blue lights at all. Thanks!
There are two sensors, one is the infrared that emits the light and the other is like a camera that measures the distance of the light. I have error code 7 problem sometimes, I cleaned, check did everything and the infrared light are working but I don't know how to diagnose the camera. How do I know wish work and wish is my problem.
Trying to fix my friend's shark IQ.... evidently his ex let her ankle biter dog use the house like it's personal toilet... The shark did it's job over the mess. You get the picture. Have painstaking disassembled and cleaned the whole assembly but am getting an error code 7. Any ideas on how to move forward?
Animal pee is terrible for the electronics sensors are toast probably best to throw it away to be honest if less then a year old clean it up call customer service tell them it doesn’t work see if they will warranty it.
I have a Shark AI 2520 and it got the cliff sensor error and resting it didn't work. I of course did the sensible thing and bought new ones. I've replaced all the sensors, but I didn't reattached the wheel cables to the motherboard and now I have no idea which ports they go into. There's only one open port and it's too small for the wheel cable. HAAAAAAALPP
How do I find someone who works on these robots. I have a brand new one never used and it wont move the clean button and dock button blinks red and green back and forth. None of the vacumn places in my location works on them. And info would be greatly appreciated
My dog pooped and the shark ran it over. I tried to clean it the best i could but now it says error number 7. Could it be that the battery got wet while i was cleaning it? Should i change the battery? Please help
@@SmittysWorld any idea on what could cause this: vacuum can't find dock and seem to get stuck running into wall over and over again. Replaced motherboard but still does the same thing.
@@heatherduperly9869 hmm interesting does your front bumper love freely , did you replace the bump sensors and everything with the motherboard. How did the wheel circuits look
Do you know what the dark colored lights do? They almost look purple. They are part of the motherboard and also the side sensors. What about the silver looking sensors? One has a black and yellow wire that leads to the motherboard.
we just bought it and opened the robot today and it mapped the house fine. i wanted to map it again just to make sure it got it correct and now it keeps saying error 7 and to clean the sensors
mine is doing same thing but only on my area rug. it's got big rectangles on it outlined in black with different colors inside, keeps reading the black lines are a cliff and does the whole I side of square no problem til it does it 5 times and then it's done and says the error
Smitty, I'd love to talk to you about my IQ, everything works but it won't charge the battery. I put a new battery in still won't charge. It's like it doesn't know it's on the base. I know the base is good other one works fine.
do you have it backwards? I had an older one that went on charger with the buttons toward the base. the new one I just got has the charger things on the other side. when I first set mine up to let it charge before I used it. came back later and realized I put it backwards so had to wait til next day
I tried the phone trick and saw sensor lighters in all of the front sensors (looked kind of purple). Vacuum is still giving me the error. I did notice that some of them have a red led that is visible and some don't (can see with normal light). Does the blinking red led mean anything?
I just got a brand new Shark AI robot (one of the new LiDAR ones). After only using once it’s giving me error #7 saying the cliff sensor is blocked. They are sending me a new unit under warranty. Is it worth me trying to fix this one? I hate to throw out a brand new unit…they don’t want it back. I did recently replace the brush motor in my Shark IQ robot so I have some familiarity with taking it apart.
@@SmittysWorld That is a good idea actually isn’t it? And I can store it in its box since I keep the box anyway so it’s not even taking up any space. Will do. Thanks! Could have used a brush motor recently. 😊
This is EXACTLY my situation and I was hoping replacing one sensor would give me two vacuums for the price of one, but I guess it isn’t worth the time. I’ll save it for parts as suggested, but I am completely bummed by that.
Okay, I found something that absolutely one-hundred-percent fixed my Error 7 issues. After checking all of the sensors and making sure that there was nothing obvious wrong with my Shark IQ, I simply deleted the current map. It was behaving as if it was sitting on a cliff or a drop when it was several feet from one and I wondered if it had become confused and the map was corrupted. After deleting the map I told it to start all over from scratch and it has been working like a charm. Just like brand new. It worked for me so if you don't have any bad sensors or anything else physically wrong with your vacuum, give it a try. You might be as fortunate as I was.
That is awesome information! Thank you for sharing.
And when does the error happen before mapping?
How do I delete the map in it
@@davidwilcox8101under the Map section in the app.
Mine keeps saying too close to a cliff please reposition I am I even resetted it and I cleaned it all and it keeps saying it 😭 I don't even know what to do??
It may be the suspension of the wheels, clean debre or remove the wheels from the robot, or make sure if it lopsidedl
Yea same shit
Nice technique. I have infrared night vision goggles so that makes it a bit easier to see which sensors are working and which don't.
My Shark RV761 will stop working and say that the dust bin is not in the Shark. It is! Enjoyed your video! Thanks
You can probably use any personal security cameras you have in your home that uses night vision mode. I was even able to see the IR with my doorbell camera.
I tested my cliff sensors with a multimeter before I bought replacements and I’m glad I did because the multimeter confirmed the leds for both the transmit and receive were both good regardless of the light test with the camera. The board does have a small black spot on the connector so I’m guessing the board has a burned pin I’ll have to find a way to test the board before buying anything.
how do you test cliff sensors with the multimeter?
Great videos! But I haven't been able to find the model I have - a UR1105ARUS. On mine, the vacuum motor went out - so I purchased a replacement and went to work R&Ring it.... When I removed the top cover, a small PC board (marked 'Dust Cup Hall (or Holl) PCBA) came loss and fell out of its place. Markings in it include the following: E486784, K01-RV-02-05, 0080749. I didn't see where it came from or where it goes back. I completed the repair or the vacuum, except placing that PC board in its rightful place, and it all functions - except that it now has a hard time docking and although the tower does it job, I get an error on my phone "I am unable to empty debris into the dock dust bin. Please empty my dock dust bin and remove blockages.". Do you have any idea where that PC board fits back in place? Thanks in advance!!
Can u please help me. Mine would charge and everything is good but when I hit to work , it stops and it wants me to clean it but it’s already clean ? Can you tell if it’s a sensor? Please advise. Thank you .
Ok. Would be nice to see where we are looking at in the day light
Smitty awesome videos. You got anything that shows how to replace the cliff sensors?
Smitty can you help me find new sensors for my shark av1110arus
shark rv1001ae need to know what next replaced motherboard, two left side sensors and dust bin sensor says ready to clean and does nothing what is next to try
Hey great videos. I have a front left cloff sensor that either looks cracked or something inside. Do you have a video on how to replace it. I called shark and they said they do not sell that part. Thanks
Hi Smitty, is there a way to disable this sensors? I have this error again and again and I don't have stairs or something like that, the robot is just on circles, also getting erro with the boudary strip.
Not to my knowledge
Do you fix Shark IQs?
My shark is having this isue after my dog peed on it. I cleaned it as much as I could. Any suggestions?
I have the same issue
Me too
Yep same, The liquid fucked it up
me too
Where can I find replacement sensors for Model AV2510A0US
Good morning, when my robot shark starts up it says it has problems with the sensors and it doesn't seem to walk in the app it tells me to place it on a flat surface, how can I get it repaired?
Do you have a repair service?
Is there a fix to move the robot to a level surface, error #10? I have moved this thing to a level surface and it is not working any ideas would be great help for me thank you
Can I get wiring for wheels rv1001ea. I broke one taking will out to clean
Is there a way to bypass the cliff sensor? If so, can you show us how? After an hour on customer service with shark, I’ve learned my shark is a brick because of error 7 and there are no replacement sensors. The machine can function just fine if I can get the cliff sensor figured out.
did you ever figure this out? going through the same thing now
Same
Check out my note above. Defending the map fixed my error 7 issues and it works like brand new again.
@@gahvno does not work for me
I bought it and brought it to another country, when I got here as soon as I called it, it presented error number 7 even before mapping, can you help me?
First try deleting the app and resetting the robot
@@SmittysWorldDid not work. But one thing that caught my attention is that even in the dark the lights of no led appear on.
my shark IQ got into dog poo, cleaned everything down to the frame, unit was completely a part. now I get the error #7. I think the sensors are specific and I could have put them in the wrong location. How can I tell which sensor goes where?
How did you clean the robot?
I successfully replaced the cliff sensors in my shark vacuum but now it can't find the dock. It tries to go in front firstr instead of backwards. What did i do that could cause this?
,my guess is that you put the right on the lift and vice versa
What if there isn’t red/white wires? I only* see Red/Black/Orange/Yellow… which of these do I cut?
shouldn't cut them just replace the whole sensor.
So when taking out one of the wheels from my unit, one of the wired connectors got damaged. I cannot for the life of me find a replacement anywhere. Any ideas on where I might get one? I'd hate to have to purchase a new $300 vacuum to replace what is probably a $5 part.
th-cam.com/video/es10eOaGJz4/w-d-xo.html&ab_channel=Smitty%27sWorld in video he states sells parts
You have a dragonfly on your wall
This makes perfect sense. I've used my phone's camera to test infrared emitters for all sorts of things. I'm using a pixel 7 Pro and the camera on that thing is phenomenal so I was able to check for the sensor lights in a fully lit kitchen LOL. Here's my situation that I'm not clear on. Each one of these sensors appears to have two lens pieces both at oblique angles to each other, but there is only one emitter light visible in each one. Does that mean that all the sensors are bad or all of them are good even though I only see one light in each lens set? I did not see any blue lights at all.
Thanks!
There are two sensors, one is the infrared that emits the light and the other is like a camera that measures the distance of the light. I have error code 7 problem sometimes, I cleaned, check did everything and the infrared light are working but I don't know how to diagnose the camera. How do I know wish work and wish is my problem.
Can you show us how to remove the cliff sensors. I bought replacements but it's not obvious how to snap them out
Where did you find replacements? Do you have a link?
Trying to fix my friend's shark IQ.... evidently his ex let her ankle biter dog use the house like it's personal toilet... The shark did it's job over the mess. You get the picture. Have painstaking disassembled and cleaned the whole assembly but am getting an error code 7. Any ideas on how to move forward?
Animal pee is terrible for the electronics sensors are toast probably best to throw it away to be honest if less then a year old clean it up call customer service tell them it doesn’t work see if they will warranty it.
Feel free to use some of my video for clearer shot
I have a Shark AI 2520 and it got the cliff sensor error and resting it didn't work. I of course did the sensible thing and bought new ones. I've replaced all the sensors, but I didn't reattached the wheel cables to the motherboard and now I have no idea which ports they go into. There's only one open port and it's too small for the wheel cable. HAAAAAAALPP
I’d have to see pics of the board to tell you
Yo! How can I send you photos of the board?
black is right and white is left (the plastic connector things)
How do you take of the sunglassy thing to show the sensors?
Pop it off
How do I find someone who works on these robots. I have a brand new one never used and it wont move the clean button and dock button blinks red and green back and forth. None of the vacumn places in my location works on them. And info would be greatly appreciated
It’s not common by any means I’m one of the few that do. If it’s under a year old send it back and get a replacement
@@SmittysWorldany chance you can guide me through error 7. I tried cleaning the sensor with q tips…
@@DLeopoldi914 take your phone and look at the bottom sensors with the lights off should show which one if not all are off
@@SmittysWorld ok all 4 sensors work under my camera light in the dark. I have a shark robot. I cleaned already with qtips and windex now what?
@@DLeopoldi914 more then likely it’s a motherboard issue. Does it look like any moisture in them
Hey smitty,
One of our sensors appears to be busted, do you fix these/sell refurbished robots that will work with our current dock? Thanks
What model do you have?
The problem of abnormal ground inspection
Thank you so much. I’m going. thru this😀😀😀😀😀😀😀
My dog pooped and the shark ran it over. I tried to clean it the best i could but now it says error number 7. Could it be that the battery got wet while i was cleaning it? Should i change the battery? Please help
I’m guessing you Havnt seen my cleaning poop video. What cleaning supplies did you use?
9/10 times with this issue you just need to throw it away to be honest. Error 7 is super hard to get rid of.
So odd question, normally you need a camera to see those red lights ?
Yes for the most part. There are a few lights on them that don’t need a camera but for those you need a camera in a dark room
I washed my shark under water and I didn’t take it apart and it keeps saying error 7 what do I do
Dry it extremely well and hope for best unfortunate 99 percent not gonna work
Uh I don't think it's water proof 🥲
If all 4 cliff sensors work and you still get error 7 is it then a motherboard issue?
Could be or a wiring issue depends what the cause of it starting was
@@SmittysWorld I noticed a little bit of condensation in the sensors but they still work at night.
I have 2 shark robots that are disabled. Can you contact me with parts info that I can purchase from you?
Smittysworld2015@gmail.com
Do you have a list of what each sensor does?
No I don’t
@@SmittysWorld any idea on what could cause this: vacuum can't find dock and seem to get stuck running into wall over and over again. Replaced motherboard but still does the same thing.
@@heatherduperly9869 hmm interesting does your front bumper love freely , did you replace the bump sensors and everything with the motherboard. How did the wheel circuits look
@@SmittysWorld bumper moves freely, wheels move like they should. Motherboard came with a bunch of sensors as part of the board.
Do you know what the dark colored lights do? They almost look purple. They are part of the motherboard and also the side sensors. What about the silver looking sensors? One has a black and yellow wire that leads to the motherboard.
we just bought it and opened the robot today and it mapped the house fine. i wanted to map it again just to make sure it got it correct and now it keeps saying error 7 and to clean the sensors
mine is doing same thing but only on my area rug. it's got big rectangles on it outlined in black with different colors inside, keeps reading the black lines are a cliff and does the whole I side of square no problem til it does it 5 times and then it's done and says the error
Smitty, I'd love to talk to you about my IQ, everything works but it won't charge the battery. I put a new battery in still won't charge. It's like it doesn't know it's on the base. I know the base is good other one works fine.
do you have it backwards? I had an older one that went on charger with the buttons toward the base. the new one I just got has the charger things on the other side. when I first set mine up to let it charge before I used it. came back later and realized I put it backwards so had to wait til next day
I tried the phone trick and saw sensor lighters in all of the front sensors (looked kind of purple). Vacuum is still giving me the error. I did notice that some of them have a red led that is visible and some don't (can see with normal light). Does the blinking red led mean anything?
Not honestly sure could be but no info to know weather it is or not
I just got a brand new Shark AI robot (one of the new LiDAR ones). After only using once it’s giving me error #7 saying the cliff sensor is blocked.
They are sending me a new unit under warranty. Is it worth me trying to fix this one? I hate to throw out a brand new unit…they don’t want it back.
I did recently replace the brush motor in my Shark IQ robot so I have some familiarity with taking it apart.
The problem is either the cliff sensors or motherboard not worth fixing sadly
@@SmittysWorld ☹️ Thanks for the reply. Wish I could fix it and just give it to somebody.
@@amoore2165 Save it for parts
@@SmittysWorld That is a good idea actually isn’t it? And I can store it in its box since I keep the box anyway so it’s not even taking up any space. Will do. Thanks! Could have used a brush motor recently. 😊
This is EXACTLY my situation and I was hoping replacing one sensor would give me two vacuums for the price of one, but I guess it isn’t worth the time. I’ll save it for parts as suggested, but I am completely bummed by that.
couch potato
What?
Dude talks so much instead of getting to the point
Talk to much just get to it
🤣